Page is loading ...
BARCOMED
®
2MP2 and
2MP1NT
Imaging Boards
Hardware Installation Guidelines
For Boards Rev. A - Rev.G
KM570630/00
September 26, 2000
Page 2
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
NOTICE
Although every attempt has been made to achieve technical accuracy in this
document, we assume no responsibility for errors that may be found. Our goal is
to provide you with the most accurate and usable documentation possible; if you
discover errors, please let us know.
BARCO Metheus software products are the property of BARCO Metheus. They
are distributed under copyright by BARCO Metheus, for use only under the
specific terms of a software license agreement between BARCO Metheus and
the licensee. No other use, duplication, or disclosure of a BARCO Metheus
software product, in any form, is authorized.
The specifications of BARCO Metheus products are subject to change without
notice.
TRADEMARKS
All Trademarks and registered trademarks are of their respective companies.
COPYRIGHT
This document is copyrighted. All rights are reserved. This document may not,
in whole or in part, be copied, photocopied, reproduced, translated or reduced to
an electronic medium or machine readable form without prior written consent
from BARCO Metheus, Inc.
FCC CLASS A NOTICE
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules, when installed in a
suitable host. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instruction manual, it
may cause harmful interference in which case the user will be required to correct
the interference at his own expense.
© 2000 BarcoView, Inc. — Metheus Division. All rights reserved.
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
Page
3
CONTENTS
2MP2 PRODUCT OVERVIEW ............................................................5
Features of the BarcoMed 2MP2......................................................5
Minimum System Requirements.......................................................5
Supported Resolutions.....................................................................5
For Each Head of the 2MP2.............................................................5
2MP1NT PRODUCT OVERVIEW ........................................................6
Features of the BarcoMed 2MP1NT..................................................6
Minimum System Requirements.......................................................6
Supported Resolutions.....................................................................6
HARDWARE INSTALLATION............................................................7
Installing the BarcoMed 2MP2 or 2MP1NT Graphics Controller ..........7
Running Multiple BarcoMed 2MP Boards in a Single Host..................9
APPENDIX A...................................................................................11
2MP2 Splitter Cable.......................................................................11
System configuration guidelines .....................................................11
Page 4
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
Page
5
2MP2 PRODUCT OVERVIEW
The BarcoMed 2MP2 Graphics Controller delivers a
quality 1200 x 1600 pixel image with 256
simultaneous shades of gray for medical imaging
applications.
Features of the
BarcoMed 2MP2
§ Dual Head Configuration
§ 1200 x 1600 resolution at 75 Hz
§ 10 bit input DAC
§ 4 MB Video Memory (VRAM)
§ Portrait or Landscape Mode
§ 256 Simultaneous shades of gray from a Palette
of 1024
§ Fully compatible with the BarcoMed 2MP1NT
§ Hardware cursor
§ Single slot PCI card
§ Optional Photometer Kit
§ Display properties control panel to dynamically
change display settings
§ Control Panel supports the English ( U.S. ) ,
Dutch, German, Korean and Japanese
languages
Minimum System
Requirements
§ PCI slot with no obstructions
§ Sufficient power and cooling (see Appendix,
"System Configuration Guidelines")
§ Multi-sync displays or a separate VGA card and
display
Supported Resolutions
For Each Head of the
2MP2
§ 1200x1600 @ 75 Hz (primary)
§ 1200x1600@74Hz
§ 1200x1600 @ 66 Hz
§ 1600x1200 @ 80 Hz
§ 1280x1024 @ 75 Hz
§ 1024x1280 @ 70Hz
§ 1024x768 @ 75 Hz
§ 800x600 @ 75 Hz
§ 640x480 @ 75 Hz
Page 6
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
2MP1NT PRODUCT OVERVIEW
The BarcoMed 2MP1NT Graphics Controller delivers
a quality 1200 x 1600 pixel image with 256
simultaneous shades of gray for medical imaging
applications.
Features of the
BarcoMed 2MP1NT
§ 1200 x 1600 resolution at 75 Hz
§ 10 bit input DAC
§ 4 MB Video Memory (VRAM)
§ Portrait or Landscape Mode
§ 256 Simultaneous shades of gray from a Palette
of 1024
§ Fully compatible with the BarcoMed 2MP2
§ Hardware cursor
§ Single slot PCI card
§ Optional Photometer Kit
§ Display properties control panel to dynamically
change display settings
§ Control Panel supports the English ( U.S. ),
Dutch, German, Korean, and Japanese
languages
Minimum System
Requirements
§ PCI slot with no obstructions
§ Sufficient power and cooling (see Appendix,
"System Configuration Guidelines")
§ Multi-sync displays or a separate VGA card and
display
Supported Resolutions § 1200x1600 @ 75 Hz (primary)
§ 1200x1600@74Hz
§ 1200x1600 @ 66 Hz
§ 1600x1200 @ 80 Hz
§ 1280x1024 @ 75 Hz
§ 1024x1280 @ 70Hz
§ 1024x768 @ 75 Hz
§ 800x600 @ 75 Hz
§ 640x480 @ 75 Hz
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
Page
7
HARDWARE INSTALLATION
Installing the BarcoMed
2MP2 or 2MP1NT
Graphics Controller
Notice: Wear a protective ESD strap during
installation or handling of the board. Electrostatic
charges can damage the board.
Figure 1: The 2MP2 and 2MP1NT
To install the 2MP2 or 2MP1 NT into your computer,
follow these steps:
1) Turn off the power to your computer and
disconnect the power cord.
2) Remove the chassis cover according to the
manufacturer’s instructions. Be sure to observe
safety warnings.
3) Check the setting of the VGA jumper (JP3) on
the graphics board. By default, VGA will be
disabled (the jumper will be on the pins). This
jumper setting will allow you to use a separate
VGA card and display as a boot console. In
order for you to use the on-board VGA on the
board, you need a multi-sync display and you
must enable the VGA by removing the jumper
from the pins.
VGA Jumper
Page 8
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
NOTE: If you have a separate VGA card and it
has a Cirrus chip, you must remove it from your
system before installing the 2MP2 or 2MP1NT.
If you have on-board VGA that uses a Cirrus
chip, consult your system manual on how to
disable it before installing the BarcoMed board.
Once the system VGA is disabled, you must
ensure that the BarcoMed board's VGA jumper
is enabled if you want to see your boot
messages.
4) Install the 2MP2 or 2MP1NT Graphics
Controller into a free PCI slot. Be sure that the
board is seated firmly in the slot.
5) Secure the card to the chassis with the PC's I/O
panel mounting screw, and replace the chassis
cover.
6) Connect the displays to the uppermost
connector on the 2MP2 or 2MP1NT (the output
farthest from the motherboard - see figure 2)
using the provided video cable. Note that the
left-hand display should be connected to A and
the right hand display (if there is one) should be
connected to B.
Figure 2: The video
outputs.
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
Page
9
Running Multiple
BarcoMed 2MP Boards
in a Single Host
NOTE: To run multiple BarcoMed 2MP2s,
multiple 2MP1NTs, or any combination of the
two in a single host with VGA enabled, you need
to enable the VGA jumper on only ONE of the
BarcoMed 2MP2s and disable the VGA jumper
on ALL other BarcoMed boards.
The physical order of the displays may vary
when you are running multiple BarcoMed 2MP
boards. This is due to the PC's PCI bus control
in the system BIOS, and not the BarcoMed
board. It may become necessary, depending on
how your PC's BIOS configures the PCI bus, to
switch your BNC display connections to achieve
a linear desktop configuration.
7) Each half of the display cable has three
connectors on it. The green one is the video,
the black one is the horizontal sync, and the
white one is the vertical sync.
8) Install the power cord, turn on the power, and
boot the system as usual.
Page 10
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
BarcoMed 2MP2 and 2MP1NT Hardware Installation Guide
Page
11
APPENDIX A
2MP2 Splitter Cable
(Separate Option)
DB 15 Connector B
A
B
IDC type 26 position
Connector
DB 15 Connector A
The following tables describe the pin out for the
2MP2 splitter cable.
DB15
Connector A
Signal Name IDC type 26
position
Connector
Pin 2 video Pin 3
Pin 7 video ground Pin 4
Pin 10 sync ground Pin 10
Pin 13 hsync Pin 7
Pin 14 vsync Pin 9
Pin 2 video Pin 16
Pin 7 video ground Pin 17
Pin 10 sync ground Pin 23
Pin 13 hsync Pin 20
Pin 14 vsync Pin 22
If you make your own cables, you must tie all
grounds (earths) together and to the shell of the
connector closest to the graphics card.
System configuration
guidelines
Because of the low power consumption and
low heat generation of the 2MP2 and 2MP1NT,
multiple boards may be installed in adjacent
PCI slots or adjacent to other PCI boards.
Additionally there should be no need to modify
either the PC's power supply and/or cooling
system.
BarcoView Inc.
3059 Premiere Parkway
Duluth, GA 30097-4905, U.S.A.
Phone: +1-678-475-8000 – Fax: +1-678-475-8100
E-mail: [email protected]
BarcoView
Theodoor. Sevenslaan 106
B-8500 Kortrijk, Belgium
Phone: +32 56 233 244 - Fax: +32 233 374
E-mail: [email protected]
www.barcomedical.com
/