Johnson Controls FS-1300 User manual

Brand: Johnson Controls

Model: FS-1300

Category: Power extensions

Type: User manual

Johnson Controls FS-1300 is a Combination Fire and Smoke leakage-rated damper, which has been tested and approved as a matched set rated for 350 degrees Fahrenheit temperature degradation. Here is some product information that may be of use to you:

UL File No.

UL File No.

Damper and Actuator Product Guide 268.1

Fire/Smoke Section

Product Bulletin FS-1300

Issue Date 0499

Code No. LIT-2681190 www.johnsoncontrols.com

Since 1915, Johnson Controls has provided

high-quality dampers that fit customer size and

application requirements. Continuing the legacy, a

fire-and-leakage-rated damper for dynamic life safety

smoke management and fire-resistant systems, that

meets new UL leakage-testing procedures, is now

offered.

•

UL File No. R11172

•

CSFM3230-0554:128

•

1-1/2 Hour Fire Rating

•

Class II leakage resistance

These UL/cUL leakage-rated FS-1300 Combination

Fire/Smoke Dampers are listed under

UL Standard 555, fifth edition, dated May 31, 1995,

and under UL Standard 555S, second edition, dated

November 1993, including all paragraphs effective

May 1995 and California State Fire Marshal listed.

All FS-1300 Combination Fire/Smoke Dampers include

2-position electric or pneumatic actuators that have

been tested and approved as a matched set rated for

350°F temperature degradation

Figure 1: FS-1300 Combination Fire/Smoke Damper

Features and Benefits

❑

High-Torque Spring

Ensures closure during dynamic airflow and

acts as the latch with additional torque to keep

blades closed

❑

3-Year Warranty on

Materials and Workmanship

Confidence of company standing behind

product

❑

Dual Linkage Standard

Ensures complete rotation of all blades

❑

Sensor Temperature

Combinations of 165°F and

250°F (74°C and 121°C) or

212°F and 350°F (100°C and

177°C)

Combinations of heat-sensing devices to meet

job requirements

❑

16-Gauge Galvanized Steel

Blades

One blade profile provides the correct product

performance

FS-1300 Combination Fire/Smoke Dampers

1-1/2 Hour/Class II Leakage

FS-1300 Combination Fire/Smoke Dampers Product Bulletin

pplications

The FS-1300 Combination Fire/Smoke Damper is

designed to meet design specifications requiring one

damper to provide both a 1-1/2 hour fire rating and a

Class II leakage-rating at 350

The FS-1300 Combination Fire/Smoke Damper is

tested according to UL Standard 555 for dampers

intended for use in HVAC duct systems passing

through fire-resistive partitions, and UL Standard 555S

for dampers that are used in HVAC smoke systems.

When multiple assemblies incorporate individual

sections operated by their own closure mechanism or

actuator, each individual section is to be operated at

the maximum specified airflow for the multiple

assembly, with all other sections closed.

The FS-1300 Combination Fire/Smoke Damper must be

installed in accordance with the Standard

NFPA-90A

and

SMACNA Fire Damper Guide

, at the point where a

duct passes through a required fire barrier. The blades,

when closed, shall be within the plane of the fire barrier

(wall or floor).

The standard FS-1300 Combination Fire/Smoke

Damper includes a 24-inch-long, 18-gauge galvanized

steel sleeve, 165°F primary heat sensor, 250°F fusible

link, actuator, and dual linkage.

212°F primary heat sensor and 350°F fusible link are

optional.

Single-section dampers are approved for the following:

Figure 2: Wall Mounting

FS-1300 Combination Fire/Smoke Dampers, up to

32 inches wide x 48 inches high, are rated for

mounting in masonry or metal stud gypsum wallboard

fire-rated walls.

Figure 3: Floor/Ceiling Mounting

FS-1300 Combination Fire/Smoke Leakage-rated

Dampers, up to 32 inches wide x 36 inches high, are

rated for mounting in cement floors or ceilings.

aintenance

Johnson Controls FS-1300 Dampers have no

components that require routine scheduled maintenance.

uide Specification

Furnish and install Johnson Controls FS-1300

dynamically tested, multi-blade, 1-1/2 hour fire-rated

and Class II leakage-rated dampers, approved under

UL Standard 555 and UL Standard 555S, dated

May 1995 and California State Fire Marshal listed.

Primary

heat sensor shall respond at 165°F or 212°F

to remove power to an electric or pneumatic actuator

and to close the damper blades for smoke protection.

Fusible Link

with high-torque spring releasing at

either 250°F or 350°F shall be used to close the

damper blades and lock them closed for fire protection.

Frames

are to be constructed of formed, 13-gauge

galvanized sheet steel, with concealed linkage in both

side channels to provide positive blade motion and

eliminate noise and friction within the airstream.

Compressible spring stainless steel side seals and

bronze bearings shall be provided.

Blades

are to be constructed with 16-gauge

galvanized steel, and blade width not exceeding

8 inches. Blades shall have 3/8-inch square steel

zinc-plated pins.

FS-1300 Combination Fire/Smoke Dampers Product Bulletin

peration

After installation, when power (electric or pneumatic) is

applied to the actuator, the damper blades will be

driven to the open position by the actuator.

When the primary temperature sensor detects heat, it

breaks power to the actuator, closing the damper

blades through the spring-return mechanism of the

actuator. The damper is now in the smoke protection

mode (damper closed via actuator).

If the air temperature reaches the fusible link

temperature (secondary temperature sensor), the link

fuses. The damper linkage disengages from the

actuator, allowing the blades to close by a torsion

spring. The damper is now in fire protection mode

(damper closed via torsion spring) and further

operation is not possible.

onstruction

Primary

Temperature

Sensor

Factory-installed

Angle

Sleeve

Fusible Link

and Spring

Jackshaft

Linkage

Actuator

Figure 4: Damper Components

Table 1: Damper Construction

Component Description

Frame

13-gauge galvanized steel,

mechanically joined

Blades

16-gauge galvanized steel

Linkage

1/8 inch rolled steel, zinc plated,

concealed in both channels of the frame

Blade Pin

3/8 inch square steel, zinc plated

Bearings

Oil-impregnated bronze

Side Seal

Self-compensating stainless steel

Blade Seal

Stainless steel with extruded silicone

Sleeve

18-gauge galvanized sheet metal,

24-inches-long standard

Angles

16-gauge galvanized steel,

1.5 inch x 1.5 inch

Notes: The sleeve is designed for use with standard

breakaway connectors.

Mounting angles are provided with the damper. The

side containing factory-installed hardware has an

angle mounted as a guide for remaining angles on

that side.

abeling

All damper assemblies include an identification label,

which provides the following information:

•

damper model and size

•

manufacturing date code (year/week)

•

air leaving side

Other labels include:

•

intended mounting position

•

UL/cUL classification of damper

•

temperature rating

•

top of damper

•

direction of airflow

•

maximum rated airflow and static pressure

FS-1300 Combination Fire/Smoke Dampers Product Bulletin

ctuators

All actuators are factory mounted and tested with the

damper prior to shipment.

Electric

FS-1300 Combination Fire/Smoke Dampers are

available with Johnson Controls UL Listed/

CSA Certified electric actuators; 120 VAC actuator is

standard. Other actuator options are available.

Table 2: Electric Actuator

Code Number Description Maximum

Damper

Area

DMPR-S60024

60 lb·in, 24 VAC

DMPR-S60024S

60 lb·in, 24 VAC

w/auxiliary switch 16 sq ft

DMPR-S60120

60 lb·in, 120 VAC

DMPR-S60120S

60 lb·in, 120 VAC

w/auxiliary switch

Note: Maximum size and area limitations are determined

by UL testing. Future testing may include additional

actuators, or expand present limits.

For more detailed information on the electric actuator,

refer to the

High Temperature Electric Actuator for

Smoke Dampers Submittal Data

in the

Damper and

Actuator Product Guide (FAN 268.1

Pneumatic

FS-1300 Combination Fire/Smoke Dampers are

available with Johnson Controls UL Component

Recognized pneumatic actuators.

Table 3: Pneumatic Actuator

Actuator Maximum

Damper

Area

Maximum

Size

Temperature

DS-3153-2

25.3 sq ft 32 x 48 in. 350°F

Note: Maximum size and area limitations are a function of

past UL testing. Future testing may include

additional actuators, or expand present limits.

For more detailed information on the pneumatic

actuators, refer to the

DS-3153 Pneumatic Actuator

Product Bulletin

in the

Damper and Actuator Product

Guide (FAN 268.1)

izing

Table 4: Damper Size Limits

Size Limits

Width, in. Height, in.

Minimum

15 14

Maximum Single Panel

32 48

Damper Maximum

(Wall Installation)

64 96

Damper Maximum,

(Floor Installation)

64 72

FS-1300 size limits are a function of past UL tests.

Note: All FS-1300 Combination Fire/Smoke

Dampers will be provided with an actuator

from either Table 2 or 3, determined by the

fifth character in the code.

FS-1300 Combination Fire/Smoke Dampers are

available in nominal 1-inch increments only. Actual

damper size is 0.99479 inch less than nominal.

Note: Proper sleeve length is determined by adding

18 inches to the wall or floor thickness.

For example, a 6-inch fire wall would require a

24-inch-long minimum sleeve.

imensional Data

3.5

4.5, 8.5,

or 12.5

Width

Figure 5: Mounting Dimensions with

Electric Actuator, inches

FS-1300 Combination Fire/Smoke Dampers Product Bulletin

3.5

4.5, 8.5,

or 12.5

Width

Figure 6: Mounting Dimensions with

Pneumatic Actuator, inches

election Information

1. Determine required size and type of damper.

2. Select the features from

Table 5: FS-1300

Combination Fire/Smoke Damper Ordering

Template

that match the operation and

performance required.

3. Enter width and height of damper.

Note: To find actual damper size, multiply the

nominal size by 0.99479.

4. Enter options required.

FS-1300 Combination Fire/Smoke Dampers include

opposed 16-gauge blades, bronze bearings, side

seals, and dual linkage.

Example

TOVLE-200 x 200X is a combination

fire/smoke damper that has 16-gauge blades, opposed

blade operation, dual linkage, bronze bearings,

high-temperature blade seals, and side seals. Its

dimensions are 20 inches wide x 20 inches high, with a

24-inch-long sleeve, 24 VAC electric actuator, 165°F

primary heat sensor, and 250°F fusible link. (Unless

otherwise ordered, the system defaults to a

24-inch-long sleeve.)

Table 5: FS-1300 Combination Fire/Smoke Damper Ordering Template

Ordering Code Number TOV -0x0

Application

T = Fire/Smoke

Blade Operation

O = Opposed

Blade Type

V = 16-gauge

Bearing/Seal Type

L = 165°F Primary Sensor/250°F Fusible Link

H = 212°F Primary Sensor/350°F Fusible Link

Actuator Type

E = Electric

P = Pneumatic

Width Dimensions

15 to 64, 1 inch increments

Height Dimensions

14 to 96, 1 inch increments

Factory-installed

Options

Refer to Table 6 for selection and

combinations.

Note: Actual damper size is 0.99479 less than nominal. For example a damper ordered 24 inches wide x 32 inches high will

be shipped 23-7/8 inches wide x 31-27/32 inches high.

ptions

Table 6: Option List

Code Option Description

Pilot Positioner (cannot be used with options X, Y, and Z)

32-inch-long Sleeve

Left-side Actuator Mounting

24 VAC Electric Actuator (cannot be used with options P, Y, and Z)

120 VAC Electric Actuator with Switches (cannot be used with options P, X, and Z)

24 VAC Electric Actuator with Switches (cannot be used with options P, X, and Y)

Note: Limit of two factory-installed options.

FS-1300 Combination Fire/Smoke Dampers Product Bulletin

echnical Data

100

0.00

0.01

0.10

1.00

Approach Velocity (fpm x 100)

Static Pressure (inches W.C.)

Figure 7: Pressure Drop Curve,

24 x 24 inch Damper

100

1.00

Leakage Rate (cfm/sq ft)

Static Pressure (inches W.C.)

10.00

Figure 8: Leakage Curve

Table 7: Damper Weights, lb (kg)

Height,

Width, in. (cm)

in. (cm) 10 (25) 18 (46) 26 (66) 32 (81)

10 (25)

24 (10.9) 27 (12.2) 30 (13.6) 33 (15)

18 (46)

27 (12.2) 32 (14.5) 37 (16.8) 39 (17.7)

26 (66)

29 (13.1) 36 (16.3) 44 (20.0) 46 (20.9)

34 (86)

31 (14.1) 40 (18.1) 50 (22.7) 60 (27.2)

42 (107)

34 (15.4) 44 (20.0) 55 (25.0) 65 (29.5)

48 (122)

37 (16.8) 53 (24.0) 61 (27.7) 67 (30.4)

Note: Weight includes actuator, fusible link, spring, and

mounting hardware, and does not include the weight

of sleeve material or shipping crate.

FS-1300 Combination Fire/Smoke Dampers Product Bulletin

Table 8: FS-1300 Dynamic Rating - Electric Actuator

Width x Height, in. Mounting Ordering

Code

Maximum

Flow, fpm*

Maximum

SP, in. WG**

Actuator, Tested as

Matched Set with

Damper (350°F)

Minimum: 15 x 14

Wall or Floor DMPR-S60024,

Maximum: 32 x 48

Wall TOVLE, 2500 4 DMPR-S60024S,

Maximum: 32 x 36

Floor TOVHE DMPR-S60120,

DMPR-S60120S

* Maximum Flow is the velocity against which the actuator listed in Table 8 will be able to operate the damper to the fully

closed position and provide the rated leakage in the marked direction of airflow.

** Maximum SP is the static pressure against which the actuator listed in Table 8 will be able to operate the damper from

the fully closed position in the marked direction of airflow.

Table 9: FS-1300 Dynamic Rating - Pneumatic Actuator

Width x Height, in. Mounting Ordering Code Maximum

Flow, fpm*

Maximum

SP, in. WG**

Actuator, Tested as

Matched Set with

Damper (350°F)

Minimum: 15 x 14

Wall or Floor TOVLP,

Maximum: 32 x 48

Wall TOVHP 2800 8 DS-3153-2

Maximum: 32 x 36

Floor

* Maximum Flow is the velocity against which the actuator listed in Table 9 will be able to operate the damper to the fully

closed position and provide the rated leakage in the marked direction of airflow.

** Maximum SP is the static pressure against which the actuator listed in Table 9 will be able to operate the damper from

the fully closed position in the marked direction of airflow.

Table 10: FS-1300 Dynamic Rating - Fire Mode

Width x Height, in. Mounting Ordering Code Maximum

Flow, fpm*

Maximum

SP, in. WG**

Actuator

Minimum: 15 x 14

Wall or Floor TOVLE, TOVHE,

Maximum: 32 x 48

Wall TOVLP, TOVHP 3500 8 Jackshaft Spring

Maximum: 32 x 36

Floor

Note: Table 10 information is based on a 20 psi minimum supply pressure for pneumatic actuators.

When multiple assemblies incorporate individual

sections operated by their own closure mechanism or

actuator, each individual section is to be operated at

the maximum specified airflow for the multiple

assembly with all other sections closed.

Table 11: UL Leakage-rated

Classifications

Class Static Pressure (SP), inches Water

14812

10 20 28 35

Note: The ratings in Table 11 are valid in either direction of

airflow.

Leakage in cfm/sq ft

FS-1300 Combination Fire/Smoke Dampers Product Bulletin

erformance Data

Temperature Rating

165°F (74°C) primary sensor with 250°F fusible link, or

212°F (100°C) primary sensor with 350°F fusible link

Electric Actuator

Control Circuit: 2-wire plus a ground wire

Input Voltage: 120 VAC @ 60 Hz (24 VAC @ 60 Hz optional)

Operating Time: Open, 20 seconds; Closed, 15 seconds

Auxiliary Switch: Single-Pole, Double-Throw (SPDT) makes or breaks circuit at powered

end of stroke.

Connections: Coded screw terminals

Rotation: Approximately 180 degrees

Power Requirements: 70 VA running, 25 VA holding

Pneumatic Actuator

Stroke: 3 in. (7.6 cm)

Supply Air Pressure: 20 psig (138 kPa) minimum compression fitting for copper tubing

Replacement Parts

DMPR-RS005: DMPR-S60024 - 60 lb·in, 24 VAC

DMPR-RS006: DMPR-S60024S- 60 lb·in, 24 VAC with Auxiliary Switch

DMPR-RS007: DMPR-S60120 - 60 lb·in, 120 VAC

DMPR-RS008: DMPR-S60120S - 60 lb·in, 120 VAC with Auxiliary Switch

DMPR-RS301: 250°F fusible link

DMPR-RS302: 350°F fusible link

DMPR-RS303: 165°F primary sensor

DMPR-RS304: 212°F primary sensor

All technical information is compiled from test data, corrected to standard temperature and pressure conditions,

determined using instrumentation and procedures in accordance with AMCA Standard for Test Methods for

Louvers, Dampers, and Shutters No. 500-89.

For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable

for damages resulting from misapplication or misuse of its products.

eturn Policy

All Johnson Controls Dampers are built to order, just in time and cannot be returned due to customer ordering

errors. All dampers are backed by a 3-year warranty, which covers defects in materials or workmanship. Refer to

terms and conditions of sale for specifics.

At Johnson Controls, delivering environmentally sound products and services is part of our corporate-wide

commitment to continuous improvement. We do this by reducing raw material consumption, recycling, eliminating

the use of toxins, and conserving and preserving natural resources. We believe that what is good for the

environment and the safety and health of all people is good for Johnson Controls. And we never forget that clean

water, air, and land is everyone’s business.

Controls Group www.johnsoncontrols.com

507 E. Michigan Street

FAN 268.1

P.O. Box 423 Damper and Actuator Product Guide

Milwaukee, WI 53201 Printed in U.S.A.

Johnson Controls FS-1300 User manual

Brand: Johnson Controls

Model: FS-1300

Category: Power extensions

Type: User manual

UL File No.

Download PDF

report

Johnson Controls FS-1300 User manual

Johnson Controls FS-1300 User manual

Related papers

Other documents