AnyMount KT04S User manual

Brand: AnyMount

Model: KT04S

Type: User manual

INSTALLATION INSTRUCTIONS

UNIVERSAL AIR CONDITIONER

MOUNTING BRACKET

KT-04L (MEDIUM/LARGE)

Supports up to 165 lbs.

KT-04S (SMALL/MEDIUM)

Supports up to 88 lbs.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

ANYMOUNT

Page 2

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

1. Read the enclosed instructions to ensure the safe and proper

method of installing the ANYMOUNT AC bracket.

2. Install the ANYMOUNT AC bracket from inside and never fully lean

out the window.

3. Not for use on dormers.

4. It is recommended that there be at least 10” of clearance below the

window.

5. There may be times when objects such as awnings, signage, lighting

and masonry structures below a window may obstruct and prevent

the proper installation of the ANYMOUNT AC bracket.

6. The ANYMOUNT AC bracket does not reduce, eliminate or mitigate

the requirements of any air conditioner manufacturer in the

mounting and installation of their specic product.

7. Be sure that the window sill/stool to which you are mounting the

AC bracket is in good condition and capable of helping support the

weight of the AC unit.

SAVE THESE INSTRUCTIONS

HOUSEHOLD USE ONLY

WARNING

WARNING - Hazards or unsafe

practices which COULD result in

severe personal injury or death

DANGER

DANGER - Immediate hazards

which WILL result in severe

personal injury or death

CAUTION

CAUTION - Hazards or unsafe

practices which COULD result in

minor personal injury

WARNING

Do not overload the ANYMOUNT AC bracket in excess of its

maximum capacity of 88 pounds for model KT-04S and

165 pounds for model KT-04L

Page 3

PARTS

ID Illustration Description Quantity

A Support Bar 1

B Adjustable Arm 1

C Base (Main) Unit 1

D Rubber Spacer 1

E Metal Washer 2

F Plastic Washer 2

G Nylon Spacer 2

H Nylon Block 1

M6 Type 85mm

Screws

M5 Type 10mm

Screws

K M5 Hex Nut 2

Screw Hole

Covers

4mm Hex/Allen

Wrench

3mm Hex/Allen

Wrench

NOTES: NOT INCLUDED BUT NEEDED FOR ASSEMBLY: 8mm and 10mm socket

wrenches or adjustable wrench/pliers and electric drill.

Page 4

SET UP & USE

STEP 1

Attach adjustable arm to base (main unit) using the provided Type M6 85mm

screws, metal washers and hex nuts.

NOTES: The screws, metal washers and hex nuts are already connected to the

adjustable arm. Step 1 assembly will require the included 4mm hex key and a

10mm socket wrench or adjustable wrench (not included).

Page 5

SET UP & USE

STEP 2

Attach support bar to the main unit using M5 10mm screws and M5 hex nuts. This

assembly will require the included 3mm hex key and an 8mm socket wrench of

adjustable wrench (not included).

Page 6

SET UP & USE

STEP 3

With a at horizontal window sill:

Use the rubber spacer, plastic washer and/or nylon spacer to make the base (main)

unit of the AC window bracket horizontal with the window.

With an inclined window sill:

Use the rubber spacer, plastic washer and/or nylon block to make the base (main

unit) of the AC window bracket horizontal with the window.

Page 7

SET UP & USE

STEP 4

Place the nylon spacer (for horizontal window sills) or the nylon block (for inclined

window sills) in the middle of the window stool and use a pencil to mark all three

holes of the spacer or block. Use a drill with a 3/16” bit to drill all three holes into the

window sill to a depth of 85mm (3.3 Inches).

Page 8

SET UP & USE

STEP 5

Sink the M6 type 85mm screw into the center hole that you have drilled until it is

ush with the sill.

Page 9

SET UP & USE

STEP 6

Align the spacers and/or washers you are utilizing with the holes in the bottom of

the base (main unit). Sink M6 type 85mm screws into the right and left holes of the

spacer and/or washers until base (main unit) is secure to the window sill.

Align adjustable arm until wedge-shaped foot is ush to the wall.

NOTE for model KT-04L: Mounts to any surface up to 15.2” from wall.

Adjustable arm height 7.1” - 11.6”.

NOTE for model KT-04S: Mounts to any surface up to 10.4” from wall.

Adjustable arm height 4.5” - 6.6”.

Page 10

SET UP & USE

STEP 7

By hand or with small wrench, adjust the nut on the adjustable arm until the bubble

level built into the base (main) unit shows that the base (main) unit is on a slight

downward angle.

NOTE: If you remove the window AC bracket for any reason, insert the provided

screw hole covers into the holes that you created in your window sill to help

prevent moisture from entering.

Page 11

WARRANTY

LIMITED WARRANTY

The ANYMOUNT brand is under license. Any

repair, replacement, or warranty service, and

all questions about this product should be

directed to ANYCOM Products USA LLC at

1-855-855-0294 from the USA or Puerto Rico.

ANYCOM Products USA LLC warrants to

the original purchaser that the product will

be free from defects in material, parts and

workmanship for the period designated for

this product. The warranty commences the

day the product is purchased (please keep

original proof of purchase) and covers up to a

period of 1 year (12 months) for labor/1 year

(12 months) for parts (manufacturing defects

only).

ANYCOM Products LLC agrees that it will, at

its option, replace the defective product with

either a new or remanufactured AC bracket

equivalent to your original purchase during the

warranty period.

ANYCOM Products is not liable for any loss,

cost, expense, inconvenience or damage

that may result from improper installation,

misuse, abuse, alteration, accident, normal

wear and tear, and use, or inability to use, the

ANYMOUNT AC bracket.

Claims not to exceed the purchase price of the

ANYMOUNT AC bracket. No other warranty is

expressed or implied. For warranty service or

replacement part information, please contact

ANYCOM Products USA LLC

1356 Broadway

NY, NY 10018

1-855-855-0294

Page 12

ANYMOUNT

September 2016 Printed in China

AnyMount KT04S User manual

Brand: AnyMount

Model: KT04S

Type: User manual

Download PDF

report

AnyMount KT04S User manual

AnyMount KT04S User manual

Other documents