2. Guest
  3. 729828-P
729828-P

Guest 729828-P User manual

  • Hello! I've reviewed the installation instructions for the GUEST Spotlight kit 729828-P, intended for use with 296-5, 502, and 502A spotlights. The document outlines the necessary wiring connections for dual control, including the use of splitter wires, the control panel, and the interconnect cable. It also provides important safety precautions and details about the warranty. I'm ready to answer your questions about the product and its installation.
  • What is a Splitter wire sets used for?
    What is the length of the Interconnect Cable?
    What kind of power source is required?
MODEL 729828-P
DUAL STATION KIT
FOR 296-5, 502 AND 502A SPOTLIGHTS
INSTALLATION AND OPERATION
INSTRUCTIONS
IMPORTANT !
READ THESE INSTRUCTIONS BEFORE
INSTALLING THIS PRODUCT.
KEEP THESE INSTRUTIONS FOR FUTURE REFERENCE.
Downloaded from Arrow.com.
730364.doc 3429
2
Your Dual Station Kit includes the following:
1- Splitter wire sets (total of 6 colored wire sets, you will only need 5 sets for this assembly).
2- One control panel with Gasket, Hardware, and Instructions Manual
3- One Interconnect Cable, 15 ft long.
Mounting the Control Panel
Mount the Control panel according to its instruction manual.
Electrical connections
The Guest Model 502A spotlight has two types of wiring connections. They are:
• Control Cable wires - the small wires within the gray casing that carry your commands from the control panel
to the spotlight.
• Power supply wires- are Black (-) and Red (+) wires without connectors that bring 12-volt DC power into the
spotlight and into the control panel.
CAUTION!
DO NOT CONNECT THE CONTROL WIRES (with connectors)
TO ANY POWER SUPPLY WIRES.
DO NOT REVERSE THE RED (POSITIVE) AND BLACK (NEGATIVE) POWER WIRES.
This spotlight requires a power source of 12-volt DC power that is capable of supplying 10 amps of current even
when other equipment is operating. For best results, run two new power supply wires from the red (+) and black (-)
power wires of the light directly to the main 12-volt DC accessory panel. Install fuses and fuse holders as shown in
diagram. A 10-amp circuit breaker can be installed instead of an in-line 10-amp fuse.
1
2
4
3
Downloaded from Arrow.com.Downloaded from Arrow.com.
730364.doc 3429
3
If the light will be mounted less than 30 feet, (9m) from its power source, use 12-gauge (3mm) power supply wires. If
the distance will be more than 30 feet, (9m) use 10 gauge (5mm) wires.
An In-line 2amp fuse and holder should be installed on the red 22 awg power wire for each control.
Complete the wiring connections using the items included in kit as shown below:
Foam Gasket
18-22 gauge. Butt Connector
10 Amp Fuse
(or circuit breaker)
Black
12 volts DC
Red
12 volts DC
1.
Connect the wires from the spotlight
to SAME colors of Splitter Wire sets
on this end
2.
Connect the Wires of theTwo Controls to
SAME Wire Colors of the 15 ft long
Interconnect Cables
18-22 guage. Butt Connector
Black
12 volts DC
Red
12 volts DC 2 Amp
Fuse
Do not use
blue wires
RED
BROWN
GREEN
BLACK
WHITE
18-22 gauge. Butt Connector
Black
12 volts DC
Red
12 volts DC 2 Amp
Fuse
Do not use
blue wires
RED
BROWN
GREEN
BLACK
WHITE
To # 1
To # 2
To # 3
To # 4
OR
It can be connected here
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.
730364.doc 3429
4
Precautions
DO NOT look directly into the spotlight or floodlight while it is operating.
DO NOT cover the light with a fabric cover or any other flammable material. Accidental activation may result in a fire
hazard.
DO turn the spotlight toward the control station when not in use. If the spotlight is accidentally activated during
daylight, the operator will be more likely to notice and turn the spotlight off before draining a battery.
LIMITED WARRANTY
For one (1) year from the date of original purchase, The Guest Co. will, at its discretion, repair or
replace for the original consumer, free of charge, any parts found defective in material or
workmanship. All transportation charges under this warranty must be borne by the consumer.
Proof of purchase is required: A computerized register receipt is required. Hand-written receipts
are not accepted for warranty proof of purchase. In the absence of a receipt, warranty period
will be calculated from date of manufacture printed or stamped on the product.
There is no other expressed warranty. Implied warranties, including those of merchantability and
fitness for a particular purpose, are limited to one year from the date of purchase. This is the
exclusive remedy and consequential damages are excluded where permitted by law.
Tel: (707) 226-9600 Email: [email protected]
Fax: (707) 226-9670 Website: www.marinco.com
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.
/