Lexmark 4600 Series Menus And Messages Manual

www.lexmark.com

Menus and Messages Guide

X

646e

f

February 2006

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,

registered in the United States and/or other countries.

740 West New Circle Road

Lexington, Kentucky 40550

2

Edition: February 2006

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK

INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not

apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these

changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road,

Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services

Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in

any way it believes appropriate without incurring any obligation to you. To obtain additional copies of publications related to this product, visit

the Lexmark Web site at www.lexmark.com.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all

countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product,

program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual

property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except

those expressly designated by the manufacturer, are the user’s responsibility.

Lexmark and Lexmark with diamond design, MarkNet, MarkTrack, and MarkVision are trademarks of Lexmark International, Inc., registered

in the United States and/or other countries.

PCL

®

is a registered trademark of the Hewlett-Packard Company.

The following terms are trademarks or registered trademarks of these companies:

Albertus The Monotype Corporation plc ITC Lubalin Graph International Typeface Corporation

Antique Olive Monsieur Marcel OLIVE ITC Mona Lisa International Typeface Corporation

Apple-Chancery Apple Computer, Inc. ITC Zapf Chancery International Typeface Corporation

Arial The Monotype Corporation plc Joanna The Monotype Corporation plc

CG Times

Based on Times New Roman under license from The

Monotype Corporation plc, is a product of Agfa

Corporation Marigold Arthur Baker

Chicago Apple Computer, Inc. Monaco Apple Computer, Inc.

Clarendon Linotype-Hell AG and/or its subsidiaries New York Apple Computer, Inc.

Eurostile Nebiolo Oxford Arthur Baker

Geneva Apple Computer, Inc. Palatino Linotype-Hell AG and/or its subsidiaries

GillSans The Monotype Corporation plc Stempel Garamond Linotype-Hell AG and/or its subsidiaries

Helvetica Linotype-Hell AG and/or its subsidiaries Taffy Agfa Corporation

Hoefler Jonathan Hoefler Type Foundry Times New Roman The Monotype Corporation plc

ITC Avant Garde

Gothic International Typeface Corporation Univers Linotype-Hell AG and/or its subsidiaries

ITC Bookman International Typeface Corporation

All other trademarks are the property of their respective owners.

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software and

documentation developed exclusively at private expense.

3

Contents

Chapter 1: Using the MFP menus ...................................................................................... 5

Understanding the multifunction printer (MFP) control panel ........................................................................... 5

Home screen ............................................................................................................................................ 8

Using the LCD touch-screen buttons ............................................................................................................. 11

Sample screen one ................................................................................................................................. 11

Information on LCD touch-screen buttons .............................................................................................. 13

Sample screen two ................................................................................................................................. 15

Information on LCD touch-screen buttons .............................................................................................. 15

Other LCD touch-screen buttons ............................................................................................................ 17

Features ................................................................................................................................................. 18

Menus ............................................................................................................................................................19

Menu map ............................................................................................................................................... 19

Paper Menu ................................................................................................................................................... 20

Default Source ........................................................................................................................................ 20

Paper Size/Type ..................................................................................................................................... 20

Configure MP ..........................................................................................................................................23

Envelope Enhance ................................................................................................................................. 23

Substitute Size ........................................................................................................................................ 24

Paper Weight ..........................................................................................................................................25

Paper Loading ........................................................................................................................................ 26

Custom Types ........................................................................................................................................ 26

Custom Names ....................................................................................................................................... 26

Custom Bin Names ................................................................................................................................. 27

Universal Setup ......................................................................................................................................27

Bin Setup ................................................................................................................................................28

Reports .......................................................................................................................................................... 29

Network/Ports ................................................................................................................................................ 31

TCP/IP .................................................................................................................................................... 31

IPv6 ........................................................................................................................................................ 33

E-mail Server Setup ............................................................................................................................... 34

Wireless .................................................................................................................................................. 35

Standard Network or Network <x> .........................................................................................................36

Standard USB or USB <x> ..................................................................................................................... 37

Standard Parallel or Parallel <x> ............................................................................................................ 39

Serial <x> ............................................................................................................................................... 41

NetWare .................................................................................................................................................43

AppleTalk ................................................................................................................................................ 44

LexLink ................................................................................................................................................... 44

Settings .......................................................................................................................................................... 45

General Settings ..................................................................................................................................... 45

Copy Settings .........................................................................................................................................52

Fax Settings ............................................................................................................................................ 57

E-mail Settings ...................................................................................................................................... 66

FTP Settings ........................................................................................................................................... 70

Scan to USB Settings ............................................................................................................................. 74

Print Settings ..........................................................................................................................................76

Security ................................................................................................................................................... 90

4

Contents

Set Date and Time .................................................................................................................................. 96

Help Pages .................................................................................................................................................... 97

Manage Shortcuts ..........................................................................................................................................98

Chapter 2: Understanding MFP messages ................................................................... 100

Status messages ......................................................................................................................................... 100

Fax status messages ................................................................................................................................... 103

Cancel jobs messages ................................................................................................................................. 103

Password and PIN messages ...................................................................................................................... 104

Copy, e-mail, fax, FTP, and scan button messages ....................................................................................104

Attendance messages .................................................................................................................................104

Functions disabled transitional messages ................................................................................................... 124

Index .................................................................................................................................. 125

Using the MFP menus

5

1

Using the MFP menus

Understanding the multifunction printer (MFP) control panel

Most print settings can be changed from the application in use or the print driver. Settings changed from the application or

print driver apply only to the job being sent to the MFP.

Changes made to print settings from an application override changes made from the control panel.

If a setting cannot be changed from the application, use the control panel, MarkVision™ Professional, or the Embedded

Web Server (EWS) pages. Changing a setting from any of these makes that setting the user default.

Whenever a touch screen MFP is attached to a printer, the printer operator panel and any printer operator panel buttons are

disabled. The only panel and buttons that are functional are those on the MFP control panel.

The MFP control panel consists of:

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

9

10

1

2

3

4

5

6

7

8

Understanding the multifunction printer (MFP) control panel

6

Using the MFP menus

Callout Control panel item Function

1 LCD The liquid crystal display (LCD) shows home screen

buttons, menus, menu items, and values. It allows for

making selections within Copy, Fax, and so on.

2 Indicator light Gives information about the status of the MFP using the

colors red and green:

3 0–9

Note: Referred to as the numeric

keypad.

Enter numbers when the LCD screen has a field that

accepts the entry of numbers. Also, use these buttons to

dial phone numbers for faxes.

Note: If a number is pressed while on the home screen

without pressing the # button first, the Copy menu opens

and changes the Copy Quantity.

4 # (Pound or number character) Press this button:

• For a shortcut identifier.

• Within phone numbers. For a Fax number with a #,

enter it twice — ##.

• From the home screen, the Fax Destination List menu

item, E-mail Destination List menu item, or Profile List

menu item to access shortcuts.

5 Dial Pause Cause a two- or three-second dial pause in a fax number.

The button only functions within the Fax menu or with fax

functions.

Redial a fax number from the home screen.

When outside of the Fax menu, fax function, or home

screen, an error beep sounds if Dial Pause is pressed.

When sending a fax, in the Fax To: field, a Dial Pause

press is represented by a comma (,).

6 Clear All When in the function menus, such as Copy, Fax, E-mail,

and FTP, it returns all settings to their default values, and

then returns the MFP to the home screen.

When in any other menu while the MFP is Ready, it

cancels all changes that have not been submitted and

returns the MFP to the home screen.

7 Start Initiate the current job indicated on the control panel.

From the home screen, press it to start a copy job with

the default settings.

The button has no effect if it is pressed while a job runs

through the scanner.

Status Indicates

Off MFP power is off.

Blinking green MFP is warming up, processing data,

or printing a job.

Solid green MFP is on, but idle.

Solid red Operator intervention is required.

Understanding the multifunction printer (MFP) control panel

7

Using the MFP menus

8 Stop Cause the printing or scanning to stop.

During a scan job, the scanner finishes scanning the

current page and then stops, which means paper may

remain in the automatic document feeder (ADF).

During a print job, the print media path is cleared before

the printing stops.

Stopping appears on the control panel during this

process.

9 Backspace Within the Copy menu, which is accessed by touching the

Copy button, press Backspace to delete the right-most

digit of the value in the Copy Count. The default value of

1 appears if the entire number is deleted by pressing

Backspace numerous times.

Within the Fax Destination List, press Backspace to

delete the right-most digit of a number entered manually.

It also deletes an entire shortcut entry. Once an entire

line is deleted, another press of Backspace causes the

cursor to move up one line.

Within the E-mail Destination List, press Backspace to

delete the character to the left of the cursor. If the entry is

in a shortcut, the entire entry is deleted.

10 Asterisk (*) * is used as part of a fax number or as an alphanumeric

character.

Callout Control panel item Function

Understanding the multifunction printer (MFP) control panel

8

Using the MFP menus

Home screen

After the MFP is turned on and a short warm-up period occurs, the LCD shows the following basic screen, which is referred

to as the home screen. Use the LCD touch-screen home screen buttons to open a menu. Once in a menu, use other

buttons to scroll through a list of menu items or values, select a value to change the user default setting, and respond to

messages.

Callout number Button or screen item Function

1 Copy Access the Copy menus.

If the home screen is shown, press a number to access

the Copy menus, too.

2 E-mail Access the E-mail menus. It is possible to scan a

document directly to an e-mail address.

3 Menus (A key is shown on the button.) Access the menus. These menus are only available when

the MFP is in the Ready state.

The Menus button is on a gray bar called the navigation

bar. The bar contains other buttons described as follows.

4 Status message bar Shows the current MFP status, such as Ready or Busy.

Shows MFP conditions, such as Toner Low.

Shows intervention messages to give instructions on

what the user should do so the MFP can continue

processing, such as Close door or insert print

cartridge.

5 Status/Supplies Appears on the LCD whenever the MFP status includes a

message requiring intervention. Touch it to access the

messages screen for more information on the message,

including how to clear it.

1

2

3

4

5

6

7

8

Copy

Fax

E-mail

FTP

Status/

Supplies

Ready. Toner low.

Touch any button to begin.

Menus

Understanding the multifunction printer (MFP) control panel

9

Using the MFP menus

Other LCD touch-screen buttons may appear on the home screen. They are:

6 ? (Tips) All menus have a Tips button. Tips is the

context-sensitive Help feature within the LCD touch

screens.

7 FTP Access the File Transfer Protocol (FTP) menus. A

document can be scanned directly to an FTP site.

8 Fax Access the Fax menus.

Button Button name Function

Release Held Faxes

(or Held Faxes if in

Manual Mode)

There are held faxes with a scheduled hold time previously set. To

access the list of held faxes, touch this button.

Search Held Jobs Search on any of the following items and return any matches:

• User names for held or confidential print jobs

• Job names for held jobs, excluding confidential print jobs

• Profile names

• Bookmark container or job names

• USB container or job names for supported extensions only

Held Jobs Open a screen containing all the held jobs containers.

Lock Device This button appears on the screen when the MFP is unlocked and the

Device Lockout Personal Identification Number (PIN) is not null or

empty.

To lock the MFP:

1 Touch Lock Device to open a PIN entry screen.

2 Enter the correct PIN to lock the control panel which locks both the

control panel buttons and the touch-screen buttons.

Once the control panel is locked, the PIN entry screen clears, and

the Lock Device button is replaced with the Unlock Device button.

Note: If an invalid PIN is entered, Invalid PIN. appears. A pop-up

screen appears with the Continue button shown. Touch Continue. The

home screen returns with the Lock Device button shown.

Callout number Button or screen item Function

Understanding the multifunction printer (MFP) control panel

10

Using the MFP menus

Unlock Device This button appears on the screen when the MFP is locked. The

control panel buttons and shortcuts cannot be used while it appears

and no default copy starts may occur.

To unlock the MFP:

1 Touch Unlock Device to open a PIN entry screen.

2 Enter the correct PIN to unlock the numeric keypad (0–9) and the

Backspace button on the control panel.

Note: If an invalid PIN is entered, Invalid PIN. appears. A pop-up

screen appears with the Continue button shown. Touch Continue. The

home screen returns with the Unlock Device button shown.

Cancel Jobs Open the Cancel Jobs screen. The Cancel Jobs screen shows any of

the following items under three headings on the screen, which are

Print, Fax, and Network:

•print job

•copy job

•fax

•profile

• FTP

• e-mail send

Each heading has its own list of jobs shown in a column under it. Each

column can only show three jobs per screen. Each job appears as a

button. If more than three jobs exist in a column, then the down arrow

appears at the bottom of the column. Each touch of the down arrow

accesses one job in the list. When more than three jobs exist, once the

fourth job in the list is reached, then an up arrow appears at the top of

the column. For illustrations of the up and down arrow buttons, see

Information on LCD touch-screen buttons on page 15.

To cancel a job, see the User’s Guide for instructions.

Button Button name Function

Cancel

Jobs

Using the LCD touch-screen buttons

11

Using the MFP menus

Using the LCD touch-screen buttons

The following section provides information on navigating through several screens. Only a few are chosen to demonstrate

the use of the touch-screen buttons.

Sample screen one

The touch screen appears as follows when the touch screen MFP is a mono printer.

Copy from

Letter (8.5 x 11 in.)

Copy to

Letter (8.5 x 11 in.)

Plain Paper

Sides (Duplex)

Portrait

1-sided to 1-sided

Content

Scale

Auto

(100%)

Darkness

Scan the

ADF

Scan the

flatbed

Back

Text Text/Photo

Photograph Printed Image

Using the LCD touch-screen buttons

12

Using the MFP menus

The touch screen appears as follows when the touch screen MFP is a color printer.

Copy from

Letter (8.5 x 11 in.)

Copy to

Letter (8.5 x 11 in.)

Plain Paper

Sides (Duplex)

1 sided to 1 sided 1 sided to 2 sided

2 sided to 1 sided 2 sided to 2 sided

Scale

Auto

(100%)

Darkness

On

Off

Copy It

Copies:

1

Back

Options

Collate

Using the LCD touch-screen buttons

13

Using the MFP menus

Information on LCD touch-screen buttons

Button Button name Function or description

Select Touch the select button to have another screen appear with additional

items. On the first screen, the user default setting is shown. Once the

select button is touched, and the next screen appears, touching

another item shown on the screen changes the user default setting.

Left scroll decrease Touch the left scroll decrease button to scroll to another value in

decreasing order.

Right scroll increase Touch the right scroll increase button to scroll to another value in

increasing order.

Left arrow Touch the left arrow button to scroll left to:

• Reach a decreased value shown by an illustration.

• See a full text field on the left.

Right arrow Touch the right arrow button to scroll right to:

• Reach an increased value shown by an illustration.

• See a full text field on the right.

Scan the ADF

Scan the flatbed

On the gray navigation bar, these two choices indicate that two types

of scanning are possible. One may choose to scan from the ADF or

the flatbed.

Submit A green button indicates a choice. If a different value within a menu

item is touched, it needs to be saved to become the current user

default setting. To save the value as the new user default setting, touch

Submit.

For information on user default settings, see page 19.

Scan the

ADF

Scan the

flatbed

Submit

Using the LCD touch-screen buttons

14

Using the MFP menus

Back When the Back button is shaped like this, no other navigation is

possible from this screen except to go back. If any other choice is

made on the navigation bar, the screen closes.

For example, in Sample screen one all the selections for scanning

have been made. One of the preceding green buttons should be

touched. The only other button available is Back. Touch Back to return

to the previous screen, and all the settings for the scan job made on

Sample screen one are lost.

Back When the Back button is shaped like this, both forward and backward

navigation is possible from this screen, so there are other options

available on the screen besides selecting Back.

Button Button name Function or description

Back

Using the LCD touch-screen buttons

15

Using the MFP menus

Sample screen two

Information on LCD touch-screen buttons

Button Button name Function or description

Down arrow Touch the down arrow to move down to the next item in a list,

such as a list of menu items or values. The down arrow does

not appear on a screen with a short listing. It only appears if

the entire listing cannot be seen on one screen. On the last

screen of the listing, the down arrow is gray to indicate that it

is not active since the end of the list appears on this screen.

Up arrow Touch the up arrow to move up to the next item in a list, such

as a list of menu items or values. When on the first screen

presented with a long list, the up arrow is gray to indicate that

it is not active. On the second screen, which is needed to

show the rest of the listed items, the up arrow is blue to show

that it is active.

Unselected radio button This is an unselected radio button.

Unknown paper size. Copy from:

Letter (8.5 x 11 in.)

Legal (8.5 x 14 in.)

Executive (7.25 x 10.5 in.)

Continue

Cancel

Job

A4 (210 x 297 mm)

Folio (8. 5 x 13 in.)

Statement (5.5 x 8.5 in.)

Using the LCD touch-screen buttons

16

Using the MFP menus

Selected radio button This is a selected radio button. Touch a radio button to select

it. The radio button changes color to show that it is selected.

In Sample screen two, the only paper size selected is Letter.

Cancel Job See Cancel Jobs on page 10.

Continue Touch Continue after a menu item or value on a screen is

selected and more changes need to be made for a job from

the original screen. Once Continue is touched, the original

screen appears.

For example, if one touched Copy on the home screen, the

Copy screen appears like Sample screen one on page 11.

The following example shows how the Continue button reacts.

1 Touch the select button by the Copy to box, and a new

screen appears.

2 Tou c h MP Feeder, and a new screen appears.

3 Tou c h Legal, and a new screen appears.

4 Tou c h Next, and a new screen appears.

5 Tou c h Plain Paper for the type of print media needed.

6 Tou c h Continue. The Copy screen returns to allow other

selections besides Copy to. The other settings on the Copy

screen available are Duplex, Scale, Darkness, Collate, and

Copies.

To u c h Continue to return to the original screen and make

other setting changes for a copy job before the Copy it

button is touched to start the job.

Button Button name Function or description

Cancel

Job

Continue

Using the LCD touch-screen buttons

17

Using the MFP menus

Other LCD touch-screen buttons

Button Button name Function or description

Custom Allows for creating a custom button based on the

user’s needs.

Cancel Cancel an action or a selection, or cancel out of a

screen and return to the previous screen.

Select Select a menu. The next screen appears showing

menu items.

Select a menu item. The next screen appears showing

values.

Done Specify that a job is finished. For example, when

scanning an original document, one can indicate that

the last page is scanned, and then the print job begins.

Back Return to the previous screen without saving any

settings from the screen.

Note: The Back button appears on each menu screen

except for the home screen.

Home Return to the home screen.

Note: The Home button appears on every screen

except the home screen.

For more information, see the Home screen on

page 8.

Reset active bin Define the active bin as the start bin (the first bin to

receive printed output) in a set of linked bins.

Note: This button only appears when the MFP is in a

stopped state.

Cancel

Done

Back

Reset

active bin

Using the LCD touch-screen buttons

18

Using the MFP menus

Features

Grayed out button When this button appears, it looks faded with a faded

word on it. It means the button is not active or is

unavailable on this screen. It was probably active on

the previous screen, but the selections made on the

previous screen caused it to be unavailable on the

current screen.

For an example, see page 98.

Gray button Touch this button to select the action appearing on the

button.

For an example, see page 99.

Feature Feature name Description

Menus

Æ Settings

Æ Copy Settings

Æ Number of

Copies

Menu trail line A line is located at the top of each menu screen. This

feature acts as a trail. It gives the exact location within the

menus. Touch any of the underlined words to return to

that menu or menu item. The Number of Copies is not

underlined since this is the current screen.

If this feature is used on the Number of Copies screen

before the Number of Copies is set and saved, then the

selection is not saved, and it does not become the user

default setting.

Attendance message alert If an attendance message occurs which closes a

function, such as copy or fax, then a blinking red

exclamation point appears over the function button on the

home screen. This feature indicates an attendance

message exists.

Button Button name Function or description

Menus

19

Using the MFP menus

Menus

Factory defaults are the function settings in effect the first time the MFP is turned on. These remain in effect until they are

changed. To restore factory defaults, select the Restore value from the Factory Defaults menu item.

When a value or setting is selected and saved, it is stored in MFP memory. Once stored, these settings remain active until

new ones are stored or the factory defaults are restored. These settings are called user default settings since the user

selects and saves them.

Note: Settings chosen for faxing, scanning, e-mailing, and copying, and settings for printing from the

application may override the user default settings.

Menu map

The following menu map provides an overview of the menus and menu items available from the control panel. Select a

menu or menu item for more details. For values or settings for each menu item, see the individual descriptions of menu

items following the menu map. There can be an extra level in the menu hierarchy so that it is structured: menu, menu item,

menu item (there can be several more menu items under a menu item), and values.

Click any of the following menus or menu items listed for more information:

Paper Menu

Default Source

Paper Size/Type

Configure MP

Envelope Enhance

Substitute Size

Paper Texture

Paper Weight

Paper Loading

Custom Types

Custom Names

Custom Bin Names

Universal Setup

Bin Setup

Reports

Settings

General Settings

Copy Settings

Fax Settings

E-mail Settings

FTP Settings

Print Settings

Security

Set Date and Time

Reports

Menu Settings Page

Device Statistics

Network Setup Page

Wireless Setup Page

Shortcut List

Fax Job Log

Fax Call Log

E-mail Shortcuts

Fax Shortcuts

FTP Shortcuts

Profiles List

NetWare Setup Page

Print Fonts

Print Directory

Note: The factory default is indicated by an asterisk (*) by the value in the following tables.

Help Pages

Print All

Information Guide

Copying

E-mail

Faxing

FTP

Print Defects

Manage Shortcuts

Manage Fax Shortcuts

Manage E-mail Shortcuts

Manage FTP Shortcuts

Manage Profile Shortcuts

Network/Ports

TCP/IP

IPv6

E-mail Server Setup

Wireless

Standard Network

Network <x>

Standard USB

USB <x>

Standard Parallel

Parallel <x>

Serial <x>

NetWare

AppleTalk

LexLink

Paper Menu

20

Using the MFP menus

Paper Menu

Use the Paper Menu to define settings relating to print media.

Default Source

Use this menu item to define the default print media source.

Paper Size/Type

Note: Only installed print media sources appear for this menu item.

These menu items are used to set the size and type of print media loaded into a source, such as a tray, the multipurpose

feeder, or the manual feed slot. Setting the size and type is a two-step process. In the first menu item, Size appears in bold

letters. After selecting the print media size, the screen changes, and Ty p e appears in bold letters. Select the print media

type.

Menu item Purpose Values and descriptions

Default Source Identifies the default print media

source.

Tray <x> If the same size and type of print media

are in two sources (and the Paper Size

and Paper Type menu items are

correctly set), the sources are

automatically linked. When one source

is empty, print media automatically

feeds from the next linked source.

Tray 1 is the factory default setting.

x represents the tray number, such as

Tray 1 for the standard tray and Tray 2

for an optional tray.

Note: The MP Feeder value, which

stands for the multipurpose feeder, is

shown only when Configure MP is set to

Cassette. See Configure MP for more

information.

MP Feeder

Envelope Feeder

Manual Paper

Manual Env

Menu item Purpose Values and descriptions

Tray <x>

Size

Identifies the default size for each

source.

Only installed sources appear.

Note: For trays with automatic size

sensing, only the value detected by

the hardware appears.

A4* (non-US)

A5

JIS B5

Letter* (US)

Legal

Executive

Folio

Statement

Universal

If the same size and type of print

media is in two sources (and the

Paper Size and Paper Type menu

items are correctly set), the sources

are automatically linked. When one

source is empty, print media

automatically feeds from the next

linked source.

See Tray <x> Type for more

information.

Page is loading ...

Lexmark 4600 Series Menus And Messages Manual

This manual is also suitable for

Lexmark 4600 Series Menus And Messages Manual

Related papers

Other documents