BLADE™
Setup Guide
This guide provides information about how to
prepare the site and install the BLADE.
Read completely before you begin.
IMPORTANT
READ FIRST
2BLADE Setup Guide
Location
• Provides a designated area with a sturdy, non-ammable workbench capable of supporting at least the weight of the unit
• The BLADE without racks weighs 130 lbs (59 kg)
• Area is free from vibration of large equipment
• Minimum counter space: 35 in (88.9 cm) W x 25 in (63.5 cm) D x 29.5 in (75 cm) H
• BLADE Dimensions: 19 in (48.3 cm) W x 24 in (61 cm) D x 29.5 in (75 cm) H
• The above provides 8” (20 cm) of open space on each side and 1” (2.6 cm) open space behind the instrument for
proper ventilation.
• System exhaust connection exits top of unit. Shelves or cabinetry above unit is not recommended.
• Allows for easy access to the fume cabinet and room for the door to extend fully at 16.5” (42 cm)
• Provides adequate space for sample handling
• Provides clear visual access to the display of the system
• Adequate exhaust that pulls a minimum of 125 CFM at point of connection
• DO NOT install in a fume hood
• DO NOT place items on top of the instrument
• DO NOT position unit such that it is difcult to access the power cord receptacle. The power cord receptacle must be
readily accessible for disconnection if needed.
Environmental Conditions
• Indoor use only
• Altitude up to 2000 m
• A Temperature range of 41 °F (5 °C) to 104 °F (40 °C)
• Relative humidity range of 10% to 85%, non-condensing
• Overvoltage Category II
• Pollution degree 2
Electrical Requirements
• Region Specic
• 120 VAC, 50/60 Hz, 15 A
• 200 VAC, 50/60 Hz, 10 A
• 240 VAC, 50/60 Hz, 10 A
• Line voltage must not vary more than 10% of its specied level
• Dedicated, grounded outlet no more than 8 feet (2.5 M) from unit
• Instrument is supplied with a region specic power cord or an adequately rated power cord may be used
WARNING
DO NOT install an instrument in a site that does not meet the criteria below. PROCEED ONLY after you
have prepared your site.
General Site Preparation
3BLADE Setup Guide
Figure 1
Figure 2
Figure 3
1. View the Site Preparation Guide (P/N FM0082) or “System Specications”
section of this manual and select a location that meets requirements be-
fore installing the BLADE instrument.
2. Carefully inspect the shipping carton, the instrument, and accessories for
any damage that may have occurred during shipping. If the instrument or
accessories have damage, contact the freight carrier to report the damage
and le a damage report. Contact your CEM Representative for assistance.
3. Pull plastic tab, swing handle open, and remove the plastic clip from the
box. Repeat process on the remaining handles. (Figure 1)
4. Use handles to pull up and remove outer box. (Figure 2)
5. Carefully cut the tape on both sides of the inner box and lay the sides of
the box at.
6. Remove the foam from the top of the system.
7. Open the plastic surround the instrument to allow access to the instru-
ment. DO NOT leave the plastic under the system. (Figure 3)
8. Using two people, locate the cutouts in the foam on the sides of the instru-
ment and lift onto the bench top near exhaust service. DO NOT place the
system in a fume hood.
WARNING
To avoid muscle strain or back injury, use lifting aids and
proper lifting techniques when removing or replacing.
DO NOT install the BLADE instrument inside of a fume
hood.
Unboxing
4BLADE Setup Guide
1. Connect the exhaust hose as outlined below. (Figure 4)
WARNING
The exhaust hose must be connected and draw at least
125 CFM at the point of connection at all times as it
is essential for removing harmful vapors away from the
instrument. Vapors should be vented into a fume hood by
means of the exhaust hose only.
1.1. Locate the exhaust hose and the hose clamp in the accessory kit.
1.2. Place the hose clamp onto the exhaust port located at the top of
the BLADE.
1.3. Connect one end of the hose to the exhaust port.
1.4. Press the exhaust hose all the way down onto the port and then
use the hose clamp to tighten the hose onto the exhaust port.
1.5. Connect the opposite end of the exhaust hose to a fume hood
that pulls a minimum of 125 CFM at point of connection using the
provided clamp if necessary.
1.6. In the rare event of condensation forming in the exhaust, a drain
line can be connected by installing user supplied parts.
2. Install the correct fuses as outlined below. (Figure 5)
2.1. Remove the two (2) fuse holders from the back of the instrument
by twisting counter clockwise.
2.2. Locate the correct fuses inside the accessory kit.
• 120 VAC: 15 A fuse (F15AH250V)
• 200 & 240 VAC: 10 A fuse (F10AH250V)
WARNING
Incorrect fuse size may result in re or inadequate
equipment protection.
15 A fuse (F15AH250V): 120 VAC
10 A fuse (F10AH250V): 200 & 240 VAC
2.3. Install the supplied fuses into the fuse holders.
2.4. Install the fuse and holders into the instrument and twist clock-
wise until tight.
3. Plug the power cord into the back of the instrument and into a dedicated,
grounded outlet. The instrument is supplied with a power cord, but an ade-
quately rated power cord may be used.
4. Connect the barcode scanner by installing the USB connector into one of
the USB ports. (Figure 6)
Figure 4
Figure 5
Figure 6
Hardware Setup
5BLADE Setup Guide
Software Setup
1. With the instrument facing forward, position the power switch to ON. Make sure the power switch can easily be ac-
cessed. DO NOT REMOVE any packing material until instructed to do so.
2. Remove the blue tape from the door and interlock cover.
3. Follow the instructions on the BLADE display once the system is powered on to remove the packing foam within the
fume cabinet. DO NOT REMOVE any packing material until instructed to do so. Retain all packing material for use if
returning the instrument.
4. Remove the blue tape from the exhaust cover.
5. Perform an “Exhaust Validation” test to determine if adequate exhaust is achievable.
5.1. Press the System Menu icon located in the top right corner of the screen.
5.2. Press “Tools” and the “Utilities” tab.
5.3. Locate “Exhaust Validation” and press “Start.”
5.4. Follow instructions located on the screen to complete verication.
5.5. If any of the validation points result in a red “X,” verify that the exhaust requirements have been met and view
the BLADE manual (P/N 601477).
WARNING
DO NOT attempt unit operation if the “Exhaust Validation” test results in a red “X.”
6. Perform an “Autosampler Validation” test to verify pre-determined rack positions and the attenuator.
6.1. Press the System Menu icon located in the top right corner of the screen.
6.2. Press “Tools” and the “Utilities” tab.
6.3. Locate Autosampler and press “Validate.”
6.4. Follow instructions located on the screen to complete calibration.
6.5. If the validation fails, perform an Autosampler Calibration as outlined in the “Calibrations” section of the manu-
al (P/N 601477).
7. Scan the barcode located on the Cap Assembly box which includes the caps and septa as outlined below.
7.1. Ensure that the barcode scanner is connected to the BLADE.
7.2. Locate the box containing the cap and septa.
7.3. Press the System Menu icon in the top right corner of the display.
7.4. Press “Settings” and then press the Run tab.
7.5. Press the barcode icon.
7.6. Use the barcode scanner to scan the barcode on the cap and septa box or the numerical number located be-
neath the barcode can be manually entered. This code can only be used once.
7.7. Press “OK.” The cap count in the settings will increase by 250.
8. Perform a “QC Test”. View the “QC Test” method notes for details regarding sample preparation and the “Perform a
Digestion” section of the manual (P/N 601477) for details about vessel assembly, loading and performing the method.
9. Watch instructional videos found within the BLADE software as outlined below to customize system and user settings.
9.1. Press the System Menu icon in the top right corner of the screen.
9.2. Press “Video.”
10. Read and fully understand the BLADE manual (P/N 601477) before operating the instrument.
11. System setup complete. The BLADE is ready for operation.
601476 v1
10/22
© CEM Corporation. All Rights Reserved.
CEM® is a registered trademark of CEM Corporation.
BLADE and SMC are a trademark of CEM Corporation.
Contact Information
CEM Corporation Headquarters
Toll-Free Phone (US/Canada): (800) 726-3331
Phone: (704) 821-7015
Service Hotline: (800) 726-5551
Fax: (704) 821-7894
Mailing Address: PO Box 200 Matthews, NC 28106-0200
Physical Address: 3100 Smith Farm Rd Matthews, NC
28106
Email (Applications Support): elemental.support@cem.
com
Email (Technical Support): elemental.suppor[email protected]
CEM International Subsidiaries
France: CEM mWaves S.A.S.
Phone: (33-1) 69 35 57 80
Fax: (33-1) 60 19 64 91
Address: Immeuble Ariane Domaine Technologique de
Saclay 4, rue René Razel 91892 ORSAY Cedex France
Web Address: http://www.cemfrance.fr
Email: [email protected]
Germany: CEM GmbH
Phone: 011-49-2842-9644-0
Fax: 011-49-2842-9644-11
Address: Carl-Friedrich-GauB-Str. 9 47475 Kamp-Lintfort
Germany
Web Address: http://www.cem.de
Email: [email protected]
Italy: CEM SRL
Phone: 390-35-896224
Fax: 390-35-891661
Address: Via Dell Artigianato, 6/8 24055 Cologno Al
Serio (BG) Italy
Web Address: https://cem.com/it
Email: [email protected]
Japan: CEM Japan K.K.
Phone: +81-3-5793-8542
Fax: +81-3-5793-8543
Address: 2-18-10 Takanawa Minato-Ku Tokyo 108-0074
Japan
Web Address: http://www.cemjapan.co.jp
Email: [email protected]
UK: CEM Microwave Technology Ltd.
Phone: +44-1-280-822873
Fax: +44-1-280-822342
Address: 2 Middle Slade Buckingham Industrial Park
MK18 1WA Buckingham Great Britain
Web Address: http://www.cemmicrowave.co.uk
Email: [email protected]
Ireland: CEM Technology (Ireland) Ltd.
Phone: +353 (0) 1 885-1752
Address: Sky Business Centre 9a Plato Business Park
Damastown Dublin 15 Ireland
Web Address: http://www.cemmicrowave.co.uk
Email: [email protected]
CEM Distributors
For a complete list of distributors of CEM products,
including contact information, go to the CEM website
(http://www.cem.com), select Contact, and then select
your region to see a list of distributors by country.
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
PerkinElmer OPTIMA 8000 Customer Hardware And Service Manual
-
Varian ARCHON User manual
-
-
-
Oracle StorageTek SL3000 User manual
-
Distek 2500 Select Operating instructions
-
Hach ANATEL PAT700 User manual
-
-
Miller FILTAIR INDUSTRIAL COLLECTOR SERIES (230 VOLT) Owner's manual
-
