2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. ARADA DEVON
  7. BK 735
BK 735

ARADA DEVON BK 735 User guide

  • Hello! I've reviewed the fitting guide for the ARADA Solid fuel kit BK 735. This document provides instructions on how to convert your stove for solid fuel use. It includes details on removing existing components and installing the new ceramic liners and retainer. I'm ready to answer your questions about this process!
  • What should I do before fitting the solid fuel kit?
    What components are included in the solid fuel kit?
    What parts do I need to remove before installing the solid fuel kit?
BK 735 Rev 02 ISSUE DATE : 14/01/2020
EN 13240:2011 +A2:2004
Solid fuel kit
fitting guide
Optional accessory instructions
Page 2 BK 735
1. Contents Of Kit :
1 no. Solid Fuel Retainer
1 no.
Solid Fuel Liner
(Ceramic—Left
hand)
1 no.
Solid Fuel Liner
(Ceramic—Right
hand)
2. Warnings :
IMPORTANT—Please ensure the appliance is cold and unlit before commencing fitting this
accessory kit.
Please refer to the main instruction booklet, relevant to your stove, for guidance and operation of
the appliance, when using solid fuel.
Arada Ltd will not be responsible for any consequential or incidental loss or injury however caused.
Please note, this accessory kit can be fitted once the appliance (stove) has been installed and
connected to the flue system, within the property.
Note, no technical knowledge is require to fit this kit.
Solid fuel kit fitting guide
Please Note—Shape Of Components May Vary Depending Upon Model
Page 3 BK 735
3. Fitting Procedure
Before starting this process, please ensure that the firebox is cold and all the ash bed has been
removed and cleaned.
Step 1 : Open the fire door & carefully remove the original fuel retainer. Keep this safe for
future use.
Step 2 : Take the operating tool and insert the fork end into the location slots within the
rear of the grate surround. Proceed to lift the grate surround up and with draw it from the firebox.
See figure 1.
Step 3 : Remove both of the base liner either side of the revolving grate. Again keep these
safe for future use in the even that the appliance is returned back to a wood only device.
Step 4 : Take one of the ceramic solid fuel base liners and place into the firebox along side
the revolving grate. Ensure the largest side of this liner is against the side liner. See figure 2.
Repeat the process for the remaining side.
Figure 1. Removing The Grate Surround
Operating
Tool
Base Liner
Grate
Surround
Solid fuel kit fitting guide
BK 735
Step 5 : Finally place the solid fuel retainer into position, engaging the two tabs within the
front brace of the appliance. See figure 3. The appliance is now set for solid fuel use.
Figure 2. Placement Of Base Liner
Base Liner
(Largest face against Side liner).
Side Liner
Figure 3. Solid Fuel Kit In Situ
Arada Ltd, The Fireworks, Weycroft Avenue, Axminster, Devon, United Kingdom EX13 5HU
Base Liners
Solid Fuel Retainer
www.aradastoves.com
Solid fuel kit fitting guide
BK736 Rev 03 ISSUE DATE: 16/01/2023
EN13240:2011 +A2:2004
Rear Heat Shield Kit
Fing Guide
Oponal Accessory Instrucons
PLEASE RETAIN THIS GUIDE FOR FUTURE REFERENCE
23
Page 2 BK 736
1. Contents Of Kit :
2 no. Heat Shield Mount Brackets
(Stainless Steel—Unpainted)
2. Warnings :
IMPORTANT—Please ensure the appliance is cold and unlit before commencing fitting this
accessory kit.
Please refer to the main instruction booklet, relevant to your stove, for guidance on the installation
and operation of the appliance.
Please consult Health & Safety guidelines for advice on handling heavy and / or large items. When
lifting, we recommend you always obtain assistance
Arada Ltd will not be responsible for any consequential or incidental loss or injury however caused.
Please note, this accessory kit can only be fitted prior to the appliance (stove) being installed and
connected to the flue system, within the property.
When handling the components of the kit, it is recommended to wear suitable gloves to prevent
hand injuries.
1 no.
Heat Shield (Stainless
Steel—Unpainted)
REAR HEAT SHIELD FITTING GUIDE
Holborn /
Ecoburn S3
OR
M Series
PLEASE NOTE : All fixings are factory fitted to the
appliance during manufacture.
Page 3
BK 736
PLEASE NOTE: Images show Ecoburn S3, however procedure is the same
regardless of appliance model.
3. Fitting Procedure :
Before starting this process, please ensure that the stove is cold and unlit
Step 1 : Working on the rear of the appliance, remove the 4x screw, indicated in figure 1.
Figure 2. Mounting Brackets
4 No. Fixing
Locations
Figure 1. Fixing Locations
Step 2 : Take one of the mounting brackets and fix in
place using 2no. Of the screws removed in step 1.
See figure 2.
Please note the orientation of the bracket
REAR HEAT SHIELD FITTING GUIDE
BK 736 Rev 03
Step 3 : Repeat step 2 for the remaining mounting bracket.
Step 4 : Take the heat shield and position the mounting slots over the corresponding lugs
on each side mounting bracket. Gently engage the lugs and push down, to locate the heat shield
onto the mounting brackets as shown in figure 3.
Step 5 : With the heat shield fitted, please observe the revised distance to combustible
materials, as stated in the instruction manual or product fiche on web site.
Figure 3. Heat Shield Layout
Flue Pressure Test Point Location.
This can be accessed whilst the
heat shield is in situ.
Detailed View Of Engaged Lug
Locating The Heat Shield
REAR HEAT SHIELD FITTING GUIDE
3. Fitting Procedure Continued:
Date Of Issue: 16/01/2023
Arada Ltd, The Fireworks, Weycroft Avenue, Axminster, Devon, United Kingdom, EX13 5HU
Technical Help : +44 (0)1297 632052, www.aradastoves.com
EN13240:2011 +A2:2004
Direct Air Kit
Fitting Guide
Optional Accessory Instructions
PLEASE RETAIN THIS GUIDE FOR FUTURE REFERENCE
BK737 Rev 03 ISSUE DATE: 17/01/2023 23
Page 2 BK 737
1. Contents Of Kit :
2. Warnings:
IMPORTANT—Please ensure the appliance is cold and unlit before commencing fitting this
accessory kit.
Please refer to the main instruction booklet relevant to your stove, for guidance and operation of
the appliance.
Please consult Health & Safety guidelines for advice on handling heavy and / or large items. When
lifting, we recommend you always obtain assistance
Arada Ltd will not be responsible for any consequential or incidental loss or injury however caused.
Please note, this accessory kit can only be fitted prior to the appliance (stove) being installed and
connected to the flue system, within the property.
When handling the components of the kit, it is recommended to wear suitable gloves to prevent
hand injuries.
2 no. M5 x 10mm Fixing Screws (Pozi)
1 no. Direct Air Plate (Stainless Steel—Unpainted)
2 no. M5 Penny Washer
DIRECT AIR KIT FITTING GUIDE
PLEASE NOTE: Images show Ecoburn S3, however the procedure is the same
regardless of appliance model.
3. Fitting Instructions:
Step 1 : Working at the rear of the appliance, locate and remove the 2no. Fixings as shown
below.
Step 2: Whilst at the rear, locate the base mount rails, as shown below. Please note, this is
not applicable for M-Series stoves.
Step 3: Take the direct air plate and slide the open end into the stove, resting the base of
the plate onto the base mount rails. Slide the plate forward until the rear fold makes contact with
the rear of the appliance.
For the M-Series stoves, ensure the plate is slid forward to make contact with the rear surface of
the stove. The front chamfered corners of the direct air plate rest upon the self adjusting brackets
at the front of the stove body. See pictures on adjacent page.
Page 3
BK 737
Base Mount Rails
(Not Applicable To M-Series)
DIRECT AIR KIT FITTING GUIDE
Remove Fixings
Indicated
Rear Of Stove
BK 737 Rev 03
PLEASE NOTE: M-Series Specific Only
Step 4: Secure in place using the M5 screws and M5 washers supplied, as shown above.
Fixings M5 Screw & Washer
Fixing Locations 2x
Date Of Issue: 17/01/2023
DIRECT AIR KIT FITTING GUIDE
Close Up Detail On
Underside Of Stove
Self Adjusting
Brackets
Chamfered Corner Of
Direct Air Plate
Direct Air Plate
Arada Ltd, The Fireworks, Weycroft Avenue, Axminster, Devon, United Kingdom, EX13 5HU
Technical Help : +44 (0)1297 632052, www.aradastoves.com
/