Miller MC490011G Owner's manual

Proheat Digital Recorder

Processes

Description

OM-222 096H 2012−09

Induction Heating

Single Induction Heating Power Source

Temperature Recorder

For Warranty Claims And Technical Support, Contact:

Sure Controls

N981 Tower View Drive

Greenville, WI 54942 USA

Tel 920-757-0500

[

Page is loading ...

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING 1..................................

1-1. Symbol Usage 1........................................................................

1-2. Induction Heating Hazards 1.............................................................

1-3. Additional Symbols for Installation, Operation, and Maintenance 2..............................

1-4. California Proposition 65 Warnings 3.......................................................

1-5. Principal Safety Standards 3.............................................................

1-6. EMF Information 3......................................................................

SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION 4............................

2-1. Signification des symboles 4.............................................................

2-2. Dangers relatifs au soudage à l’arc 4......................................................

2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance 5......

2-4. Proposition californienne 65 Avertissements 6...............................................

2-5. Principales normes de sécurité 6..........................................................

2-6. Informations relatives aux CEM 7.........................................................

SECTION 3 − DEFINITIONS 8...................................................................

3-1. Additional Safety Symbols And Definitions 8................................................

3-2. Miscellaneous Symbols And Definitions 9...................................................

SECTION 4 − INSTALLATION 10..................................................................

4-1. Serial Number And Rating Label Location 10.................................................

4-2. Specifications 10........................................................................

4-3. Recorder Installation 10...................................................................

4-4. Connecting To Power Source 11...........................................................

4-5. Output 14 Pin Information For Receptacle RC9 12............................................

SECTION 5 − SETUP AND OPERATION 13........................................................

5-1. Digital Recorder Controls 13...............................................................

5-2. Time Date Setup − Digital 13..............................................................

5-2-1. Login As Engineer 13..................................................................

5-2-2. Go To Operator Screen 13..............................................................

5-2-3. Locale Setup 13......................................................................

5-2-4. Time And Date Setup 13...............................................................

5-2-5. Login As User 14.....................................................................

5-2-6. Go To Home Screen 14................................................................

5-2-7. Channel Cycling On/Off And Notes 14....................................................

5-3. Operation 15............................................................................

5-3-1. Batch Recording Using Recorder 15.....................................................

5-3-1-1. Login As User 15..................................................................

5-3-1-2. Start Recording 15.................................................................

5-3-1-3. Stop Recording 15.................................................................

5-3-1-4. Saving Data To Media (Recommended After Each Batch) 16..............................

5-3-1-5. Saving Data To A PC (Alternative To Media) 16.........................................

5-3-1-5-1. Review Software − First Time Setup 16...........................................

5-3-1-5-2. Creating A Shortcut − First Time Setup 16.........................................

5-3-1-5-3. Changing IP Address To Connect The Recorder 17.................................

5-3-1-5-4. Downloading Files From Recorder 17.............................................

5-3-1-5-5. Troubleshooting Connection Problems 17.........................................

5-3-1-5-6. Resetting IP Address (Necessary To Connect User’s PC To Company’s Network) 17.....

5-3-2. Recovering From An Interruption 18......................................................

5-3-3. Viewing Data In QuickChart Software 18..................................................

5-3-3-1. Installing Software And First Time Setup 18............................................

5-3-3-2. Backing Up Data 20................................................................

5-3-4. Running QuickChart Software 20........................................................

5-4. Changing Recorder From Degrees F to Degrees C 31.........................................

TABLE OF CONTENTS

SECTION 6 − MAINTENANCE & TROUBLESHOOTING 35...........................................

6-1. Routine Maintenance 35..................................................................

6-2. Calibration Verification Equipment 35.......................................................

6-3. Calibration Verification Procedure 35........................................................

6-3-1. Initial Set Up 36.......................................................................

6-3-2. Getting Information From Recorder 36....................................................

6-3-3. Set Up Recorder For Verification 36......................................................

6-3-4. Calibration Verification 36..............................................................

6-3-5. Finishing Procedure 36................................................................

6-4. Replacing Recorder Battery 39............................................................

6-5. Troubleshooting 40......................................................................

6-6. Diagnostic Procedures For Recorder 40.....................................................

6-6-1. Recorder Does Not Turn On 40.........................................................

6-6-2. Recorder Displays Channel Error 40.....................................................

SECTION 7 − ELECTRICAL DIAGRAMS 41........................................................

SECTION 8 − PARTS LIST 42.....................................................................

WARRANTY

DECLARATION OF CONFORMITY

for European Community (CE marked) products.

MILLER Electric Mfg. Co., 1635 Spencer Street, Appleton, WI 54914 U.S.A. declares that the

product(s) identified in this declaration conform to the essential requirements and provisions of

the stated Council Directive(s) and Standard(s).

Product/Apparatus Identification:

Product Stock Number

RECORDER,DIGITAL 12 CHANNEL 300698

RECORDER,DIGITAL 6 CHANNEL 195374

Council Directives:

 2006/95/EC Low Voltage

 2004/108/EC Electromagnetic Compatibility

 2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic equipment

Standards:

 IEC 609741:2005 Arc welding equipment – Part 1: Welding power sources

 IEC 6097410:2007 Arc Welding Equipment – Part 10: Electromagnetic compatibility (EMC) requirements

 EN 50445:2008 Product family standard to demonstrate compliance of equipment for resistance welding,

arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic

fields (0 Hz – 300Hz)

Signatory:

_____________________________________ ___________________________________________

David A. Werba

Date of Declaration

MANAGER, PRODUCT DESIGN COMPLIANCE

October 8, 2012

203827C

Page is loading ...

OM-222 096 Page 1

SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING

ihom _2011-10

Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.

1-1. Symbol Usage

DANGER! − Indicates a hazardous situation which, if

not avoided, will result in death or serious injury. The

possible hazards are shown in the adjoining symbols

or explained in the text.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible

hazards are shown in the adjoining symbols or ex-

plained in the text.

NOTICE − Indicates statements not related to personal injury.

. Indicates special instructions.

This group of symbols means Warning! Watch Out! ELECTRIC

SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym-

bols and related instructions below for necessary actions to avoid the

hazards.

1-2. Induction Heating Hazards

The symbols shown below are used throughout this manual

to call attention to and identify possible hazards. When you

see the symbol, watch out, and follow the related instructions

to avoid the hazard. The safety information given below is

only a summary of the more complete safety information

found in the Safety Standards listed in Section 1-5. Read and

follow all Safety Standards.

Only qualified persons should install, operate, maintain, and

repair this unit.

During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The power circuit and output bus

bars or connections are electrically live whenever

the output is on. The input power circuit and machine

internal circuits are also live when power is on. Incorrectly installed or

improperly grounded equipment is a hazard.

D Do not touch live electrical parts.

D Enclose any connecting bus bars and coolant fittings to prevent

unintentional contact.

D Wear dry, hole-free insulating gloves and body protection.

D Insulate yourself from work and ground using dry insulating mats or

covers big enough to prevent any physical contact with the work or

ground.

D Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp locations

or while wearing wet clothing; on metal structures such as floors,

gratings, or scaffolds; when in cramped positions such as sitting,

kneeling, or lying; or when there is a high risk of unavoidable or ac-

cidental contact with the workpiece or ground. For these

conditions, see ANSI Z49.1 listed in Safety Standards. And, do not

work alone!

D Disconnect input power before installing or servicing this equip-

ment. Lockout/tagout input power according to OSHA 29 CFR

1910.147 (see Safety Standards).

D Use only nonconductive coolant hoses with a minimum length of 18

inches (457 mm) to provide isolation.

D Properly install, ground, and operate this equipment according to its

Owner’s Manual and national, state, and local codes.

D Always verify the supply ground − check and be sure that input pow-

er cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly grounded

receptacle outlet.

D When making input connections, attach proper grounding

conductor first − double-check connections.

D Keep cords dry, free of oil and grease, and protected from hot metal

and sparks.

D Frequently inspect input power cord for damage or bare wiring − re-

place cord immediately if damaged − bare wiring can kill.

D Turn off all equipment when not in use.

D Do not use worn, damaged, undersized, or poorly spliced cables.

D Do not drape cables over your body.

D Do not touch power circuit if you are in contact with the work, ground,

or another power circuit from a different machine.

D Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

D Wear a safety harness if working above floor level.

D Keep all panels and covers securely in place.

SIGNIFICANT DC VOLTAGE exists in inverter power

sources AFTER removal of input power.

D Turn Off inverter, disconnect input power, and discharge input

capacitors according to instructions in Maintenance Section before

touching any internal parts.

Induction Heating of certain materials, adhesives,

and fluxes can produce fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

FUMES AND GASES can be hazardous.

D Keep your head out of the fumes. Do not breathe the fumes.

D If inside, ventilate the area and/or use local forced ventilation to re-

move fumes and gases.

D If ventilation is poor, wear an approved air-supplied respirator.

D Read and understand the Material Safety Data Sheets (MSDSs)

and the manufacturer’s instruction for adhesives, fluxes, metals,

consumables, coatings, cleaners, and degreasers.

D Work in a confined space only if it is well ventilated, or while wearing

an air-supplied respirator. Always have a trained watchperson near-

by. Fumes and gases from heating can displace air and lower the

oxygen level causing injury or death. Be sure the breathing air is

safe.

D Do not heat in locations near degreasing, cleaning, or spraying oper-

ations. The heat can react with vapors to form highly toxic and

irritating gases.

D Do not overheat coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the

heated area, the area is well ventilated, and while wearing an air-

supplied respirator. The coatings and any metals containing these

elements can give off toxic fumes if overheated. See coating MSDS

for temperature information.

OM-222 096 Page 2

FIRE OR EXPLOSION hazard.

D Do not overheat parts.

D Watch for fire; keep extinguisher nearby.

D Keep flammables away from work area.

D Do not locate unit on, over, or near combustible surfaces.

D Do not install unit near flammables.

D Do not operate where the atmosphere may contain flammable

dust, gas, or liquid vapors (such as gasoline).

D After completion of work, inspect area to ensure it is free of

sparks, glowing embers, and flames.

D Use only correct fuses or circuit breakers. Do not oversize or by-

pass them.

INDUCTION HEATING can burn.

D Do not touch hot parts bare-handed.

D Allow cooling period before handling parts or

equipment.

D Do not touch or handle induction head/coil

during operation.

D Keep metal jewelry and other metal personal items away from

head/coil during operation.

D To handle hot parts, use proper tools and/or wear heavy, insu-

lated welding gloves and clothing to prevent burns.

1-3. Additional Symbols for Installation, Operation, and Maintenance

FALLING EQUIPMENT can injure.

D Use handle and have person of adequate

physical strength lift unit.

D Move unit with hand cart or similar device.

D For units without a handle, use equipment of

adequate capacity to lift and support unit.

D Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

D If using lift forks to move unit, be sure forks are long enough to

extend beyond opposite side of unit.

D Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94−110) when manu-

ally lifting heavy parts or equipment.

FLYING METAL OR DIRT can injure eyes.

D Wear approved safety glasses with side

shields or wear face shield.

MOVING PARTS can injure.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards

closed and securely in place.

D Have only qualified persons remove doors, panels, covers, or

guards for maintenance and troubleshooting as necessary.

D Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

ELECTRIC AND MAGNETIC FIELDS (EMF)

can affect Implanted Medical Devices.

D Wearers of Pacemakers and other Implanted

Medical Devices should keep away.

D Implanted Medical Device wearers should consult their doctor

and the device manufacturer before going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating

operations.

OVERUSE can cause OVERHEATING

D Allow cooling period.

D Reduce output or reduce duty cycle before

starting to heat again.

D Follow rated duty cycle.

STATIC (ESD) can damage PC boards.

D Put on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to

store, move, or ship PC boards.

H.F. RADIATION can cause interference.

D High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

D Have only qualified person familiar with electronic equipment per-

form this installation.

D The user is responsible for having a qualified electrician promptly

correct any interference problem resulting from the installation.

D If notified by the FCC about interference, stop using the equip-

ment at once.

D Have the installation regularly checked and maintained.

D Keep high-frequency source doors and panels tightly shut.

READ INSTRUCTIONS.

D Read and follow all labels and the Owner’s

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

D Use only genuine replacement parts from the manufacturer.

D Perform maintenance and service according to the Owner’s

Manuals, industry standards, and national, state, and local

codes.

BATTERY EXPLOSION can injure.

D Do not use induction equipment to charge bat-

teries or jump start vehicles unless it has a bat-

tery charging feature designed for this purpose.

OM-222 096 Page 3

1-4. California Proposition 65 Warnings

Welding or cutting equipment produces fumes or gases

which contain chemicals known to the State of California to

cause birth defects and, in some cases, cancer. (California

Health & Safety Code Section 25249.5 et seq.)

This product contains chemicals, including lead, known to the

state of California to cause cancer, birth defects, or other re-

productive harm. Wash hands after use.

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

is available as a free download from the American Welding Society at

http://www.aws.org or purchased from Global Engineering Documents

(phone: 1-877-413-5184, website: www.global.ihs.com).

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2, from Canadian Standards Association, Standards Sales, 5060

Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:

800-463-6727, website: www.csa-international.org).

OSHA, Occupational Safety and Health Standards for General Industry,

Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and

Part 1926, Subpart J, from U.S. Government Printing Office, Superinten-

dent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954

(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—phone

for Region 5, Chicago, is 312-353-2220, website: www.osha.gov).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:

www.nfpa.org and www. sparky.org).

Canadian Electrical Code Part 1, CSA Standard C22.1, from Canadian

Standards Association, Standards Sales, 5060 Spectrum Way, Suite

100, Mississauga, Ontario, Canada L4W 5NS (phone: 800-463-6727,

website: www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, from American National Standards Institute,

25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-

site: www.ansi.org).

Applications Manual for the Revised NIOSH Lifting Equation, The Na-

tional Institute for Occupational Safety and Health (NIOSH), 1600 Clifton

Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website: www.cdc.gov/

NIOSH).

1-6. EMF Information

Electric current flowing through any conductor causes localized electric

and magnetic fields (EMF). Welding current creates an EMF field around

the welding circuit and welding equipment. EMF fields may interfere with

some medical implants, e.g. pacemakers. Protective measures for per-

sons wearing medical implants have to be taken. For example, restrict

access for passers−by or conduct individual risk assessment for weld-

ers. All welders should use the following procedures in order to minimize

exposure to EMF fields from the welding circuit:

1. Keep cables close together by twisting or taping them, or using a

cable cover.

2. Do not place your body between welding cables. Arrange cables

to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep head and trunk as far away from the equipment in the weld-

ing circuit as possible.

5. Connect work clamp to workpiece as close to the weld as

possible.

6. Do not work next to, sit or lean on the welding power source.

7. Do not weld whilst carrying the welding power source or wire

feeder.

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the

device manufacturer before performing or going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating operations. If

cleared by your doctor, then following the above procedures is recom-

mended.

Page is loading ...

OM-222 096 Page 6

L’EMPLOI EXCESSIF peut SUR-

CHAUFFER L’ÉQUIPEMENT.

D Prévoir une période de refroidissement

D Réduire le courant de sortie ou le facteur de mar-

che avant de recommencer le chauffage.

D Respecter le cycle opératoire nominal.

LES CHARGES ÉLECTROSTATIQUES

peuvent endommager les circuits im-

primés.

D Établir la connexion avec la barrette de terre

AVANT de manipuler des cartes ou des pièces.

D Utiliser des pochettes et des boîtes antistati-

ques pour stocker, déplacer ou expédier des

cartes PC.

LE RAYONNEMENT HAUTE FRÉ-

QUENCE (HF) risque de provoquer

des interférences.

D Le rayonnement haute fréquence (HF) peut

provoquer des interférences avec les équipe-

ments de radio-navigation et de communication,

les services de sécurité et les ordinateurs.

D Demander seulement à des personnes qualifiées familiarisées

avec des équipements électroniques de faire fonctionner l’installa-

tion.

D L’utilisateur est tenu de faire corriger rapidement par un électricien

qualifié les interférences résultant de l’installation.

D Si le FCC signale des interférences, arrêter immédiatement l’appa-

reil.

D Effectuer régulièrement le contrôle et l’entretien de l’installation.

D Maintenir soigneusement fermés les portes et les panneaux des

sources de haute fréquence.

LIRE LES INSTRUCTIONS.

D Lire et appliquer les instructions sur les

étiquettes et le Mode d’emploi avant

l’installation, l’utilisation ou l’entretien de

l’appareil. Lire les informations de sécurité au

début du manuel et dans chaque section.

D N’utiliser que les pièces de rechange recommandées par le

constructeur.

D Effectuer l’entretien en respectant les manuels d’utilisation,

les normes industrielles et les codes nationaux, d’état et locaux.

L’EXPLOSION DE LA BATTERIE

peut provoquer des blessures.

D Ne pas utiliser l’appareil de soudage pour

charger des batteries ou faire démarrer

des véhicules à l’aide de câbles de démarrage,

sauf si l’appareil dispose d’une fonctionnalité

de charge de batterie destinée à cet usage.

2-4. Proposition californienne 65 Avertissements

Les équipements de soudage et de coupage produisent des

fumées et des gaz qui contiennent des produits chimiques

dont l’État de Californie reconnaît qu’ils provoquent des mal-

formations congénitales et, dans certains cas, des cancers.

(Code de santé et de sécurité de Californie, chapitre 25249.5

et suivants).

Ce produit contient des éléments chimiques, dont le plomb,

reconnus par l’État de Californie pour leur caractère

cancérogène ainsi que provoquant des malformations

congénitales ou autres problèmes de procréation. Se laver les

mains après toute manipulation.

2-5. Principales normes de sécurité

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

from Global Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).