Kichler Lighting 44287WWW User manual

Brand
Kichler Lighting
Model
44287WWW
Type
User manual

Kichler Lighting 44287WWW is a lighting fixture designed for indoor use. It comes with all the necessary mounting hardware, including screws, straps, and a canopy. The fixture can be adjusted to suit the position of the fixture. It also includes a grounding wire for safety. The fixture can be connected to either parallel cord or insulated wire, depending on the type of wiring in your home. The fixture can accommodate one bulb, which is not included. The fixture is easy to install, with clear and concise instructions included.

Kichler Lighting 44287WWW is a lighting fixture designed for indoor use. It comes with all the necessary mounting hardware, including screws, straps, and a canopy. The fixture can be adjusted to suit the position of the fixture. It also includes a grounding wire for safety. The fixture can be connected to either parallel cord or insulated wire, depending on the type of wiring in your home. The fixture can accommodate one bulb, which is not included. The fixture is easy to install, with clear and concise instructions included.

IS-44287-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
3) Make wire connecons. Reference chart below for
correct connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
4) Push xture to wall. Be sure not to pinch wires between
wall and canopy of xture.
5) Screw in two (2) mounng screws[D], one on each side
of the canopy[E]. Tighten to secure.
6) Thread the lower trim piece[F] onto the boom of the
lamp socket.
7) Install the recommended bulb (Not supplied).
8) Lower the glass[G] over the installed bulb.
Fixture Diagram
Parts List
[A] Mounting
Strap
[B] Outlet Box
[C] Strap
Mounting
Screws
[D] Mounting
Screws
[E] Canopy
[F] Lower Trim
[G] Glass
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
Installaon Instrucons (connued)
G
A
C
D
F
E
B
1) Aach mounng strap[A] to outlet box[B] using the
strap mounng screws[C]. Mounng strap can be
adjusted to suit posion of xture.
2) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire connector
(Not provided) aer following the above steps. Never
connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
IS-44287-US
Estamos aquí para ayudarle 866-558-5706
Horario: Lunes-Viernes 9am a 5pm EST (hora ocial del este)
3) Haga les conexiones de los alambres. La tabla de
referencia de abajo indica las conexiones correctas y los
alambres correspondientes.
Conectar el alambre de
suministro negro o rojo al
Conectar el alambre de
suministro blanco al
Negro Blanco
*Cordon paralelo (redondo
y liso)
*Cordon paralelo (cuadrado
y estriado)
Claro, marrón, amarillio
o negro sin hebra
idencadora
Claro, marrón, amarillio
o negro con hebra
idencadora
Alambre aislado (diferente
del verde) con conductor
de cobre
Alambre aislado (diferente
del verde) con conductor
de plata
*Nota: Cuando se uliza alambre
paralelo (SPT 1 y SPT 2). El alambre
neutro es de forma cuadrada o
estriada y el otro alambre será
de forma redonda o lisa. (Vea la
ilustracíón).
Hilo Neutral
4) Empuje el artefacto a la pared. Asegúrese de no pellizcar
los alambres entre la pared y el escudete del artefacto.
5) Atornille dos (2) tornillos de montaje[D], uno a cada lado
de la cubierta[E].
6) Instale la moldura inferior[F] y enrosque en la parte
inferior del portalámparas.
7) Inserte la bombilla recomendada (No suministrada).
8) Baje el cristal[G] sobre la bombilla instalada.
Diagrama de Accesorios
Lista de Partes
[A] Abrazadera
de Montaje
[B] Caja de Salida
[C] Tornillos de
Montaje de la
Correa
[D] Tornillos de
Montaje
[E] Cubierta
[F] Moldura
Inferior
[G] Cristal
Precauciones
PRECAUCIÓN – RIESGO DE DESCARGA ELÉCTRICA –
Desconecte la electricidad en el panel principal del
interruptor automáco o caja principal de fusibles antes de
comenzar y durante la instalación.
ADVERTENCIA:
Este accesorio está desnado a la instalación de
acuerdo con el Naonal Electrical Code (NEC) y todas las
especicaciones del código local. Si no está familiarizado
con los requisitos del código, la instalación se recomienda
un electricista cercado.
Instrucciones de Instalación
Instrucciones de Instalación (connuación)
G
A
C
D
F
E
B
1) Acople la abrazadera de montaje[A] a la caja de
salida[B] con los tornillos de montaje de la correa[C]. La
abrazadera de montaje se puede ajustar para acomodar
la posición del artefacto
2) Instrucciones de conexión a erra solamente para los
Estados Unidos. (Vea la ilustracion a o b).
a) En las lámparas que enen el eje, de montaje con
un agujero y dos hoyuelos realzados, enrollar el
alambre a erra de la caja tomacorriente alrededor
del tornillo verde y pasarlo por el aquiero.
b) En las lámparas con una arandela acopada, jar el
alambre a erra de la caja tomacorriente del ajo de
la arandela acoada y tornillo verde, y paser por el
eje de montaje.
Si la lámpara viene con alambre a erra, conecter el
alambre a erra de la lámpara al alambre a erra de la caja
tomacorriente con un conector de alambres (No incluido)
espués de seguir los pasos anteriores. Nunca conectar el
alambra a erra a los alambres eléctros negro o blanco.
ARANDELA
CONCAVA
TIERRA DE LA
CAJA DE SALIDA
TORNILLO DE TIERRA,
VERDE
DEPRESIONES
TIERRA
ARTEFACTO
CONECTOR DE ALAMBRE
TIERRA DE LA
CAJA DE SALIDA
TORNILLO DE TIERRA,
VERDE
TIERRA
ARTEFACTO
a
b
  • Page 1 1
  • Page 2 2

Kichler Lighting 44287WWW User manual

Brand
Kichler Lighting
Model
44287WWW
Type
User manual

Kichler Lighting 44287WWW is a lighting fixture designed for indoor use. It comes with all the necessary mounting hardware, including screws, straps, and a canopy. The fixture can be adjusted to suit the position of the fixture. It also includes a grounding wire for safety. The fixture can be connected to either parallel cord or insulated wire, depending on the type of wiring in your home. The fixture can accommodate one bulb, which is not included. The fixture is easy to install, with clear and concise instructions included.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents