CAUTION: Some parts have sharp edges. Care must be taken when handling
the various pieces to avoid a mishap. For safety sake, please read the safety
information provided in this manual before beginning construction. Wear
gloves when handling metal parts.
ASSEMBLY INSTRUCTIONS FOR
STORETTE
STA42 A01
15-2860910 English 09/10
2
AH02
CONTENTS
•Pre-construction instructions • Anchoring the frame
•Assembling the building • Parts List and order information
PROCEED WITH CONFIDENCE
It might look complicated when you first unpack your building…but it really isn’t. Simply follow the
illustrated instructions and your building will go up quickly and accurately.
ASSEMBLY INSTRUCTIONS
•Before beginning construction...check local building codes regarding footings, location
and other requirements. Study and understand the owner's manual.
•You will need assistance…you’ll find that another person will speed the job and make
assembly easier.
•Selecting your site…choose an area that’s firm and level yet allows drainage away from
site.
WARNING! … DO NOT ERECT YOUR BUILDING IN AREAS THAT ARE SUBJECTED TO
HIGH WINDS, OR ERECT ON A WINDY DAY. ANY BUILDING LEFT PARTIALLY CON-
STRUCTED MAY BE SERIOUSLY DAMAGED IF LEFT IN THIS STATE.
•Sort and separate all parts and hardware…checking with the Parts List on Page 4 and
the illustrations on Page 5…be sure you have all parts and know where they belong in the
building. Each part has been numbered or illustrated, the quantity required and its part
number noted.
Foundation Preparation
• Hammer and Nails
• Spade or Shovel
• Hand Saw / Power Saw
• Lumber and/or Concrete
Optional Time-Savers
• Wrench / Nut Driver
• Electric / Cordless Drill
• Square
• String (for squaring frame)
Required
• Utility Knife / Scissors
• Pliers
• Carpenter's Level
• Tape Measure
Required
• Eye Goggles
• No. 2 Phillips Screwdriver
(with Hardened Magnetic Tip)
• Work Gloves
• Step Ladders
BUILDING CARE
•Carefree maintenance – Your building has been designed to give you years of carefree
service. All parts have been precision engineered for a perfect fit. It is manufactured from
heavily galvanized steel with exterior parts pre-enameled on both sides at the steel mill.
•IMPORTANT – This building is designed to withstand normal wind loads when
installed according to instructions. Manufacturer cannot be held responsible for
any consequences due to buildings that are not installed per instructions or for
damage due to weather conditions or acts of God.
•Follow step-by-step instructions carefully…complete
each step before going onto the next one.
•Retain this manual after assembly is completed…it
contains a complete parts list.
A03
IMPORTANT
PERSONAL SAFETY DURING BUILDINGS CONSTRUCTION
Prior to assembly some of the buildings components may contain sharp edges, wear protective
work gloves while handling these components. When using any form of power tool wear eye
protection. Do not use household voltage power tools in a wet or damp environment. Household
voltage power tools must be monitored and controlled by a Ground Fault Interrupter or more
commonly called a G.F.I. Do not use any part of the buildings frame as a means of personal support
while attaching components during assembly.
PREPARATION OF BUILDING SITE
This building must be constructed on a SOLID
BASE FOUNDATION. We recommend a
poured concrete pad or large size concrete
patio stone squares for a suitable floor and
base. Which ever you select…make sure your
foundation area is firm and level and will allow
drainage away from the site. Make your solid
base foundation at least 4” (100mm) larger than
your building. Spacemaker is not respon-
sible for the choice and the construction of
the foundation.
NOTE: For a concrete pad base, prepare a
level bed for a firm footing layer of crushed
stone. The concrete pad should then be poured
to a thickness of 4” (100mm) to 5” (125mm).
When completed allow to dry thoroughly for at
least 48 hours.
YOUR BUILDING MUST BE
ANCHORED
Your building must be firmly anchored to your concrete
pad or large concrete patio stone squares…to help
protect against damage in high winds.
FURTHER ANCHORING INSTRUCTIONS
FOLLOW AFTER ALL WALL AND ROOF
PANELS HAVE BEEN INSTALLED.
MODEL "A" "A" "B" "B"
CM INCH CM INCH
4x2 124.5 49 62.2 24 1/2
3
OUTSIDE MEASUREMENTS OF BUILDING AT BASE
“B” + 100mm (4")
MINIMUM
“A” + 100mm (4")
MINIMUM
"A"
"B"
4
A04
ILLUSTRATED PARTS
NOTE: DRAWINGS ARE NOT TO SCALE, BUT ARE DESIGNED TO SHOW CROSS
SECTIONS AND GENERAL CONFIGURATION TO AID IDENTIFICATION.
REAR BASE RAIL (1)
No. 840H
SIDE BASE RAIL (2)
No. 3J
REAR TOP RAIL (1)
No. 840H
SIDE TOP RAIL (2)
No. 3J
FRONT BASE RAIL (1)
No. 6J
CORNER PANEL (4)
No. 5J
REAR WALL PANEL (1)
No. 21J
DOOR TRACK (1)
No. 6J
DOOR JAMB (2)
No. 109J
ROOF COVER PANEL (1)
No. 419J
DOOR PANEL (2)
No. F23J
DOOR GLIDE (4)
No. A67
DOOR LATCH FINGER (1)
No. 10J
CORNER GUSSET (8)
No. 51J
SCREW CLIPS (16)
No. 85J
ROOF SUPPORT ARM
BRACKET (1)
No. 9J
ROOF COVER HINGE (2)
No. 55J ROOF CORNER CAP (4)
No. 60H
ROOF SUPPORT ARM (1)
No. 13J
ROOF EDGE TRIM (2)
No. 16J
(TOP & BOTTOM)
ROOF EDGE TRIM (2)
No. 17J (SIDES)
ROOF LATCH BRACKET (1)
No. 8J
ROOF SUPPORT ARM
LATCH PLATE (1)
No. 14J
ROOF COVER BRACE (SHORT) (2)
No. 40J
ROOF COVER BRACE (LONG) (1)
No. 1036M
Parts List
Assembly Part Part Quantity
Key No. Number Description in Carton
840H Rear Base Rail 1
6J Front Base Rail 1
3J Side Base Rail 2
5J Corner Panel 4
21J Rear Wall Panel 1
840H Rear Top Rail 1
3J Side Top Rail 2
6J Door Track 1
109J Door Jamb 2
F23J Door Panel 2
419J Roof Cover Panel 1
17J Roof Edge Trim (Sides) 2
16J Roof Edge Trim (Top & Bottom) 2
1036M Roof Cover Brace (Long) 1
40J Roof Cover Brace (Short) 2
13J Roof Support Arm 1
BT1 Weather Stripping (1/2"x3/8"x12') 1 Roll
Owner's Manual 1
51J Corner Gusset 8
DH10 Door Handle 2
P61 Plastic Washers 1
14J Roof Support Arm Latch Plate 1
Hardware Kit (Bolts, Nuts and Screws) 1
A67 Door Glide 4
10J Door Latch Finger 1
85J Screw Clips (12-122) 16
60H Roof Corner Cap 4
8J Roof Latch Bracket 1
55J Roof Cover Hinge 2
9J Roof Support Arm Bracket 1
A05
5
IMPORTANT...When ordering parts please provide number stamped on the surface of galvanized
parts. In the case of wall and roof panels please provide the model number of the building,
color and size of panels. To order parts please use order form on the last page.
Assemble rear base rail and front base
rail to side base rails with corner gussets
at each corner as shown… and place on
flat surface.
STEP
1
6
A06
Install 4 corner panels to base frame as shown…
Do not fasten panels to front base rail. Then install narrow rear wall panel in correct
position.
STEP
2
REAR PANEL
No. 21J
DOORWAY
DOORWAY
USE SELF TAPPING SCREWS..10mm (3/8") LONG
CORNER PANEL
No. 5J
INSTALL PANELS IN
THIS SEQUENCE.
USE SELF TAPPING SCREWS...10mm (3/8") LONG
SIDE BASE RAIL
No. 3J
NOTE - LONG SLOT ON SIDE
FRONT BASE RAIL
No. 6J
USE 10mm (3/8") LONG
BOLTS AND NUTS
REAR BASE RAIL
No. 840H
CORNER
GUSSETS
No. 51J
ALL WALL PANELS ARE TO BE
ATTACHED TO TOP RAIL AND BASE
RAIL WITH SCREWS.
STEP
3
7
A07
CORNER GUSSET
No. 51J
SIDE TOP RAIL
No. 3J
(with Long Slot on Top)
1. Slide 4 door glides into door track (as shown).
STEP
4
SLIDE DOOR GLIDES INTO DOOR TRACK
INSIDE
OUTSIDE
No. A67
DOOR GLIDE
FRONT
IMPORTANT PLACE FRONT EDGE OF
DOOR TRACK WITH THESE HOLES
FACING THE OUTSIDE.
DOOR
TRACK
No. 6J
1. Install door track to front end of side rails
with front corner gussets as shown.
Fasten only in holes indicated.
STEP
5USE SELF TAPPING SCREWS
...10mm (3/8") LONG
CORNER GUSSET
No. 51J
NOTE
Do not fasten
corner panels to
door track at front.
DOOR TRACK
No. 6J
USE SELF TAPPING
SCREWS...10mm
(3/8") LONG
USE SELF TAPPING
SCREW...10mm
(3/8") LONG
1. Install rear top rail and fasten to wall panels.
2. Fasten side top rail to wall panels.
3. Install 2 rear corner gussets
and fasten only in holes indicated.
REAR TOP RAIL
No. 840H
USE 10mm (3/8") LONG
BOLT AND NUT
1. Carefully swing front section of corner panel away from door track. Position door jamb on side
of doorway. Then fasten top and bottom directly to door track and front base rail. See “A”.
2. Then swing corner panel back into position and fasten to door track and front base rail.
See “B” & “C”. Repeat for other side.
STEP
6
8
A08
CORNER PANEL
"A"
DOOR TRACK
DOOR JAMB (RIGHT)
No. 109J DOOR JAMB
(RIGHT) No. 109J
DOOR
TRACK
CORNER PANEL CORNER PANEL
"B" "C"
DOOR
TRACK
DOOR JAMB
(RIGHT) No. 109J
USE PLASTIC
WASHERS
STEP
7
VIEWED FROM
OUTSIDE BUILDING
USE 13mm (1/2")
LONG BOLTS AND NUTS
1. Inside and near the corner of build-
ing, install bottom lip of left door
into track formed in base rail.
2. Position top of door so that holes
in door line up with center holes in
door glide. Fasten inner door glide
(nearest to left door jamb) to door
using 10mm (3/8”) long bolts and
nuts. Position door latch finger
(10J) behind door panel and fas-
ten through outer door glide using
10mm (3/8”) bolts and nuts.
See “A”
3. Install right hand door in the same
manner but without the door latch
finger.
STEP
8
INSIDE
LEFT RIGHT
OUTSIDE
DOOR ADJUSTMENT
There are 3 holes in each of the
door glides to raise or lower
doors as required so that they
meet squarely
INSTALL DOOR INTO TRACK IN
BASE RAIL AND TILT
UP INTO PLACE
USE 10mm (3/8")
LONG BOLTS AND NUTS
INSIDE OF BUILDING
INSIDE VIEW LEFT
DOOR
ONLY
DOOR TRACK
OUTSIDE INSIDE
Door Latch Finger
NOTE - 2 GLIDES PER DOOR
OUTSIDE INSIDE
LEFT RIGHT
VIEWED
FROM
OUTSIDE
Door Handle
"B"
DOOR INSTALLATION
1. Attach door handle using
bolts as shown in “A”.
2. Install two 6mm (1/4”) bolts
and nuts with plastic washers
at bottom of each door panel.
See “B”.
"A"
1. Turn roof cover panel upside down… be sure hole pattern matches sketch…See “A”
below.
2. Install screw clips (85J) over edge of roof cover panel exactly as shown at the hole
positions indicated. See “C”.
1. With panel still upside down, position roof edge trim, 17J (with most holes facing upwards)
over sides of panel so that holes line up with screw clips. Fasten through roof cover panel
with screws and washers. NOTE: Leave the 2 holes, 1 on each side of the center ridge
– on the left hand side of the panel, open. See “A” below.
2. Position roof edge trim, 16J, (with most holes facing upwards) over ends of side trim. Line
up holes and with 22mm (7/8”) long bolts and washers, fasten corner caps to 4 corners
through top of roof cover panel.
Leave other holes open. See “B” and “C”.
STEP
9
STEP
10
9
“B”
No. 16J
ROOF
EDGE
TRIM
“B”
No. 16J
ROOF
EDGE
TRIM
USE SELF TAPPING SCREWS AND
WASHERS…10mm (3/8”) LONG
No. 17J
ROOF EDGE TRIM
(SIDES)
No. 16J
ROOF EDGE TRIM
(TOP & BOTTOM)
USE 22mm (7/8”) LONG
BOLTS AND NUTS
LEAVE
OPEN
"B" LEAVE OPEN
"C"
No. 60H
ROOF CORNER CAP
No. 419J
ROOF COVER PANEL
(UPSIDE DOWN)
A09
No. 60H
ROOF CORNER CAP
"C"
SCREW CLIP "C"
No. 85J
SCREW CLIP
"C"
"A"
LINE UP HOLES
LEAVE OPEN
"C"
SCREW CLIP
LINE UP HOLES
No. 17J
ROOF
EDGE
TRIM
“A” No. 17J
ROOF
EDGE
TRIM
“A”
1. Position roof cover brace (long) 1036M diagonally as shown to the underside of panel.
Fasten through top of panel into brace, at the 2 center holes only, using 10mm (3/8”) long
bolts and nuts with plastic washers.
2. Position roof cover braces (short) 40J, vertically over ends of diagonal brace (1036M) with
ends of each short brace under the lips of the top and bottom roof edge trim. Fasten through
top of roof cover panel with 10mm (3/8”) screws and plastic washers in center area only.
3. Fasten extreme end of braces (40J) where they pass under the roof edge trim (16J) with
22mm (7/8”) long bolts, nuts and plastic washers.
STEP
11
10
USE SELF TAPPING SCREWS
AND PLASTIC WASHERS…10mm
(3/8”) LONG IN CENTER AREA
USE 22mm (7/8”) LONG BOLTS
AND NUTS AT ENDS OF ROOF
COVER BRACES (SHORT) ROOF COVER BRACE
(LONG) No. 1036M
ROOF COVER BRACE
(SHORT) No. 40J
A10
1. Install roof latch bracket (8J) to top of roof cover with 10mm (3/8”) bolt and nut with plastic
washer and 22mm (7/8”) bolt and nut with plastic washer. See “A”. NOTE: Leave nuts
slack for later adjustments.
2. Tap into place screw clips over the 2 double holes in bottom roof trim (16J). Fasten roof
cover hinges (narrow side) to roof cover assembly as shown. See “B”.
3. Complete the securing of braces to roof by using 10mm (3/8”) and 22mm (7/8”) bolts and
nuts with plastic washers where required.
4. With help – fasten completed roof cover assembly to base unit by using 10mm (3/8”)
screws, through hinges into rear corner gussets and rear top rail. See “C”. NOTE:
For a stronger attachment, place screw clips (85J) under holes in rear top rail and
tightenscrews into clips.
STEP
12
X-SECTIONAL ASSEMBLY VIEW PLASTIC
WASHERS
USE 10mm (3/8")
BOLT AND NUT
USE 22mm (7/8")
BOLT AND NUT
USE SELF TAPPING SCREWS
10mm (3/8") LONG
WITH SCREW CLIPS
HINGE
ROOF EDGE TRIM
BOTTOM
USE SELF
TAPPING SCREWS
10mm (3/8") LONG
"C"
ROOF HINGE
No. 55J
"A"
"B"
1. Install roof support arm latch plate (14J) on left, top side rail (3J) with two 10mm (3/8”) screws
so that the slotted holes in each piece overlap as shown. See “A”
2. Assemble roof support arm (13J) and roof support arm bracket (9J) with a 10mm (3/8”) bolt
and locknut. Leave slack. See “B”
3. On the left side of roof, slide roof support arm bracket beneath roof edge trim so that its holes
line up with open holes in roof edge trim. Attach with 10mm (3/8”) long screws and plastic
washers. See “D”
4. Slide other end of support arm (13J) through slot in side top rail, so that notch in arm hooks
into the overlapped slot in top rail to support roof in the open position. Install bolt and nut
in bottom hole of arm.
See “C”
5. Cut self adhesive weatherstripping to length and apply to top rails, as shown in “E”.
6. Grease hinges.
7. With lid shut adjust roof latch bracket (8J) so that door latch finger (10J) on left hand door,
engages with roof latch bracket to lock lid. Tighten the 2 bolts that hold roof latch bracket
to roof.
8. Use large center holes in bottom gussets to anchor unit, if required.
STEP
13
SCREW CLIP
ROOF PANEL
ROOF SUPPORT
ARM BRACKET
"D"
PLASTIC WASHER
USE 10mm (3/8")
LONG SCREWS
SECTION OF 3J
X-SECTIONAL VIEW
11
LEAVE APPROX. 1/2"
WEATHERSTRIPPING
ROOF SUPPORT
ARM No. 13J
"C"
USE 10mm (3/8") BOLT
ROOF SUPPORT
ARM BRACKET
No. 9J
USE
10mm (3/8")
BOLT
LOCKNUT
"B"
WALL PANEL/REINFORCING RIB
TOP RAIL OR
DOOR TRACK
"E"
A11
ROOF
SUPPORT ARM
LATCH PLATE
No. 14J
"A"
REPLACEMENT PARTS OR ANY QUESTIONS REGARDING YOUR BUILDING SHOULD BE
REFERRED DIRECTLY TO THE FACTORY. DO NOT CONTACT YOUR DEALER, THEY
ARE NOT EQUIPPED TO SERVICE YOUR REQUESTS AS PROMPTLY AS THE
CUSTOMER SERVICE DEPARTMENT AT THE FACTORY (1-800-851-1085).
PARTS REPLACEMENT ORDER FORM
** MODEL NO.______________ **
PART NO. QTY. COLOR
FOR PARTS REPLACEMENT PLEASE CONTACT
CUSTOMER SERVICE DEPARTMENT.
TELEPHONE NO. (1-800-851-1085)
NAME:
ADDRESS:
CITY: PROVINCE/STATE:
POSTAL CODE/ZIP: TELEPHONE:
PURCHASED FROM:
STORE ADDRESS:
DATE PURCHASED:
A12
Parts Required
or Mail To: Spacemaker, Ltd.
3069 Wolfedale Road
Mississauga, Ontario L5C 1V9
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Spacemaker HW88 Owner's manual
-
Arrow GA1025 Operating instructions
-
-
-
-
-
Arrow Storage Products VY1014 Installation guide
-
-
-
Other documents
-
Spectrum HHZ3280H Operating instructions
-
Hoshizaki SRC-14J Remote Condenser User manual
-
-
-
Lenovo 6290 Hardware Maintenance Manual
-
Arrow Storage Products 697.6889 User manual
-
Craftsman CVCS107 Installation guide
-
Kawasaki Mule 3000 Installation guide
-
Alton AMATEUR CEDAR GREENHOUSE 6' Wide Assembly Instructions Manual
-
Arrow Plastic CL72-A User manual
