Linksys WRT54G3G-ST User manual

A Division of Cisco Systems, Inc.

®

Model No.

Internet Video Camera

Wireless-G

WVC54G

User Guide

WIRELESS

GHz

2.4

802.11g

Wireless-G Internet Video Camera

Copyright and Trademarks

Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco

rights reserved. Other brands and product names are trademarks or registered trademarks of their respective

holders.

How to Use this Guide

Your guide to the Wireless-G Internet Video Camera has been designed to make understanding networking with

the Camera easier than ever. Look for the following items when reading this guide:

In addition to these symbols, there are definitions for technical terms that are presented like this:

Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like

this:

Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.

This exclamation point means there is a Caution or

warning and is something that could damage your

property or the Camera.

word: definition.

This checkmark means there is a Note of interest and

is something you should pay special attention to while

using the Camera.

This question mark provides you with a reminder about

something you might need to do while using the Camera.

Figure 0-1: Sample Figure Description

WVC54G-UG-40420NC JL

Wireless-G Internet Video Camera

Table of Contents

Chapter 1: Introduction 1

Welcome 1

What’s in this Guide? 2

Chapter 2: Planning Your Wireless Network 4

Introduction 4

Ad-Hoc and Infrastructure Modes 4

Network Layout 4

Chapter 3: Getting to Know the Wireless-G Internet Video Camera 6

Camera LCD Screen and Built-in Microphone 6

Camera LEDs 6

Camera Head 6

Camera Ports 7

Chapter 4: Connecting the Wireless-G Internet Video Camera for Setup 8

Overview 8

Connection to a Wired Network for Setup 8

Connection to a Wireless Ad-Hoc Network for Setup 8

Moving the Camera to a Different Network 9

Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera 10

Setup Wizard 10

Placement Options 16

Audio Option 16

Chapter 6: Installing and Using the Wireless-G Internet Video Camera Viewer

& Recorder Utility 17

Overview 17

Installing the Viewer & Recorder Utility 17

Using the Viewer & Recorder Utility 19

Chapter 7: Setting up the Linksys SoloLink™ DDNS Service 30

Overview 30

Introduction 30

Setup Wizard for the SoloLink DDNS Service 30

SoloLink Registration of Additional Cameras 40

Wireless-G Internet Video Camera

Chapter 8: Using the Wireless-G Internet Video Camera’s Web-based Utility 42

Overview 42

How to Access the Web-based Utility 42

View Video 42

Setup 43

Help 54

Appendix A: Troubleshooting 56

Common Problems and Solutions 56

Frequently Asked Questions 59

Appendix B: Wireless Security 62

Security Precautions 62

Security Threats Facing Wireless Networks 62

Appendix C: Upgrading Firmware 64

Appendix D: Windows Help 65

Appendix E: Glossary 66

Appendix F: Specifications 73

Appendix G: Warranty Information 75

Appendix H: Regulatory Information 76

Appendix I: Contact Information 79

Wireless-G Internet Video Camera

List of Figures

Figure 3-1: Camera LCD Screen and Built-in Microphone 6

Figure 3-2: Camera LEDs 6

Figure 3-3: Camera Head 6

Figure 3-4: Camera Ports 7

Figure 4-1: Connect the Ethernet Network Cable 8

Figure 4-2: Connect the Power Adapter 8

Figure 5-1: Setup Wizard - Welcome Screen 10

Figure 5-2: Connection for Setup Screen 10

Figure 5-3: Cameras Found Screen 11

Figure 5-4: Login Screen 11

Figure 5-5: Basic Settings Screen 11

Figure 5-6: Network Settings Screen 12

Figure 5-7: IP Settings Screen 12

Figure 5-8: Mode Settings Screen 13

Figure 5-9: Wireless Settings Screen 13

Figure 5-10: Security Settings Screen 14

Figure 5-11: Review New Settings Screen 14

Figure 5-12: Confirmation Screen 15

Figure 5-13: Congratulations Screen 15

Figure 5-14: Stand Option 16

Figure 5-15: Camera Desktop Stand 16

Figure 5-16: Wall Mount Option 16

Figure 5-17: Wall-Mount Slots 16

Figure 6-1: Install Viewer & Recorder Utility Screen 17

Figure 6-2: Install Viewer & Recorder Utility - Welcome Screen 17

Figure 6-3: Choose Destination Location Screen 18

Figure 6-4: Select Program Folder Screen 18

Figure 6-5: OCX Plug-in Screen 18

Wireless-G Internet Video Camera

Figure 6-6: Setup Complete Screen 18

Figure 6-7: Viewer & Recorder Utility Icon 19

Figure 6-8: Main Screen 19

Figure 6-9: Find Camera from LAN Screen 20

Figure 6-10: Camera Added Successfully Screen 20

Figure 6-11: Find Camera from Internet Screen 21

Figure 6-12: Change Settings Screen 21

Figure 6-13: Delete Camera Screen 22

Figure 6-14: Confirm Deletion of Camera Screen 22

Figure 6-15: View Video Screen 23

Figure 6-16: Recording Icon Screen 23

Figure 6-17: Scheduled Recordings in Progress Screen 26

Figure 6-18: Files Screen 26

Figure 6-19: Recorded Files Screen 26

Figure 6-20: Window Showing SnapShot Folders 27

Figure 6-21: Preferences Screen 27

Figure 6-22: Recording Schedule Screen 28

Figure 6-23: Add to Recording Schedule Screen 28

Figure 6-24: Stop Scheduled Recording Screen 29

Figure 6-25: View Video Screen 29

Figure 7-1: SoloLink Service 30

Figure 7-2: SoloLink Welcome Screen 30

Figure 7-3: SoloLink for Dynamic IP Address Screen 31

Figure 7-4: SoloLink for Convenience Screen 31

Figure 7-5: Check Connections Screen 32

Figure 7-6: Cameras Found Screen 32

Figure 7-7: Login Screen 33

Figure 7-8: SoloLink DDNS Screen 33

Figure 7-9: Confirm Active Internet Connection Screen 34

Figure 7-10: Welcome to the SoloLink DDNS Service Screen 34

Wireless-G Internet Video Camera

Figure 7-11: Sign Up Screen 35

Figure 7-12: Confirmation of New Settings Screen 36

Figure 7-13: Select a Location ID Screen 36

Figure 7-14: Confirm Your Location ID Screen 37

Figure 7-15: Payment Screen 37

Figure 7-16: Verification Screen 37

Figure 7-17: Create Links Screen 38

Figure 7-18: Successful Registration Screen 38

Figure 7-19: Account Confirmation of Camera Screen 39

Figure 7-20: Successful Setup Screen 39

Figure 7-21: Port Forwarding Information 40

Figure 7-22: Web-based Utility Welcome 40

Figure 7-23: Web Utility Login Screen 40

Figure 7-24: SoloLink DDNS Screen 41

Figure 7-25: Find Available Port Screen 41

Figure 8-1: Camera’s Default IP Address 42

Figure 8-2: Web-based Utility Welcome 42

Figure 8-3: Security Warning Screen 43

Figure 8-4: Web Utility Login Screen 43

Figure 8-5: Basic Screen 44

Figure 8-6: Confirmation Screen 45

Figure 8-7: WEP Key Settings Screen 45

Figure 8-8: Image Screen 46

Figure 8-9: Password Screen 47

Figure 8-10: Users Screen 48

Figure 8-11: Add/Modify User Screen 48

Figure 8-12: SoloLink DDNS Screen 49

Figure 8-13: New User Registration Screen 49

Figure 8-14: Password Request Screen 50

Figure 8-15: Manage Your SoloLink DDNS Account 50

Wireless-G Internet Video Camera

Figure 8-16: Device Removal Screen 50

Figure 8-17: Find Available Port Screen 51

Figure 8-18: Status Screen 52

Figure 8-19: Options Screen 53

Figure 8-20: Administrator Help 54

Figure 8-21: Upgrade Firmware Screen 55

Figure C-1: Upgrade Firmware Screen 64

1

Chapter 1: Introduction

Welcome

Wireless-G Internet Video Camera

Chapter 1: Introduction

Welcome

Thank you for choosing the Linksys Wireless-G Internet Video Camera. This Camera sends live video through the

Internet to a web browser anywhere in the world! This compact, self-contained unit lets you keep an eye on your

home, your kids, your workplace—whatever’s important to you.

How does the Camera do all of this? Unlike standard “web cams” that require an attached PC, the Internet Video

Camera contains its own web server, so it can connect directly to a network, either over Wireless-G (802.11g)

networking, or over 10/100 Ethernet cable. The advanced MPEG-4 video compression produces a high-quality,

high-framerate, up to 640 x 480 audio/video stream.

The Internet Video Camera’s unique form-factor and wireless connectivity allows you to mount it on a wall nearly

anywhere, or slip it into its included stand for desktop use. Once it’s connected to your home network, you can

“see what it sees” from any PC in the house, while the audio/video stream is secured from the outside world,

hidden behind your Router. If you want the video to be visible from outside your home network, you can open an

appropriate port on the Router, and then create password-protected accounts to manage access to the Camera,

or leave it wide open for the world to see. The SoloLink DDNS Service (trial sign-up included) lets you access your

Camera using an easy-to-remember “name”, even if your home Internet connection uses a dynamic IP address.

You can also turn on Security Mode, which tells the Camera to send you an e-mail message with a short video

attached to up to three e-mail addresses whenever it detects motion in its field of view. You can then log onto the

live video stream if the situation warrants. The included Viewer & Recorder utility lets you record the audio/video

stream to your local hard drive, “live” or on a predetermined schedule.

Use the instructions in this Guide to help you integrate the Camera into your network. These instructions should

be all you need to get the most out of the Wireless-G Internet Video Camera.

Ethernet: an IEEE standard network

protocol that specifies how data is

placed on and retrieved from a

common transmission medium.

802.11g: An IEEE wireless networking

standard that specifies a maximum

data transfer rate of 54Mbps, an

operating frequency of 2.4GHz, and

backward compatibility with 802.11b

devices.

2

Chapter 1: Introduction

What’s in this Guide?

Wireless-G Internet Video Camera

What’s in this Guide?

This user guide covers the steps for setting up and using the Wireless-G Internet Video Camera.

• Chapter 1: Introduction

This chapter describes the Camera’s applications and this User Guide.

• Chapter 2: Planning Your Wireless Network

This chapter discusses a few of the basics about wireless networking.

• Chapter 3: Getting to Know the Wireless-G Internet Video Camera

This chapter describes the physical features of the Camera.

• Chapter 4: Connecting the Wireless-G Internet Video Camera

This chapter instructs you on how to connect the Camera to your network before you run the Setup Wizard.

• Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera

This chapter instructs you on how to use the Setup Wizard for setup and configuration of the Camera, as well

as how to mount the Camera.

• Chapter 6: Installing and Using the Wireless-G Internet Video Camera Utility

This chapter explains how to install and use the Wireless-G Internet Video Camera Utility on your PC, so you

can view and record video.

• Chapter 7: Setting up the Linksys SoloLink™ DDNS Service

This chapter discusses the advantages of the SoloLink DDNS Service and walks you through the setup

procedure.

• Chapter 8: Using the Wireless-G Internet Video Camera Web-based Utility

This chapter describes the Web-based Utility and the features available, so you can use and alter advanced

configuration settings.

• Appendix A: Troubleshooting

This appendix describes some problems and solutions, as well as frequently asked questions, regarding

installation and use of the Camera.

• Appendix B: Wireless Security

This appendix discusses security issues regarding wireless networking and measures you can take to help

protect your wireless network.

3

Chapter 1: Introduction

What’s in this Guide?

Wireless-G Internet Video Camera

• Appendix C: Upgrading Firmware

This appendix explains how you can upgrade the Camera’s firmware.

• Appendix D: Windows Help

This appendix describes how you can use Windows Help for instructions about networking, such as installing

the TCP/IP protocol.

• Appendix E: Glossary

This appendix gives a brief glossary of terms frequently used in networking.

• Appendix F: Specifications

This appendix provides the technical specifications for the Camera.

• Appendix G: Warranty Information

This appendix supplies the warranty information for the Camera.

• Appendix H: Regulatory Information

This appendix supplies the regulatory information regarding the Camera.

• Appendix I: Contact Information

This appendix provides contact information for a variety of Linksys resources, including Technical Support.

4

Chapter 2: Planning Your Wireless Network

Introduction

Wireless-G Internet Video Camera

Chapter 2: Planning Your Wireless Network

Introduction

A wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each

computer in the WLAN uses a wireless device to connect to the network. Computers and other devices, such as

peripherals, in a WLAN share the same frequency channel and SSID, which is an identification name for wireless

devices.

Ad-Hoc and Infrastructure Modes

Unlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure

and ad-hoc. An infrastructure configuration is a WLAN and wired LAN communicating to each other through an

access point. An ad-hoc configuration is wireless-equipped computers communicating directly with each other.

Choosing between these two modes depends on whether or not the wireless network needs to share data or

peripherals with a wired network or not.

If the computers on the wireless network need to be accessed by a wired network or need to share a peripheral,

such as a printer, with the wired network computers, the wireless network should be set up in infrastructure

mode. The basis of infrastructure mode centers around an access point, which serves as the main point of

communications in a wireless network. (A wireless router can also be used because a wireless router

incorporates the capabilities of an access point.) Access points transmit data to PCs equipped with wireless

network cards, which can roam within a certain radial range of the access point. Multiple access points can be

arranged to work in succession to extend the roaming range, and can be set up to communicate with your

Ethernet (wired) hardware as well.

If the wireless network is relatively small and needs to share resources only with the other computers on the

wireless network, then the ad-hoc mode can be used. Ad-hoc mode allows computers equipped with wireless

transmitters and receivers to communicate directly with each other, eliminating the need for an access point.

The drawback of this mode is that, in Ad-Hoc mode, wireless-equipped computers are not able to communicate

with computers on a wired network. And, of course, communication between the wireless-equipped computers

is limited by the distance and interference directly between them.

Network Layout

The Wireless-G Internet Video Camera is compatible with all 802.11b and 802.11g routers, such as model

numbers BEFW11S4 and WRT54G, as well as access points, including model numbers WAP11 and WAP54G. The

Infrastructure: configuration in which

a wireless network is bridged to a

wired network via an access point.

LAN (Local Area Network): the

computers and networking products

that make up the network in your home

or office.

Ad-hoc: a group of wireless devices

communicating directly to each other

(peer-to-peer) without the use of an

access point.

WLAN (Wireless Local Area

Network): A group of computers and

associated devices that communicate

with each other wirelessly.

5

Chapter 2: Planning Your Wireless Network

Network Layout

Wireless-G Internet Video Camera

Camera will also communicate with network adapters, such as the Wireless-B and Wireless-G Notebook Adapters

(model numbers WPC11 and WPC54G) for your laptop computers, Wireless-B and Wireless-G PCI Adapters (model

numbers WMP11 and WMP54G) for your desktop PCs, and Wireless-B and Wireless-G USB Adapters (model

numbers WUSB11 and WUSB54G) for your computers when you want to enjoy USB connectivity.

With these, and many other Linksys products, your networking options are limitless. Go to the Linksys website at

www.linksys.com for more information about products that work with the Wireless-G Internet Video Camera.

6

Chapter 3: Getting to Know the Wireless-G Internet Video Camera

Camera LCD Screen and Built-in Microphone

Wireless-G Internet Video Camera

Chapter 3: Getting to Know the Wireless-G Internet Video

Camera

Camera LCD Screen and Built-in Microphone

The Camera has a LCD screen that indicates the Camera’s current IP address and whether it is a fixed or dynamic

address. If the Camera uses a fixed IP address, then the screen will display the word “FIXED.” If the Camera uses

a dynamic IP address, then the screen will display the word “DHCP.”

The built-in microphone is located approximately one inch below the LCD screen, in the middle of the Camera’s

front panel. It has a range of approximately 9 feet (3 meters), depending on environmental conditions.

Camera LEDs

The Camera has four LEDs to let you know how the Camera is functioning.

READY Green. The READY LED lights up when the Camera is powered on. It flashes while the

Camera is initializing and is steadily lit when the Camera is ready for use.

ACT/LINK Green. The ACT/LINK LED flashes when there is activity.

ETHERNET Green. The ETHERNET LED lights up when there is a connection to a wired network. It flashes

when data is transmitted to or received from the wired network.

WIRELESS Green. The WIRELESS LED lights up when there is a connection to a wireless network. It

flashes when data is transmitted to or received from the wireless network.

Camera Head

The Camera head and its focus ring allow you to modify the aim and focus of the Camera.

To alter the Camera’s aim, swivel the Camera head.

To adjust the Camera’s focus, rotate the dark gray focus ring.

Figure 3-1: Camera LCD Screen and Built-in Microphone

Figure 3-2: Camera LEDs

Figure 3-3: Camera Head

Built-in

Microphone

7

Chapter 3: Getting to Know the Wireless-G Internet Video Camera

Camera Ports

Wireless-G Internet Video Camera

Camera Ports

The Camera features three ports and a Reset button on the bottom panel.

POWER The POWER port is where you will connect the power adapter.

MIC IN The MIC IN port is where you will connect the 2.5 mm input jack of your external microphone

(optional).

ETHERNET The ETHERNET port is where you will connect the Ethernet network cable.

RESET The RESET button is what you will press if you need to reset the Camera. Insert a paper clip

into the opening next to the Ethernet port. Then press the button and hold it in for five seconds.

IMPORTANT: Resetting the Camera will erase

all of your settings, such as encryption

information, and replace them with the factory

defaults. Do not reset the Camera if you want

to retain these settings.

Figure 3-4: Camera Ports

8

Chapter 4: Connecting the Wireless-G Internet Video Camera for Setup

Overview

Wireless-G Internet Video Camera

Chapter 4: Connecting the Wireless-G Internet Video Camera

for Setup

Overview

Before you set up the Camera, connect it to a wired or wireless network. Proceed to the appropriate section for

your setup.

If you need to move the Camera from a wired network to a wireless network, or vice versa, go to this section,

“Moving the Camera to a Different Network.”

Connection to a Wired Network for Setup

1. Attach the antenna.

2. Connect the Ethernet network cable to your router, switch, or computer.

3. Connect the other end of the cable to the Ethernet port on the Camera. See Figure 4-1.

4. Connect the power adapter to the Power port on the Camera.

5. Plug the power adapter into an electrical outlet.

The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready

and Ethernet LEDs are solidly lit.

Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”

Connection to a Wireless Ad-Hoc Network for Setup

1. Make sure your computer has the following wireless settings:

• SSID - linksys

• Network Mode - Ad-Hoc

• Channel - 6

• WEP - Disabled

2. Attach the antenna.

NOTE: You MUST connect the Camera to a PC,

router, or switch using the Ethernet network

cable BEFORE powering on the Camera.

Otherwise, the Camera will not function.

Figure 4-2: Connect the Power Adapter

Figure 4-1: Connect the Ethernet Network Cable

9

Chapter 4: Connecting the Wireless-G Internet Video Camera for Setup

Moving the Camera to a Different Network

Wireless-G Internet Video Camera

3. Connect the power adapter to the Power port on the Camera.

4. Plug the power adapter into an electrical outlet.

The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready

and Wireless LEDs are solidly lit.

Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”

Moving the Camera to a Different Network

When you move the Camera from a wired network to a wireless network, or vice versa, you must power off the

Camera before connecting to the new network. Proceed to the appropriate instructions.

To move the Camera from a wired network to a wireless network, follow these instructions:

1. Unplug the power adapter from the Camera.

2. Unplug the Ethernet network cable from the Camera.

3. Re-connect the power adapter to the Power port on the Camera.

The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready

and Wireless LEDs are solidly lit.

Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”

To move the Camera from a wireless network to a wired network, follow these instructions:

1. Unplug the power adapter from the Camera.

2. Connect the Ethernet network cable to your PC, router, or switch.

3. Connect the other end of the cable to the Ethernet port on the Camera.

4. Re-connect the power adapter to the Power port on the Camera.

The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready

and LAN LEDs are solidly lit.

Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”

10

Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera

Setup Wizard

Wireless-G Internet Video Camera

Chapter 5: Setting up and Mounting the Wireless-G Internet

Video Camera

Setup Wizard

The Wireless-G Internet Video Camera Setup Wizard will guide you through the installation and configuration

procedure.

1. Insert the Setup CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the

Welcome screen should appear. If it does not, click the Start button and choose Run. In the field provided,

enter D:\wvc54g.exe (if “D” is the letter of your CD-ROM drive).

• Setup. Click the Setup button to begin the installation process.

• Install Viewer & Recorder Utility. Click this button to install the Camera’s Viewer & Recorder Utility on

your PC.

• Setup SoloLink DDNS Service. Click the Setup SoloLink DDNS Service button to configure and use

Linksys’s Dynamic Domain Name System (DDNS) service.

• User Guide. Click this button to open the PDF file of this User Guide.

• Exit. Click the Exit button to exit the Setup Wizard.

2. To install the Camera, click the Setup button on the Welcome screen.

3. When you see the screen shown in Figure 5-2, make sure the Camera is properly connected to either a wired

or wireless network. Then click the Next button to continue.

Figure 5-2: Connection for Setup Screen

Figure 5-1: Setup Wizard - Welcome Screen

11

Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera

Setup Wizard

Wireless-G Internet Video Camera

4. The screen shown in Figure 5-3 displays a list of Wireless-G Internet Video Cameras on your network, along

with the status information for the Camera whose name is highlighted. In the Selection box, click the name of

the Camera you are currently installing. Write down the IP address of the Camera, so you can use it to access

the Web-based Utility later. Click the Next button.

5. For security purposes, you will be asked to enter a name and password in order to have administrator access

to the Camera. In lowercase letters, enter admin in the Administrator Name and Administrator Password

fields (later you can change these through the Web-based Utility). Then click the OK button.

6. On the Basic Settings screen, you can alter the following settings:

• Camera Name. You can give the Camera a unique name. Memorable names are helpful, especially if you

are using multiple Cameras on the same network. It should have 15 characters or fewer.

• Description. You may enter additional information, such as location, in this field. It has a maximum length

of 32 characters.

• Time Zone. Select the time zone for the Camera’s location.

• Date. Enter today’s date in the fields provided.

• Time. Enter the current time in the fields provided.

When you have finished making your changes, click the Next button.

Figure 5-4: Login Screen

Figure 5-3: Cameras Found Screen

Figure 5-5: Basic Settings Screen

12

Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera

Setup Wizard

Wireless-G Internet Video Camera

7. If your network has a DHCP server, such as a router with DHCP enabled, click the Automatic Configuration-

DHCP radio button. If you need to assign a static IP address to the Camera, keep the default setting, Static IP

address.

Then click the Next button.

8. If you selected Automatic Configuration-DHCP in step 7, then proceed to step 9.

If you selected Static IP Address, then the IP Settings screen will appear. Enter an IP Address, Subnet Mask,

and Default Gateway appropriate for your network. You must specify an IP Address and Subnet Mask on this

screen. If you are unsure about the Default Gateway, it is better to leave this field blank. Then complete the

Primary DNS and/or Secondary DNS fields. You must enter at least one DNS address, which can be obtained

from your ISP. Click the Next button.

Figure 5-6: Network Settings Screen

Figure 5-7: IP Settings Screen

Page is loading ...

Linksys WRT54G3G-ST User manual

This manual is also suitable for

Linksys WRT54G3G-ST User manual

Related papers

Other documents