Arrow STA42 Owner's manual

Brand: Arrow

Model: STA42

Type: Owner's manual

CAUTION: Some parts have sharp edges. Care must be taken when handling

the various pieces to avoid a mishap. For safety sake, please read the safety

information provided in this manual before beginning construction. Wear

gloves when handling metal parts.

ASSEMBLY INSTRUCTIONS FOR

STORETTE

STA42 A01

15-2860910 English 09/10

AH02

CONTENTS

•Pre-construction instructions • Anchoring the frame

•Assembling the building • Parts List and order information

PROCEED WITH CONFIDENCE

It might look complicated when you first unpack your building…but it really isn’t. Simply follow the

illustrated instructions and your building will go up quickly and accurately.

ASSEMBLY INSTRUCTIONS

•Before beginning construction...check local building codes regarding footings, location

and other requirements. Study and understand the owner's manual.

•You will need assistance…you’ll find that another person will speed the job and make

assembly easier.

•Selecting your site…choose an area that’s firm and level yet allows drainage away from

site.

WARNING! … DO NOT ERECT YOUR BUILDING IN AREAS THAT ARE SUBJECTED TO

HIGH WINDS, OR ERECT ON A WINDY DAY. ANY BUILDING LEFT PARTIALLY CON-

STRUCTED MAY BE SERIOUSLY DAMAGED IF LEFT IN THIS STATE.

•Sort and separate all parts and hardware…checking with the Parts List on Page 4 and

the illustrations on Page 5…be sure you have all parts and know where they belong in the

building. Each part has been numbered or illustrated, the quantity required and its part

number noted.

Foundation Preparation

• Hammer and Nails

• Spade or Shovel

• Hand Saw / Power Saw

• Lumber and/or Concrete

Optional Time-Savers

• Wrench / Nut Driver

• Electric / Cordless Drill

• Square

• String (for squaring frame)

Required

• Utility Knife / Scissors

• Pliers

• Carpenter's Level

• Tape Measure

Required

• Eye Goggles

• No. 2 Phillips Screwdriver

(with Hardened Magnetic Tip)

• Work Gloves

• Step Ladders

BUILDING CARE

•Carefree maintenance – Your building has been designed to give you years of carefree

service. All parts have been precision engineered for a perfect fit. It is manufactured from

heavily galvanized steel with exterior parts pre-enameled on both sides at the steel mill.

•IMPORTANT – This building is designed to withstand normal wind loads when

installed according to instructions. Manufacturer cannot be held responsible for

any consequences due to buildings that are not installed per instructions or for

damage due to weather conditions or acts of God.

•Follow step-by-step instructions carefully…complete

each step before going onto the next one.

•Retain this manual after assembly is completed…it

contains a complete parts list.

A03

IMPORTANT

PERSONAL SAFETY DURING BUILDINGS CONSTRUCTION

Prior to assembly some of the buildings components may contain sharp edges, wear protective

work gloves while handling these components. When using any form of power tool wear eye

protection. Do not use household voltage power tools in a wet or damp environment. Household

voltage power tools must be monitored and controlled by a Ground Fault Interrupter or more

commonly called a G.F.I. Do not use any part of the buildings frame as a means of personal support

while attaching components during assembly.

PREPARATION OF BUILDING SITE

This building must be constructed on a SOLID

BASE FOUNDATION. We recommend a

poured concrete pad or large size concrete

patio stone squares for a suitable floor and

base. Which ever you select…make sure your

foundation area is firm and level and will allow

drainage away from the site. Make your solid

base foundation at least 4” (100mm) larger than

your building. Spacemaker is not respon-

sible for the choice and the construction of

the foundation.

NOTE: For a concrete pad base, prepare a

level bed for a firm footing layer of crushed

stone. The concrete pad should then be poured

to a thickness of 4” (100mm) to 5” (125mm).

When completed allow to dry thoroughly for at

least 48 hours.

YOUR BUILDING MUST BE

ANCHORED

Your building must be firmly anchored to your concrete

pad or large concrete patio stone squares…to help

protect against damage in high winds.

FURTHER ANCHORING INSTRUCTIONS

FOLLOW AFTER ALL WALL AND ROOF

PANELS HAVE BEEN INSTALLED.

MODEL "A" "A" "B" "B"

CM INCH CM INCH

4x2 124.5 49 62.2 24 1/2

OUTSIDE MEASUREMENTS OF BUILDING AT BASE

“B” + 100mm (4")

MINIMUM

“A” + 100mm (4")

MINIMUM

"A"

"B"

A04

ILLUSTRATED PARTS

NOTE: DRAWINGS ARE NOT TO SCALE, BUT ARE DESIGNED TO SHOW CROSS

SECTIONS AND GENERAL CONFIGURATION TO AID IDENTIFICATION.

REAR BASE RAIL (1)

No. 840H

SIDE BASE RAIL (2)

No. 3J

REAR TOP RAIL (1)

No. 840H

SIDE TOP RAIL (2)

No. 3J

FRONT BASE RAIL (1)

No. 6J

CORNER PANEL (4)

No. 5J

REAR WALL PANEL (1)

No. 21J

DOOR TRACK (1)

No. 6J

DOOR JAMB (2)

No. 109J

ROOF COVER PANEL (1)

No. 419J

DOOR PANEL (2)

No. F23J

DOOR GLIDE (4)

No. A67

DOOR LATCH FINGER (1)

No. 10J

CORNER GUSSET (8)

No. 51J

SCREW CLIPS (16)

No. 85J

ROOF SUPPORT ARM

BRACKET (1)

No. 9J

ROOF COVER HINGE (2)

No. 55J ROOF CORNER CAP (4)

No. 60H

ROOF SUPPORT ARM (1)

No. 13J

ROOF EDGE TRIM (2)

No. 16J

(TOP & BOTTOM)

ROOF EDGE TRIM (2)

No. 17J (SIDES)

ROOF LATCH BRACKET (1)

No. 8J

ROOF SUPPORT ARM

LATCH PLATE (1)

No. 14J

ROOF COVER BRACE (SHORT) (2)

No. 40J

ROOF COVER BRACE (LONG) (1)

No. 1036M

Parts List

Assembly Part Part Quantity

Key No. Number Description in Carton

840H Rear Base Rail 1

6J Front Base Rail 1

3J Side Base Rail 2

5J Corner Panel 4

21J Rear Wall Panel 1

840H Rear Top Rail 1

3J Side Top Rail 2

6J Door Track 1

109J Door Jamb 2

F23J Door Panel 2

419J Roof Cover Panel 1

17J Roof Edge Trim (Sides) 2

16J Roof Edge Trim (Top & Bottom) 2

1036M Roof Cover Brace (Long) 1

40J Roof Cover Brace (Short) 2

13J Roof Support Arm 1

BT1 Weather Stripping (1/2"x3/8"x12') 1 Roll

Owner's Manual 1

51J Corner Gusset 8

DH10 Door Handle 2

P61 Plastic Washers 1

14J Roof Support Arm Latch Plate 1

Hardware Kit (Bolts, Nuts and Screws) 1

A67 Door Glide 4

10J Door Latch Finger 1

85J Screw Clips (12-122) 16

60H Roof Corner Cap 4

8J Roof Latch Bracket 1

55J Roof Cover Hinge 2

9J Roof Support Arm Bracket 1

A05

IMPORTANT...When ordering parts please provide number stamped on the surface of galvanized

parts. In the case of wall and roof panels please provide the model number of the building,

color and size of panels. To order parts please use order form on the last page.

Assemble rear base rail and front base

rail to side base rails with corner gussets

at each corner as shown… and place on

flat surface.

STEP

A06

Install 4 corner panels to base frame as shown…

Do not fasten panels to front base rail. Then install narrow rear wall panel in correct

position.

STEP

REAR PANEL

No. 21J

DOORWAY

USE SELF TAPPING SCREWS..10mm (3/8") LONG

CORNER PANEL

No. 5J

INSTALL PANELS IN

THIS SEQUENCE.

USE SELF TAPPING SCREWS...10mm (3/8") LONG

SIDE BASE RAIL

No. 3J

NOTE - LONG SLOT ON SIDE

FRONT BASE RAIL

No. 6J

USE 10mm (3/8") LONG

BOLTS AND NUTS

REAR BASE RAIL

No. 840H

CORNER

GUSSETS

No. 51J

ALL WALL PANELS ARE TO BE

ATTACHED TO TOP RAIL AND BASE

RAIL WITH SCREWS.

STEP

A07

CORNER GUSSET

No. 51J

SIDE TOP RAIL

No. 3J

(with Long Slot on Top)

1. Slide 4 door glides into door track (as shown).

STEP

SLIDE DOOR GLIDES INTO DOOR TRACK

INSIDE

OUTSIDE

No. A67

DOOR GLIDE

FRONT

IMPORTANT PLACE FRONT EDGE OF

DOOR TRACK WITH THESE HOLES

FACING THE OUTSIDE.

DOOR

TRACK

No. 6J

1. Install door track to front end of side rails

with front corner gussets as shown.

Fasten only in holes indicated.

STEP

5USE SELF TAPPING SCREWS

...10mm (3/8") LONG

CORNER GUSSET

No. 51J

NOTE

Do not fasten

corner panels to

door track at front.

DOOR TRACK

No. 6J

USE SELF TAPPING

SCREWS...10mm

(3/8") LONG

USE SELF TAPPING

SCREW...10mm

(3/8") LONG

1. Install rear top rail and fasten to wall panels.

2. Fasten side top rail to wall panels.

3. Install 2 rear corner gussets

and fasten only in holes indicated.

REAR TOP RAIL

No. 840H

USE 10mm (3/8") LONG

BOLT AND NUT

1. Carefully swing front section of corner panel away from door track. Position door jamb on side

of doorway. Then fasten top and bottom directly to door track and front base rail. See “A”.

2. Then swing corner panel back into position and fasten to door track and front base rail.

See “B” & “C”. Repeat for other side.

STEP

A08

CORNER PANEL

"A"

DOOR TRACK

DOOR JAMB (RIGHT)

No. 109J DOOR JAMB

(RIGHT) No. 109J

DOOR

TRACK

CORNER PANEL CORNER PANEL

"B" "C"

DOOR

TRACK

DOOR JAMB

(RIGHT) No. 109J

USE PLASTIC

WASHERS

STEP

VIEWED FROM

OUTSIDE BUILDING

USE 13mm (1/2")

LONG BOLTS AND NUTS

1. Inside and near the corner of build-

ing, install bottom lip of left door

into track formed in base rail.

2. Position top of door so that holes

in door line up with center holes in

door glide. Fasten inner door glide

(nearest to left door jamb) to door

using 10mm (3/8”) long bolts and

nuts. Position door latch finger

(10J) behind door panel and fas-

ten through outer door glide using

10mm (3/8”) bolts and nuts.

See “A”

3. Install right hand door in the same

manner but without the door latch

finger.

STEP

INSIDE

LEFT RIGHT

OUTSIDE

DOOR ADJUSTMENT

There are 3 holes in each of the

door glides to raise or lower

doors as required so that they

meet squarely

INSTALL DOOR INTO TRACK IN

BASE RAIL AND TILT

UP INTO PLACE

USE 10mm (3/8")

LONG BOLTS AND NUTS

INSIDE OF BUILDING

INSIDE VIEW LEFT

DOOR

ONLY

DOOR TRACK

OUTSIDE INSIDE

Door Latch Finger

NOTE - 2 GLIDES PER DOOR

OUTSIDE INSIDE

LEFT RIGHT

VIEWED

FROM

OUTSIDE

Door Handle

"B"

DOOR INSTALLATION

1. Attach door handle using

bolts as shown in “A”.

2. Install two 6mm (1/4”) bolts

and nuts with plastic washers

at bottom of each door panel.

See “B”.

"A"

1. Turn roof cover panel upside down… be sure hole pattern matches sketch…See “A”

below.

2. Install screw clips (85J) over edge of roof cover panel exactly as shown at the hole

positions indicated. See “C”.

1. With panel still upside down, position roof edge trim, 17J (with most holes facing upwards)

over sides of panel so that holes line up with screw clips. Fasten through roof cover panel

with screws and washers. NOTE: Leave the 2 holes, 1 on each side of the center ridge

– on the left hand side of the panel, open. See “A” below.

2. Position roof edge trim, 16J, (with most holes facing upwards) over ends of side trim. Line

up holes and with 22mm (7/8”) long bolts and washers, fasten corner caps to 4 corners

through top of roof cover panel.

Leave other holes open. See “B” and “C”.

STEP

“B”

No. 16J

ROOF

EDGE

TRIM

“B”

No. 16J

ROOF

EDGE

TRIM

USE SELF TAPPING SCREWS AND

WASHERS…10mm (3/8”) LONG

No. 17J

ROOF EDGE TRIM

(SIDES)

No. 16J

ROOF EDGE TRIM

(TOP & BOTTOM)

USE 22mm (7/8”) LONG

BOLTS AND NUTS

LEAVE

OPEN

"B" LEAVE OPEN

"C"

No. 60H

ROOF CORNER CAP

No. 419J

ROOF COVER PANEL

(UPSIDE DOWN)

A09

No. 60H

ROOF CORNER CAP

"C"

SCREW CLIP "C"

No. 85J

SCREW CLIP

"C"

"A"

LINE UP HOLES

LEAVE OPEN

"C"

SCREW CLIP

LINE UP HOLES

No. 17J

ROOF

EDGE

TRIM

“A” No. 17J

ROOF

EDGE

TRIM

“A”

1. Position roof cover brace (long) 1036M diagonally as shown to the underside of panel.

Fasten through top of panel into brace, at the 2 center holes only, using 10mm (3/8”) long

bolts and nuts with plastic washers.

2. Position roof cover braces (short) 40J, vertically over ends of diagonal brace (1036M) with

ends of each short brace under the lips of the top and bottom roof edge trim. Fasten through

top of roof cover panel with 10mm (3/8”) screws and plastic washers in center area only.

3. Fasten extreme end of braces (40J) where they pass under the roof edge trim (16J) with

22mm (7/8”) long bolts, nuts and plastic washers.

STEP

USE SELF TAPPING SCREWS

AND PLASTIC WASHERS…10mm

(3/8”) LONG IN CENTER AREA

USE 22mm (7/8”) LONG BOLTS

AND NUTS AT ENDS OF ROOF

COVER BRACES (SHORT) ROOF COVER BRACE

(LONG) No. 1036M

ROOF COVER BRACE

(SHORT) No. 40J

A10

1. Install roof latch bracket (8J) to top of roof cover with 10mm (3/8”) bolt and nut with plastic

washer and 22mm (7/8”) bolt and nut with plastic washer. See “A”. NOTE: Leave nuts

slack for later adjustments.

2. Tap into place screw clips over the 2 double holes in bottom roof trim (16J). Fasten roof

cover hinges (narrow side) to roof cover assembly as shown. See “B”.

3. Complete the securing of braces to roof by using 10mm (3/8”) and 22mm (7/8”) bolts and

nuts with plastic washers where required.

4. With help – fasten completed roof cover assembly to base unit by using 10mm (3/8”)

screws, through hinges into rear corner gussets and rear top rail. See “C”. NOTE:

For a stronger attachment, place screw clips (85J) under holes in rear top rail and

tightenscrews into clips.

STEP

X-SECTIONAL ASSEMBLY VIEW PLASTIC

WASHERS

USE 10mm (3/8")

BOLT AND NUT

USE 22mm (7/8")

BOLT AND NUT

USE SELF TAPPING SCREWS

10mm (3/8") LONG

WITH SCREW CLIPS

HINGE

ROOF EDGE TRIM

BOTTOM

USE SELF

TAPPING SCREWS

10mm (3/8") LONG

"C"

ROOF HINGE

No. 55J

"A"

"B"

1. Install roof support arm latch plate (14J) on left, top side rail (3J) with two 10mm (3/8”) screws

so that the slotted holes in each piece overlap as shown. See “A”

2. Assemble roof support arm (13J) and roof support arm bracket (9J) with a 10mm (3/8”) bolt

and locknut. Leave slack. See “B”

3. On the left side of roof, slide roof support arm bracket beneath roof edge trim so that its holes

line up with open holes in roof edge trim. Attach with 10mm (3/8”) long screws and plastic

washers. See “D”

4. Slide other end of support arm (13J) through slot in side top rail, so that notch in arm hooks

into the overlapped slot in top rail to support roof in the open position. Install bolt and nut

in bottom hole of arm.

See “C”

5. Cut self adhesive weatherstripping to length and apply to top rails, as shown in “E”.

6. Grease hinges.

7. With lid shut adjust roof latch bracket (8J) so that door latch finger (10J) on left hand door,

engages with roof latch bracket to lock lid. Tighten the 2 bolts that hold roof latch bracket

to roof.

8. Use large center holes in bottom gussets to anchor unit, if required.

STEP

SCREW CLIP

ROOF PANEL

ROOF SUPPORT

ARM BRACKET

"D"

PLASTIC WASHER

USE 10mm (3/8")

LONG SCREWS

SECTION OF 3J

X-SECTIONAL VIEW

LEAVE APPROX. 1/2"

WEATHERSTRIPPING

ROOF SUPPORT

ARM No. 13J

"C"

USE 10mm (3/8") BOLT

ROOF SUPPORT

ARM BRACKET

No. 9J

USE

10mm (3/8")

BOLT

LOCKNUT

"B"

WALL PANEL/REINFORCING RIB

TOP RAIL OR

DOOR TRACK

"E"

A11

ROOF

SUPPORT ARM

LATCH PLATE

No. 14J

"A"

REPLACEMENT PARTS OR ANY QUESTIONS REGARDING YOUR BUILDING SHOULD BE

REFERRED DIRECTLY TO THE FACTORY. DO NOT CONTACT YOUR DEALER, THEY

ARE NOT EQUIPPED TO SERVICE YOUR REQUESTS AS PROMPTLY AS THE

CUSTOMER SERVICE DEPARTMENT AT THE FACTORY (1-800-851-1085).

PARTS REPLACEMENT ORDER FORM

** MODEL NO.______________ **

PART NO. QTY. COLOR

FOR PARTS REPLACEMENT PLEASE CONTACT

CUSTOMER SERVICE DEPARTMENT.

TELEPHONE NO. (1-800-851-1085)

NAME:

ADDRESS:

CITY: PROVINCE/STATE:

POSTAL CODE/ZIP: TELEPHONE:

PURCHASED FROM:

STORE ADDRESS:

DATE PURCHASED:

A12

Parts Required

or Mail To: Spacemaker, Ltd.

3069 Wolfedale Road

Mississauga, Ontario L5C 1V9

Arrow STA42 Owner's manual

Arrow STA42 Owner's manual

Arrow STA42 Owner's manual

Related papers

Other documents