HD WiFi Camera NVR Kit
Quick Start Guide
1
1
HDD Installation
Make sure that your NVR is powered off and unplugged
from the power source. Loosen the screws from the
cover panel on the bottom of the NVR and remove the
panel.
Slide the cover off and connect the SATA power and
data cables from the NVR to the corresponding ports
on your HDD.
Once connected, place the HDD and cables into the
NVR. Cover the HDD with the rubber buffer so that the
NVR is secure.
Slide the cover panel and fasten it onto the NVR using
the screws from step 1.
If your system does not include a pre-installed HDD, you
can purchase your own and follow the steps below for
installation. Make sure you purchase a 2.5” HDD
optimized for always-on read/write surveillance, e.g.
low-power WD AV-25 hard drives.
Camera
Power Supply
Display
NVR
Wireless Router
Note: Image may vary for your specific NVR model.
This quick start guide will help you configure your NVR kit
for initial use. Follow the steps below to connect your NVR
system.
2
Connecting your system
Connect the NVR to the included power adapter and plug
it into a nearby power outlet.
1
Connect the NVR to an empty network port on the WiFi
router that you will connect your cameras to. You may use
the provided ethernet cable.
2
(Optional) You can connect an external monitor to view
your NVR locally. Use the HDMI port (cable not included)
to connect the NVR to your local display. Follow the
diagram to finish connecting your system.
3
Note: There will be no password when you first use your NVR. However, we
strongly recommend that you set a password after you configure your NVR.
Set a password by going to the Main Menu > General Settings > Account
Settings.
2
Safety Requirements
Place your NVR in a well-ventilated area.
Do not place any objects on top of your NVR.
Try to keep your NVR in a cool operating temperature.
Do NOT move or shake the NVR while operating, or
else the hard drive will be damaged.
Use a surge protector to protect the NVR from shortages.
3
Use only the provided power adapters with your products.
If water or any liquid comes into contact with the NVR,
unplug it immediately and contact Zmodo support.
Your NVR may have encountered an error. Try restarting the
NVR. If the problem still persists, please contact Zmodo
Support.
The hard drive is not working properly or no hard drive was
detected.
The NVR is reading the hard drive.
The NVR is powered on. No light means the NVR is off.
Three LED Indicators will tell you the status of your NVR.
Please refer to the chart for specific details.
Blinking blue
Solid green
Solid red
Blinking red
NVR Status Light Indicator
Zmodo
Before you perform any permanent installation, make sure
you complete the mobile setup to configure your cameras
and NVR kit.
® TM
You will need to use an iOS or Android
mobile device for setup.
3
Mobile Setup
Before you begin:
Plug in and power on all cameras near your router for
initial setup. Fasten the antennas (if applicable) onto the
cameras. You can relocate the cameras after you
complete the Mobile Setup.
4
Make sure that you have a strong WiFi connection at the
location of your cameras. Visit www.zmodo.com/support
for advice on improving your WiFi signal range.
Make sure you know the SSID (WiFi network name) and
password of the 2.4GHz WPA-PSK/WPA2-PSK WiFi
network that you want your camera to connect to. Your
network cannot be hidden.
Network Requirements:
720p cameras: Requires at least 1mbps upload when live
viewing or 2mbps upload when using the Cloud Service
for each camera.
1080p cameras: Requires at least 2mbps upload when
live viewing or 4mbps upload when using the Cloud
Service for each camera.
TM
Download and install the “Zmodo” app from Google Play
TM TM
or the App Store (compatibility: iOS 9.0+ or Android
4.0+). Launch the app and sign up for a free Zmodo
account. All of your devices will be bound to this account.
®
5
Select the “Zink” connection method
to connect your WiFi NVR Kit. Your
WiFi NVR Kit will be added to your
Zmodo account.
2
This device can be set up with a Zmodo Beam. If you own a
Beam, please follow the instructions in your Beam quick guide
to connect your device instead.
Connect with
Beam
1
Log in and press in the upper
right corner. Select "Add Device".
+
6
5
Select the network named “ZMD_SAP”
and connect to it.
Note: If you see a "No Internet Connection" error
message, please ignore it and connect anyway.
Follow the on-screen instructions and
select “Tap here to begin setup” to go
to the WiFi settings page on your
smartphone.
4
3
5
Note: If you are using an iOS device, you will need
to manually go to the WiFi settings page on your
smartphone.
Select the number of devices that
you will be connecting. The number
of devices will be the number of
WiFi cameras ("N") plus the NVR, or
N+1. For example, if you are
configuring a 4 camera kit, the
number of devices will be 5.
Tap to proceed.
√
7
7
If you see this screen, the app will
connect your WiFi NVR Kit to your
WiFi network. This may take a few
minutes. Once it’s completed, please
skip to step 11.
If you do not see this screen, please
proceed to step 8.
Note: If you are connecting multiple devices, you
will need to wait for the app to find and connect all
devices.
8
If this app interface appears, please
press “Tap here to select WiFi”.
ZMD_SAP
Return to the Zmodo app page and
select or enter the SSID and password
of the WiFi network that you want your
cameras to connect to.
Note: The WiFi name and password are case-
sensitive.
Tap to proceed.
√
6
Note: If you are using an iOS device, you will need
to manually go to the WiFi settings page on your
smartphone.
8
10
The app will automatically search for
your WiFi NVR Kit and connect it to
the WiFi network. This may take a
few minutes.
Note: If you are connecting multiple devices, you
will need to wait for the app to find and connect
all devices.
9
Select the WiFi network that your WiFi
NVR Kit will connect to, and connect
to it. Return to the Zmodo app once
your mobile device is connected to
the WiFi network.
Name your NVR and set a password
for each device. Tap to proceed.
Note: The password provides an additional layer
of security for your devices. You will not need to
use this password when accessing your devices
from the Zmodo app. It is not required, but it is
highly recommended.
√
11
9
Mounting your cameras
4
Installation Requirements & Tips:
If you’re installing your cameras outdoors, all wired
connections must be weatherproofed.
Make sure that your cameras are within range of your
WiFi network, and that your network meets all of the
bandwidth requirements from Section 3.
Try to avoid WiFi signal interference from concrete,
cement, and metal as much as possible. Do not place
cameras in a location where these materials stand
between your cameras and your WiFi router.
12
Your cameras have been
successfully configured! Your
cameras will be automatically
grouped together in the Device List.
Once you have configured all
cameras, you can unplug your
cameras and begin mounting.
Before installing the cameras, carefully plan where and
how they will be positioned, and how you will route the
wiring that connects your cameras to the power
adapters.
10
Unplug and power off the cameras that have been
configured in Section 3.
1
Line the camera bracket against the wall where you
would like to install the cameras, and mark the
appropriate holes. Drill three holes slightly smaller than
the wall anchors and use a hammer to gently insert the
anchors into the wall. Fasten the three screws through
the holes on the bracket and into the anchors as shown.
Note: Depending on the camera model that you purchased, the camera
bracket may or may not be fastened onto the camera when first removed
from factory packaging.
2
(image may vary for your specific camera model)
If you have a lot of obstacles between your camera and
the WiFi router, the transmission range will be greatly
reduced. In order to increase the range, you may
purchase a WiFi range extender to place near the
cameras. Please visit for other www.zmodo.com/support
tips on improving your WiFi signal range.
Connect the supplied power adapter to the power port
on the camera, and plug the adapter into a nearby
power outlet. Repeat steps 1-4 for all cameras in your
camera kit.
4
(image may vary for your specific camera model)
Fasten the bracket to the camera. You will be able to
adjust the camera position using the adjustable camera
bracket. Position the camera for an optimal viewing
angle, and tighten the bracket.
3
(image may vary for your specific camera model)
11
12
5
Recording and Viewing Options
Recording Options
Record continuously and store footage on our secure
cloud servers.
Create and save video clips from your recordings.
Access your footage and clips at any time from any
location.
Enjoy more smart features in the future!
This kit is compatible with the Zmodo Cloud Service.
Please visit for information about www.zmodo.com/cloud
the Zmodo Cloud Service. The cloud service will allow you
to:
All of your Zmodo devices will be bound to your Zmodo
user account. You can access your camera and other
TM
devices by using the Zmodo app with any Android or
®
iOS device. Just download the Zmodo app from
TM TM
Google Play or the App Store .
You can also access your devices from any web browser
with our web app. Visit and log in with user.zmodo.com
your Zmodo user account information.
Viewing Options
13
Status Ring Definitions
6
If you were unable to connect your successfully:camera
Please make sure that you entered the network name
and password correctly. Note: Both are case-sensitive.
Make sure that you are connecting to a 2.4GHz WPA-
PSK/WPA2-PSK WiFi network, and your network is not
hidden.
Your camera may have an LED light that indicates the
status of your camera. If it does, please refer to the
guide below:
You may need to improve your WiFi strength. Visit
www.zmodo.com/support for suggestions.
Make sure that you have fastened the antenna (if applicable)
onto your camera, and try moving your camera closer to the
router for the initial setup.
Blinking blue
The camera is connecting to the WiFi network. Please do
NOT turn off or unplug your camera at this time.
Blinking green
The camera is ready for setup.
The camera is powering on.
Solid green
The camera has successfully connected to the WiFi network.
Solid blue
14
REV-A1 0
Support
7
Having difficulty?
You can use the Live Chat function in Zmodo app if you
have any technical problems.
Please follow the steps below:
Go to "Me" in the bottom right corner in Zmodo app and
select "Zmodo Support".
For more instructions, troubleshooting, support, and
other resources, please visit:
www.zmodo.com/support
Follow us on Twitter @Zmodo
Scan the QR-code below!
Like us on Facebook.com/Zmodo
Scan the QR-code below!
Android is a trademark of Google Inc. Google Play is a trademark of
Google Inc. Apple, the Apple Logo, and iPhone are trademarks of Apple
Inc., registered in the U.S. and other countries. App Store is a service mark
of Apple Inc.
/
