Page is loading ...
Page 1
BarcoMed
®
2MP2 and 2MP1NT
Imaging Boards
Rev. L and Higher
Hardware Installation Guidelines
KM570647/02
December 21, 2001
Page 2
NOTICE
Although every attempt has been made to achieve technical accuracy
in this document, we assume no responsibility for errors that may be
found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.
BarcoView, LLC software products are the property of BarcoView,
LLC They are distributed under copyright by BarcoView, LLC, for use
only under the specific terms of a software license agreement
between BarcoView, LLC and the licensee. No other use, duplication,
or disclosure of a BarcoView, LLC software product, in any form, is
authorized.
The specifications of BarcoView, LLC products are subject to change
without notice.
TRADEMARKS
All trademarks and registered trademarks are of their respective
companies.
COPYRIGHT
This document is copyrighted. All rights are reserved. This document
may not, in whole or in part, be copied, photocopied, reproduced,
translated or reduced to an electronic medium or machine readable
form without prior written consent from BarcoView, LLC.
FCC CLASS A NOTICE
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules, when installed in a suitable host. These limits are designed to
provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instruction manual, it may
cause harmful interference in which case the user will be required to
correct the interference at his own expense.
© 2001 BarcoView, LLC — Metheus Division. All rights reserved.
Page 3
CONTENTS
Product Overviews ................................................................................ 5
2MP2 Product Overview ................................................................................5
Introduction.............................................................................................5
Features of the BarcoMed 2MP2 ...........................................................5
Minimum System Requirements ............................................................5
Supported Resolutions For Each Head of the 2MP2 .............................5
2MP1NT Product Overview ...........................................................................7
Introduction.............................................................................................7
Features of the BarcoMed 2MP1NT.......................................................7
Minimum System Requirements ............................................................7
Supported Resolutions ...........................................................................7
HARDWARE INSTALLATION ................................................................ 9
Familiarizing Yourself With the BarcoMed 2MP2 or BarcoMed 2MP1NT
Imaging Board ........................................................................................9
Jumper Location ....................................................................................9
Using the VGA Capabilities of the BarcoMed 2MP2 or BarcoMed
2MP1NT..........................................................................................9
Standard Jumper Functions .................................................................10
Installing the BarcoMed 2MP2 or 2MP1NT Graphics Controller..........11
Running Multiple BarcoMed 2MP Boards in a Single Host ..................12
Page 4
(This page intentionally left blank.)
Page 5
PRODUCT OVERVIEWS
2MP2 Product Overview
Introduction
The BarcoMed 2MP2 Graphics Controller delivers a quality 1200 x
1600 pixel image with 256 simultaneous shades of gray for medical
imaging applications.
Features of the BarcoMed 2MP2
• Dual Head Configuration
• 1200 x 1600 resolution at 75 Hz
• 10 bit input DAC
• 4 MB Video Memory (VRAM)
• Portrait or Landscape Mode
• 256 Simultaneous shades of gray from a Palette of 1024
• Fully compatible with the BarcoMed 2MP1NT
• Hardware cursor
• Single slot PCI card
• Display Properties Control Panel to dynamically change display
settings
• Control Panel support for the English ( U.S. ), Dutch, German,
Japanese, Korean, Simplified Chinese and Traditional Chinese
languages
Minimum System Requirements
• PCI slot with no obstructions
• PCI 2.1 Compliant System
• VGA compatible high resolution displays or a separate VGA card
and display
• NT 4.0 SP4 and above, Windows 2000 SP1 and above, or
Windows XP
Supported Resolutions For Each Head of the 2MP2
• 1600x1200 @ 80 Hz
• 1280x1024 @ 75 Hz
• 1200x1600 @ 66 Hz
Page 6
• 1200x1600 @ 74 Hz
• 1200x1600 @ 75 Hz (primary)
• 1024x768 @ 75 Hz
• 1024x1280 @ 67 Hz
• 1024x1280 @ 70 Hz
• 800x600 @ 75 Hz
• 640x480 @ 75 HZ
Page 7
2MP1NT Product Overview
Introduction
The BarcoMed 2MP1NT Graphics Controller delivers a quality 1200 x
1600 pixel image with 256 simultaneous shades of gray for medical
imaging applications.
Features of the BarcoMed 2MP1NT
• Single Head Configuration
• 1200 x 1600 resolution at 75 Hz
• 10 bit input DAC
• 4 MB Video Memory (VRAM)
• Portrait or Landscape Mode
• 256 Simultaneous shades of gray from a Palette of 1024
• Fully compatible with the BarcoMed 2MP2
• Hardware cursor
• Single slot PCI card
• Display Properties Control Panel to dynamically change display
settings
• Control Panel support for the English ( U.S. ), Dutch, German,
Japanese, Korean, Simplified Chinese and Traditional Chinese
languages
Minimum System Requirements
• PCI slot with no obstructions
• PCI 2.1 Compliant System
• VGA compatible high resolution displays or a separate VGA card
and display
• NT 4.0 SP4 and above, Windows 2000 SP1 and above, or
Windows XP
Supported Resolutions
• 1600x1200 @ 80 Hz
• 1280x1024 @ 75 Hz
• 1200x1600 @ 66 Hz
• 1200x1600 @ 74 Hz
• 1200x1600 @ 75 Hz (primary)
Page 8
• 1024x768 @ 75 Hz
• 1024x1280 @ 67 Hz
• 1024x1280 @ 70 Hz
• 800x600 @ 75 Hz
• 640x480 @ 75 HZ
Page 9
HARDWARE INSTALLATION
Notice: Wear a protective ESD strap during installation or handling of
the board. Electrostatic charges can damage the board.
Familiarizing Yourself With the BarcoMed 2MP2 or BarcoMed
2MP1NT Imaging Board
Prior to installing your 2MP2 or 2MP1NT board(s) in your PC please
take a few minutes to familiarize yourself with both the board and the
PCI slots in your computer.
Figure 1: The BarcoMed 2MP2 and BarcoMed 2MP1NT
Jumper Location
There is one user settable jumper on the BarcoMed 2MP2 and
BarcoMed 2MP1NT. It is used to enable or disable the VGA
capabilites of the board.
Using the VGA Capabilities of the BarcoMed 2MP2 or
BarcoMed 2MP1NT
Prior to installing the BarcoMed 2MP2 or BarcoMed 2MP1NT, decide
if you are going to use its on-board VGA capabilities. If you are,
Page 10
check the setting of the Jumper at J-100 on the graphics board. (See
Figure 1 on the preceding page.) By default, VGA should be
disabled, i.e. on both pins. If you decide to use your multisyncing high
resolution grayscale monitor as your boot monitor, you must enable
the on-board VGA capabilities of the BarcoMed 2MP2 or 2MP1NT
Imaging Board by removing the jumper from the pins at J-100. We
suggest placing the jumper on only one of the two pins, so that you
don’t lose the jumper.
NOTE: To use multiple BarcoMed 2MP2 and/or BarcoMed 2MP1NT
Imaging Board(s) in a single host with VGA enabled, you need to
enable VGA on only ONE of the BarcoMed 2MP2 and/or BarcoMed
2MP1NT Imaging Board(s) and disable VGA on ALL other BarcoMed
Imaging Board(s).
Standard Jumper Functions
repmuJ noitcnuF
001PJ.)sniPffO(elbaneAGVyramirP
.ylnoyalpsidyramirprofnepO
,002PJ
,102PJ
,601PJ
,101PJ
,301PJ
501PJ
.ylnognitsetyrotcaF
.egnahCTONoD
Figure 2: 2MP2 and 2MP1NT Jumper Settings Table
Page 11
Installing the BarcoMed 2MP2 or 2MP1NT Graphics Controller
To install the BarcoMed 2MP2 or BarcoMed 2MP1NT into your
computer, follow these steps:
1) Turn off the power to your computer and disconnect the power
cord.
2) Remove the chassis cover according to the manufacturer’s
instructions. Be sure to observe safety warnings.
3) If you have decided to use the on-board VGA capabilities of the
BarcoMed 2MP2 or BarcoMed 2MP1NT (see Using the VGA
capabilities of the BarcoMed 2MP2 or BarcoMed 2MP1NT), you
must now remove any VGA cards that are currently installed in
the computer. You may also need to uninstall the drivers for that
VGA board. (Consult the User Guide for your VGA board for
instructions on removing the driver.) If your system has an
integrated VGA card you may need to make changes to your
system’s BIOS settings in order to use the VGA capabilities of your
BarcoMed board. (Consult your system manual(s) for instructions
on making changes to the BIOS settings.)
SPECIAL NOTE: If you have a separate VGA card and it has a
Cirrus chip, you must remove it from your system before installing
the BarcoMed 2MP2 or BarcoMed 2MP1NT. If you have on-board
VGA that uses a Cirrus chip, consult your system manual on how
to disable it before installing the BarcoMed board(s). Once the
system VGA is disabled, you must ensure that the BarcoMed
board’s VGA capabilities are enabled if you want to see your boot
messages.
4) Install the BarcoMed 2MP2 or BarcoMed 2MP1NT Graphics
Controller into a free PCI slot. Be sure that the board is seated
firmly in the slot.
5) Secure the card to the chassis with the PC’s I/O panel mounting
screw, and replace the chassis cover.
6) Connect the left-hand display to the uppermost connector on the
BarcoMed 2MP2 or BarcoMed 2MP1NT (VID 1 - see figure 3 on
next page) using the provided video cable. For a dual-headed
BarcoMed 2MP2 setup, connect the right-hand display to the other
connector (VID 2) on the board.
7) Each of the display cables has three BNC connectors on it. The
green one is the video, the black one is the horizontal sync, and
the white one is the vertical sync.
8) Install the power cord, turn on the power, and boot the system as
usual.
Page 12
Running Multiple BarcoMed 2MP Boards in a Single Host
NOTE: The physical order of the displays may vary when you are
running multiple BarcoMed 2MP boards. This is due to the PC’s PCI
bus control in the system BIOS, and not the BarcoMed board. It may
become necessary, depending on how your PC’s BIOS configures the
PCI bus, to switch your BNC display connections to achieve a linear
desktop configuration.
Figure 3: The Video Outputs.
/