Gigabyte GA-945GM-DS2 User manual

Category
Motherboards
Type
User manual

This manual is also suitable for

GA-945GM(F)-DS2 (rev. 2.0)
Intel
®
Core
TM
2 Extreme dual-core / Core
TM
2 Duo
Intel
®
Pentium
®
D / Pentium
®
4 / Celeron
®
D LGA775 Processor Motherboard
User's Manual
Rev. 2002
12ME-945GMFDR-2002R
* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste
and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!
* The WEEE marking applies only in European Union's member states.
Motherboard
GA-945GM-DS2/
GA-945GMF-DS2 (rev. 2.0)
Nov. 10, 2006
Nov. 10, 2006
Motherboard
GA-945GM-DS2/GA-945GMF-DS2 (rev. 2.0)
Copyright
© 2006 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in the manual are legally registered to their respective companies.
Notice
The written content provided with this product is the property of Gigabyte.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any
means without Gigabyte's prior written permission. Specifications and features are subject to
change without prior notice.
Product Manual Classification
In order to assist in the use of this product, Gigabyte has categorized the user manual in the
following:
î‚„ For detailed product information and specifications, please carefully read the
"Product User Manual".
î‚„ For detailed information related to Gigabyte's unique features, please go to "Technology
Guide" section on Gigabyte's website to read or download the information you need.
For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw
- 4 -
Table of Contents
Item Checklist ................................................................................................................. 6
Optional Accessories ...................................................................................................... 6
GA-945GM(F)-DS2 (rev. 2.0) Motherboard Layout ...................................................... 7
Block Diagram ................................................................................................................ 8
Chapter 1 Hardware Installation ..................................................................................... 9
1-1 Considerations Prior to Installation .................................................................... 9
1-2 Feature Summary .......................................................................................... 10
1-3 Installation of the CPU and CPU Cooler ....................................................... 12
1-3-1 Installation of the CPU ......................................................................................... 12
1-3-2 Installation of the CPU Cooler ............................................................................ 13
1-4 Installation of Memory .................................................................................... 14
1-5 Installation of Expansion Cards ...................................................................... 16
1-6 I/O Back Panel Introduction ........................................................................... 17
1-7 Connectors Introduction .................................................................................. 18
Chapter 2 BIOS Setup ................................................................................................ 29
The Main Menu (For example: GA-945GMF-DS2 BIOS Ver. : F1a) ........................ 30
2-1 Standard CMOS Features ............................................................................. 32
2-2 Advanced BIOS Features .............................................................................. 34
2-3 Integrated Peripherals ..................................................................................... 36
2-4 Power Management Setup ............................................................................. 40
2-5 PnP/PCI Configurations ................................................................................. 42
2-6 PC Health Status ........................................................................................... 43
2-7 Frequency/Voltage Control ............................................................................. 45
2-8 Load Fail-Safe Defaults ................................................................................... 46
2-9 Load Optimized Defaults ................................................................................. 46
2-10 Set Supervisor/User Password ..................................................................... 47
2-11 Save & Exit Setup ......................................................................................... 48
2-12 Exit Without Saving ....................................................................................... 48
- 5 -
Chapter 3 Install Drivers ............................................................................................. 49
3-1 Install Chipset Drivers .................................................................................... 49
3-2 Software Applications ..................................................................................... 50
3-3 Driver CD Information .................................................................................... 50
3-4 Hardware Information ..................................................................................... 51
3-5 Contact Us ..................................................................................................... 51
Chapter 4 Appendix ................................................................................................... 53
4-1 Unique Software Utilities ................................................................................ 53
4-1-1 EasyTune 5 Introduction ..................................................................................... 53
4-1-2 Xpress Recovery2 Introduction ......................................................................... 54
4-1-3 Flash BIOS Method Introduction ........................................................................ 56
4-1-4 2- / 4- / 6- / 8- Channel Audio Function Introduction ...................................... 65
4-2 Troubleshooting ............................................................................................... 70
- 6 -
Item Checklist
IDE Cable x 1, FDD Cable x 1
SATA 3Gb/s Cable x 1
I/O Shield
* The items listed above are for reference only, and are subject to change without notice.
Optional Accessories
î‚Š 2 Ports USB2.0 Cable (Part Number: 12CR1-1UB030-51/R)
î‚Š 4 Ports USB2.0 Cable (Part Number: 12CR1-1UB030-21/R)
î‚Š COM Port Cable (Part Number: 12CF1-1CM001-31/12CF1-1CM001-12R)
î‚Š 2 Ports IEEE 1394 Cable (Part Number: 12CF1-1IE008-01R)
î‚Š SPDIF In and Out Cable (Part Number: 12CR1-1SPINO-11/R)
î‚Š e-SATA Cable (Part Number: 12CF1-3SATPW-11R)
Only for GA-945GMF-DS2.
- 7 -
KB_MS
CD_IN
F_AUDIO
PCIE_16
CODEC
SPDIF_IO
PCI1
PCI2
BATTERY
RTL8111B
ATX_12V
USB
LAN
AUDIO
LPT
USB
COMA
PCIE_1
VGA
LGA775
SYS_FAN
CLR_CMOS
1394
CPU_FAN
ATX
FDD
IDE
DDRII1
DDRII2
DDRII3
DDRII4
IT8718
Intel
®
945G
F1_1394 F2_1394
BIOS
COMB
F_USB1
SATAII0
F_PANEL
Intel
®
ICH7
PWR_LED
F_USB2
SATAII1
SATAII2
SATAII3
CI
TSB43AB23
REV: 2.0
GA-945GM(F)-DS2 (rev. 2.0) Motherboard Layout
GA-945GM-DS2/GA-945GMF-DS2
Only for GA-945GMF-DS2.
- 8 -
Block Diagram
(Note) To use a DDRII 667 memory module on the motherboard, you must install a 1066/800 MHz
FSB processor.
LGA775
Processor
Host
Interface
Intel
®
945G
DDRII 667/533/400 MHz
DIMM
(Note)
Intel
®
ICH7
BIOS
2 PCI
PCI Bus
PCI Express x1
PCI Express Bus
Dual Channel Memory
PCIe CLK
(100 MHz)
4 SATA 3Gb/s
x1
PCI CLK
(33 MHz)
PCIe CLK
(100 MHz)
PCI Express x16
8 USB Ports
IT8718
Floppy
PS/2 KB/Mouse
LPT Port
Center/Subwoofer Speaker Out
Line-Out
MIC
Line-In
SPDIF In
SPDIF Out
Side Speaker Out
Surround Speaker Out
CODEC
COM Ports
RTL
8111B
x1
LAN
RJ45
VGA
CPU CLK+/-(266/200/133 MHz)
ATA 33/66/100 IDE Channel
3 IEEE 1394a
TSB43AB23
Only for GA-945GMF-DS2.
Hardware Installation- 9 -
English
1-1 Considerations Prior to Installation
Preparing Your Computer
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the
instructions below:
1. Please turn off the computer and unplug its power cord.
2. When handling the motherboard, avoid touching any metal leads or connectors.
3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components
(CPU, RAM).
4. Prior to installing the electronic components, please have these items on top of an antistatic pad or
within a electrostatic shielding container.
5. Please verify that the power supply is switched off before unplugging the power supply connector
from the motherboard.
Installation Notices
1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required
for warranty validation.
2. Prior to the installation of the motherboard or any hardware, please first carefully read the information
in the provided manual.
3. Before using the product, please verify that all cables and power connectors are connected.
4. To prevent damage to the motherboard, please do not allow screws to come in contact with the
motherboard circuit or its components.
5. Please make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
6. Please do not place the computer system on an uneven surface.
7. Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
8. If you are uncertain about any installation steps or have a problem related to the use of the product,
please consult a certified computer technician.
Instances of Non-Warranty
1. Damage due to natural disaster, accident or human cause.
2. Damage as a result of violating the conditions recommended in the user manual.
3. Damage due to improper installation.
4. Damage due to use of uncertified components.
5. Damage due to use exceeding the permitted parameters.
6. Product determined to be an unofficial Gigabyte product.
Chapter 1 Hardware Installation
GA-945GM(F)-DS2 (rev. 2.0) Motherboard - 10 -
English
1-2 Feature Summary
CPU î‚Š LGA775 for Intel
®
Core
TM
2 Extreme dual-core / Core
TM
2 Duo / Pentium
®
D /
Pentium
®
4 / Celeron
®
D
î‚Š L2 cache varies with CPU
Front Side Bus î‚Š Supports 1066/800/533 MHz FSB
Chipset î‚Š Northbridge: Intel
®
945G Express Chipset
î‚Š Southbridge: Intel
®
ICH7
LAN î‚Š Onboard Realtek RTL8111B chip (10/100/1000 Mbit)
Audio î‚Š Onboard Realtek ALC888 CODEC chip
î‚Š Supports High Definition Audio
î‚Š Supports 2 / 4 / 6 / 8 channel audio
î‚Š Supports S/PDIF In/Out connection
î‚Š Supports CD In connection
IEEE 1394 î‚Š Onboard T.I. TSB43AB23 chip
î‚Š 3 IEEE 1394a ports
Storage î‚Š Intel
®
ICH7 Southbrigde
- 1 FDD connector, allowing connection of 1 FDD device
- 1 IDE connector with UDMA 33/ATA 66/ATA 100 support, allowing
connection of 2 IDE devices
- 4 SATA 3Gb/s connectors, allowing connection of 4 SATA 3Gb/s
devices
O.S Support î‚Š Microsoft Windows
®
2000/XP
Memory î‚Š 4 DDRII DIMM memory slots (supports up to 4 GB memory)
(Note 1)
î‚Š Supports dual channel DDRII 667/533/400 unbuffered DIMMs
(Note 2)
î‚Š Supports 1.8V DDRII DIMMs
Expanstion Slots î‚Š 1 PCI Express x16 slot
î‚Š 1 PCI Express x1 slot
î‚Š 2 PCI slots
Internal Connectors î‚Š 1 24-pin ATX power connector
î‚Š 1 4-pin ATX 12V power connector
î‚Š 1 floppy connector
î‚Š 1 IDE connector
î‚Š 4 SATA 3Gb/s connectors
î‚Š 1 CPU fan connector
î‚Š 1 system fan connector
î‚Š 1 front panel connector
î‚Š 1 front audio connector
î‚Š 1 CD In connector
î‚Š 1 S/PDIF In/Out connector
î‚Š 2 USB 2.0/1.1 connectors for additional 4 ports by cables
î‚Š 2 IEEE 1394a connectors for additional 2 ports by cables
î‚Š 1 COMB connector
î‚Š 1 Chassis Intrusion connector
î‚Š 1 power LED connector
Only for GA-945GMF-DS2.
Hardware Installation- 11 -
English
(Note 1) Due to standard PC architecture, a certain amount of memory is reserved for system usage
and therefore the actual memory size is less than the stated amount. For example, 4 GB of
memory size will instead be shown as 3.xx GB memory during system startup.
(Note 2) To use a DDRII 667 memory module on the motherboard, you must install a 1066/800 MHz
FSB processor.
(Note 3) EasyTune functions may vary depending on different motherboards.
Rear Panel I/O î‚Š 1 PS/2 keyboard port
î‚Š 1 PS/2 mouse port
î‚Š 1 parallel port
î‚Š 1 serial port (COMA)
î‚Š 1 VGA port
î‚Š 4 USB 2.0/1.1 ports
î‚Š 1 IEEE 1394a port
î‚Š 1 RJ-45 port
î‚Š 6 audio jacks (Line In / Line Out / MIC In/Surround Speaker Out (Rear
Speaker Out)/Center/Subwoofer Speaker Out/Side Speaker Out)
I/O Control î‚Š IT8718 chip
Hardware Monitor î‚Š System voltage detection
î‚Š CPU temperature detection
î‚Š CPU / System fan speed detection
î‚Š CPU warning temperature
î‚Š CPU / System fan failure warning
î‚Š CPU smart fan control
BIOS î‚Š 1 4 Mbit flash ROM
î‚Š Use of licensed AWARD BIOS
Additional Features î‚Š Supports @BIOS
î‚Š Supports Download Center
î‚Š Supports Q-Flash
î‚Š Supports EasyTune (only supports Hardware Monitor function)
(Note 3)
î‚Š Supports Xpress Install
î‚Š Supports Xpress Recovery2
î‚Š Supports Xpress BIOS Rescue
Bundle Software î‚Š Norton Internet Security (OEM revision)
Form Factor î‚Š Micro ATX form factor; 24.4cm x 23.3cm
Only for GA-945GMF-DS2.
GA-945GM(F)-DS2 (rev. 2.0) Motherboard - 12 -
English
1-3 Installation of the CPU and CPU Cooler
Before installing the CPU, please comply with the following conditions:
1. Please make sure that the motherboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong
direction, the CPU will not insert properly. If this occurs, please change the insert direction
of the CPU.
3. Please add an even layer of heat sink paste between the CPU and CPU cooler.
4. Please make sure the CPU cooler is installed on the CPU prior to system use,
otherwise overheating and permanent damage of the CPU may occur.
5. Please set the CPU host frequency in accordance with the processor specifications. It
is not recommended that the system bus frequency be set beyond hardware specifica-
tions since it does not meet the required standards for the peripherals. If you wish to set
the frequency beyond the proper specifications, please do so according to your hard-
ware specifications including the CPU, graphics card, memory, hard drive, etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your computer system requires all
of the following platform components:
- CPU: An Intel
®
Pentium 4 Processor with HT Technology
- Chipset: An Intel
®
Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optimizations for HT Technology
1-3-1 Installation of the CPU
Fig. 1
Gently lift the metal
lever located on the
CPU socket to the
upright position.
Metal Lever
Fig. 2
Remove the plastic
covering on the CPU
socket.
Fig. 3
Notice the small gold
colored triangle located
on the edge of the CPU
socket. Align the
indented corner of the
Fig. 4
Once the CPU is
properly inserted,
please replace the
load plate and push the
metal lever back into
its original position.
CPU with the triangle and gently insert the CPU into
position. (Grasping the CPU firmly between your
thumb and forefinger, carefully place it into the socket
in a straight and downwards motion. Avoid twisting or
bending motions that might cause damage to the CPU
during installation.)
Hardware Installation- 13 -
English
1-3-2 Installation of the CPU Cooler
The CPU cooler may adhere to the CPU as a result of hardening of the heat paste. To prevent
such an occurrence, it is suggested that either thermal tape rather than heat paste be used for
heat dissipation or using extreme care when removing the CPU cooler.
Fig. 6
Finally, please attach the power connector of the
CPU cooler to the CPU fan header located on the
motherboard.
Fig. 3
Place the CPU cooler atop the CPU and make
sure the push pins aim to the pin hole on the
motherboard.Pressing down the push pins
diagonally.
Fig. 4
Please make sure the Male and Female push pin
are joined closely. (for detailed installation
instructions, please refer to the CPU cooler instal-
lation section of the user manual)
Fig. 5
Please check the back of motherboard after
installing. If the push pin is inserted as the picture,
the installation is complete.
Fig.1
Please apply an even layer of CPU cooler paste
on the surface of the installed CPU.
Fig. 2
(Turning the push pin along the direction of arrow is to
remove the CPU cooler, on the contrary, is to install.)
Please note the direction of arrow sign on the male
push pin doesn't face inwards before installation. (This
instruction is only for Intel boxed fan)
Male Push Pin
Female Push Pin
The top of Female Push Pin
GA-945GM(F)-DS2 (rev. 2.0) Motherboard - 14 -
English
The motherboard supports DDRII memory modules, whereby BIOS will automatically detect memory
capacity and specifications. Memory modules are designed so that they can be inserted only in one direction.
The memory capacity used can differ with each slot.
Before installing the memory modules, please comply with the following conditions:
1. Please make sure that the memory used is supported by the motherboard. It is
recommended that memory of similar capacity, specifications and brand be used.
2. Before installing or removing memory modules, please make sure that the computer
power is switched off to prevent hardware damage.
3. Memory modules have a foolproof insertion design. A memory module can be installed
in only one direction. If you are unable to insert the module, please switch the direction.
1-4 Installation of Memory
Notch
DDRII
Fig.1
The DIMM socket has a notch, so the DIMM memory mod-
ule can only fit in one direction. Insert the DIMM memory
module vertically into the DIMM socket. Then push it down.
Fig.2
Close the plastic clip at both edges of the DIMM sockets to
lock the DIMM module.
Reverse the installation steps when you wish to remove
the DIMM module.
Hardware Installation- 15 -
English
Dual Channel Memory Configuration
The GA-945GM-DS2/GA-945GMF-DS2 (rev. 2.0) supports the Dual Channel
Technology. After operating the Dual Channel Technology, the bandwidth of
memory bus will double.
The GA-945GM-DS2/GA-945GMF-DS2 (rev. 2.0) includes 4 DIMM sockets, and each Channel has
two DIMM sockets as following:
Channel 0 : DDRII1, DDRII2
Channel 1 : DDRII3, DDRII4
If you want to operate the Dual Channel Technology, please note the following explanations due to the
limitation of Intel chipset specifications.
1. Dual Channel mode will not be enabled if only one DDRII memory module is installed.
2. To enable Dual Channel mode with two or four memory modules (it is recommended to use
memory modules of identical brand, size, chips, and speed), you must install them into DIMM
sockets of the same color.
The following is a Dual Channel Memory configuration table:
(DS: Double Side, SS: Single Side, "--": Empty)
DDR II1 DDR II2 DDR II3 DDR II4
DS/SS - - DS/SS - -
- - DS/SS - - DS/SS
DS/SS DS/SS DS/SS DS/SS
2 memory modules
4 memory modules
GA-945GM(F)-DS2 (rev. 2.0) Motherboard - 16 -
English
1-5 Installation of Expansion Cards
You can install your expansion card by following the steps outlined below:
1. Read the related expansion card's instruction document before install the expansion card into the
computer.
2. Remove your computer's chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
For example: Installing a PCI Express x16 VGA card:
To release an installed card, users can
also press the latch on the opposite side
of the drawable bar as the picture to the
left shows.
Please carefully pull out the small white-
drawable bar at the end of the PCI Ex-
press x16 slot when you try to install/
uninstall the VGA card. Please align the
VGA card to the onboard PCI Express
x16 slot and press firmly down on the
slot. Make sure your VGA card is locked
by the small white-drawable bar.
Hardware Installation- 17 -
English
1-6 I/O Back Panel Introduction
PS/2 Keyboard and PS/2 Mouse Connector
To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the
keyboard to the lower port (purple).
Parallel Port
The parallel port allows connection of a printer, scanner and other peripheral devices.
COMA (Serial Port)
Connects to serial-based mouse or data processing devices.
VGA Port
Monitor can be connected to VGA port.
USB Port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such
as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make
sure your OS supports USB controller. If your OS does not support USB controller, please contact
OS vendor for possible patch or driver upgrade. For more information please contact your OS or
device(s) vendors.
IEEE 1394 Port
Serial interface standard set by the Institute of Electrical and Electronics Engineers, which has
features like high speed, high bandwidth and hot plug.
LAN Port
The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of 10/100/
1000Mbps.
Center/Subwoofer Speaker Out
The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected to
Center/Subwoofer Speaker Out jack.
Surround Speaker Out (Rear Speaker Out)
The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be
connected to Surround Speaker Out (Rear Speaker Out) jack.
Side Speaker Out
The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Out
jack.
Only for GA-945GMF-DS2 (rev. 2.0).
GA-945GM(F)-DS2 (rev. 2.0) Motherboard - 18 -
English
1-7 Connectors Introduction
Line In
The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.
Line Out (Front Speaker Out)
The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround
speakers can be connected to Line Out (Front Speaker Out) jack.
MIC In
The default MIC In jack. Microphone must be connected to MIC In jack.
In addition to the default speakers settings, the ~ audio jacks can be reconfigured to
perform different functions via the audio software. Only microphones still MUST be connected
to the default Mic In jack ( ) . Please refer to the 2-/4-/6-/8- channel audio setup steps for
detailed software configuration information.
1) ATX_12V
2) ATX (Power Connector)
3) CPU_FAN
4) SYS_FAN
5) FDD
6) IDE
7) SATAII0 / 1 / 2 / 3
8) PWR_LED
9) BATTERY
10) F_PANEL
11) F_AUDIO
12) CD_IN
13) SPDIF_IO
14) F_USB1 / F_USB2
15) F1_1394 / F2_1394
16) COMB
17) CLR_CMOS
18) CI
2
1
14
7
18
5
12
15
8
3
10
4
11
6
9
17
13 16
Only for GA-945GMF-DS2.
Hardware Installation- 19 -
English
1/2) ATX_12V / ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the
components on the motherboard. Before connecting the power connector, please make sure that
all components and devices are properly installed. Align the power connector with its proper
location on the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
connector is not connected, the system will not start.
Caution!
Please use a power supply that is able to handle the system voltage requirements. It is
recommended that a power supply that can withstand high power consumption be used (300W or
greater). If a power supply is used that does not provide the required power, the result can lead to
an unstable system or a system that is unable to start.
If you use a 24-pin ATX power supply, please remove the small cover on the power connector
on the motherboard before plugging in the power cord ; otherwise, please do not remove it.
131
24
12
Pin No. Definition
13 3.3V
14 -12V
15 GND
16 PS_ON(soft On/Off)
17 GND
18 GND
19 GND
20 -5V
21 +5V
22 +5V
23 +5V (Only for 24-pin ATX)
24 GND(Only for 24-pin ATX)
Pin No. Definition
1 3.3V
2 3.3V
3 GND
4 +5V
5 GND
6 +5V
7 GND
8 Power Good
9 5V SB(stand by +5V)
10 +12V
11 +12V(Only for 24-pin ATX)
12 3.3V(Only for 24-pin ATX)
Pin No. Definition
1 GND
2 GND
3 +12V
4 +12V
13
2
4
ATX_12V
ATX
GA-945GM(F)-DS2 (rev. 2.0) Motherboard - 20 -
English
3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)
The cooler fan power connector supplies a +12V power voltage via a 3-pin (SYS_FAN) /4-pin
(CPU_FAN) power connector and possesses a foolproof connection design.
Most coolers are designed with color-coded power connector wires. A red power connector wire
indicates a positive connection and requires a +12V power voltage. The black connector wire is
the ground wire (GND).
Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to pre-
vent CPU damage or system hanging caused by overheating.
1
Pin No. Definition
1 GND
2 +12V / Speed Control
3 Sense
4 Speed Control
SYS_FAN
CPU_FAN :
Pin No. Definition
1 GND
2 +12V
3 Sense
SYS_FAN :
5) FDD (Floppy Connector)
The FDD connector is used to connect the FDD cable while the other end of the cable connects to
the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and
2.88MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD
connector.
CPU_FAN
1
234
133
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Gigabyte GA-945GM-DS2 User manual

Category
Motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI