Altronix ALT-NETWAY1DWPH Installation guide

Category
Security camera accessories
Type
Installation guide

Altronix ALT-NETWAY1DWPH is an outdoor single port Hi-PoE injector that provides power and data for PoE compliant cameras and edge devices up to 100 meters away. It features surge protection, auto-crossover connectivity, and a compact NEMA 4X, IP66 rated enclosure for outdoor use. With a maximum power output of 60W, the ALT-NETWAY1DWPH can support Hi-PoE devices like PTZ cameras and high-resolution IP cameras. It also supports IEEE 802.3at (30W) and IEEE 802.3af (15W) compliant devices, making it a versatile solution for various PoE applications.

Altronix ALT-NETWAY1DWPH is an outdoor single port Hi-PoE injector that provides power and data for PoE compliant cameras and edge devices up to 100 meters away. It features surge protection, auto-crossover connectivity, and a compact NEMA 4X, IP66 rated enclosure for outdoor use. With a maximum power output of 60W, the ALT-NETWAY1DWPH can support Hi-PoE devices like PTZ cameras and high-resolution IP cameras. It also supports IEEE 802.3at (30W) and IEEE 802.3af (15W) compliant devices, making it a versatile solution for various PoE applications.

NetWay1DWP
Outdoor Single Port Hi-PoE Injector for
Standard and Enhanced Power Network Infrastructure
Power over the Ethernet
Rev. 112713 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Installation Guide
I.T.E. 43KC
- 2 - NetWay1DWP Installation Guide
Table of Contents:
Overview .................................................................pg. 3
Features .................................................................pg. 3
Installation Instructions ......................................................pg. 3
Technical Specifications .....................................................pg. 4
Typical Applications ........................................................pg. 5
Wall Mount Installation ......................................................pg. 7
Pole Mounting Using Optional Pole Mount Kit PMK1 ...............................pg. 7
Enclosure Dimensions ............................................................. pg. 8
NetWay1DWP Installation Guide - 3 -
Overview:
Altronix NetWay1DWP Outdoor Single Port Midspan Injector provides Hi-PoE (60W) power and passes data for
PoE compliant cameras/edge devices. Cameras/edge devices may be located up to 100m from the unit.
Features:
Agency Listings:
UL 60950-1 Information Technology Equipment.
UL 60950-22 Information Technology Equipment
to be installed Outdoors.
CE European Conformity.
Input:
115VAC, 60Hz, 1.2A or 230VAC, 50/60Hz, 0.75A.
Power Output:
Maximum power: Hi-PoE (60W) power product
using all 4 pairs for 60W.
IEEE 802.3at (30W) and
IEEE 802.3af (15W) compliant.
Integral surge protection.
Ethernet:
Connectivity: RJ45, auto-crossover.
Wire type: 4-pair Cat-5 or better structured cable.
Distance: up to 100m.
• Speed: 10/100/1000Mbps, half/full duplex,
auto negotiation.
LEDs:
LED1: PoE active. LED2: AC Power present.
Environmental:
Operating Temperature:
30W: – 30ºC to 70ºC (– 22ºF to 158ºF).
60W: – 30ºC to 55ºC (– 22ºF to 131ºF).
Storage Temperature:
– 30ºC to 85ºC (– 22ºF to 185ºF).
Humidity: 20 to 85%, non-condensing.
Applications:
Provides PoE/PoE+ and Hi-PoE for cameras/devices.
Mechanical:
NEMA 4X, IP66 Rated enclosure for outdoor use.
• Dimensions (H x W x D approx.):
9.5” x 7.32” x 4.92”
(241.3mm x 185.9mm x 125mm).
Models:
• NetWay1DWP: Outdoor Single Port Hi-PoE Injector.
• NetWay1DWPH: Outdoor Single Port Hi-PoE
Injector, enclosure with three (3) 5/8” wiring
inlets, includes NEMA rated glands.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
1. Remove circuit board from enclosure prior to drilling NetWay1DWP (do not discard hardware).
Note: Take care to assure that hardware will not interfere with components of the circuit board.
2. NetWay1DWP: Mark and drill desired inlets on the enclosure to facilitate wiring (Fig. 2, pg. 4).
Maximum UL Listed NEMA type 4X rated fittings to be used is 1/2”, follow manufacturer’s specifications
for the appropriate size opening.
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
UL Listed NEMA type 4X rated conduit connector/hubs shall be used for the appropriate size inlets.
NetWay1DWPH is pre-drilled with three (3) pre-drilled inlet holes for wiring.
3. Clean out the inside of enclosure before remounting circuit board.
4. Switch circuit breaker to the OFF position.
5. Connect AC power from a UL approved circuit breaker to the terminals marked
[L] and [N], connect ground to the terminal marked [G] (refer to Fig. 1 on right).
6. Mounting NEMA 4X rated enclosure:
Wall mount: Mount unit in desired location. Mark and drill holes to line
up with the top and bottom holes of the enclosure flange. Secure enclosure
with appropriate fasteners (e. g. screws and anchors; bolts and locking
nuts, etc.) which are compatible with mounting surface and are of
sufficient length/construction to ensure a secure mount (Fig. 4, pg. 7).
Pole Mount: refer to page 7.
Note: All inlets for conduit fittings should be on the bottom of the enclosure.
7. Mount circuit board in enclosure with hardware.
8. To facilitate wire entry utilize weather-tight NEMA rated connectors (supplied), bushings and cable.
9. Connect structured cable from UL Listed ethernet switch or video server to RJ45 jack marked [IN] on
NetWay1DWP/NetWay1DWPH (Fig. 3, pg. 5).
10. Connect structured cable from camera/device to RJ45 jack marked [OUT] on NetWay1DWP/
NetWay1DWPH/ (Fig. 3, pg. 5).
11. Switch circuit breaker to the ON position.
LGN
115VAC/230VAC
Input
Line Neutral
Ground
Fig. 1
- 4 - NetWay1DWP Installation Guide
Technical Specifications:
Parameter Description
Number of Ports One (1) Hi-PoE (60W) or IEEE 802.3at (30W) and IEEE 802.3af (15W) compliant.
Input Power
Requirements 115VAC, 60Hz, 1.2A or 230VAC, 50/60Hz, 0.75A.
Environmental
Conditions
Operating Ambient Temperature:
30W: 70ºC (158ºF).
60W: 55ºC (131ºF).
Storage Temperature: 30ºC to 85ºC (22ºF to 185ºF).
Relative humidity: 20 to 85%, non-condensing.
Operating Altitude: 304.8 to 2,000m.
Regulatory
Compliance
UL 60950-1 Information Technology Equipment.
UL 60950-22 Information Technology Equipment to be installed Outdoors.
CE European Conformity.
Weights (approx.) Product: 3.7 lb. (1.68 kg) | Shipping: 5 lb. (2.27 kg)
Fig. 2 - Bottom of enclosure
0.875”
22.2mm
4.25”
108mm
2.4375”
61.9mm
1.125”
28.6mm
1.125”
28.6mm
1.25”
31.8mm
Suggested area
for Inlets
NetWay1DWP Installation Guide - 5 -
Typical Applications:
Fig. 3
Ethernet Switch
Video
Monitor
NVR/Network Server
OUT IN
CAT-5 or
Higher
100m
CAT-5 or
Higher
100m
Camera/
Device
115VAC/230VAC
Input
LGN
Line Neutral
Ground
- 6 - NetWay1DWP Installation Guide
Notes:
NetWay1DWP Installation Guide - 7 -
Wall Mount Installation
1. Place unit at desired location and secure with mounting
screws (not included) (Fig. 4, pg. 7).
Fig. 4
Pole Mounting Using Optional Pole Mount Kit PMK1 (not included):
This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK1
is intended for use with Altronix outdoor rated power supplies or accessories housed in WP1, WP2, WP3 and WP4
enclosures. Brackets are designed for use with the Wormgear Quick Release Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 5, pg. 7).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 6, pg. 7 and Fig. 8, pg. 7).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 7, pg. 7).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting bracket
(Fig. 5, pg. 8).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 7, pg. 7).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 5, pg. 7).
7. Clip excess straps.
Fig. 5 Fig. 6 Fig. 7
Fig. 8
Fig. 9
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 9a
5” (127mm) square pole
- 8 - NetWay1DWP Installation Guide
Mechanical Drawing and Dimensions (H x W x D approx.):
9.5” x 7.32” x 4.92” (241.3mm x 185.9mm x 125mm)
4.25” (108mm)
6.0” (152.4mm)
6.75” (171.5mm)
6.27” (159.3mm)
8.75” (222.2mm)
8.0” (203.2mm)
9.5” (241.3mm)
10-32 X 0.25” (6.4mm)
4 Places
4.35” (110.5mm)
8.75” (222.2mm)
1.38”
(35.1mm) 3.54” (89.9mm)
7.32” (185.9mm)
9.32” (236.7mm)
304 Stainless Steel Piano Hinge
4.92” (125mm)
4.0” (101.6mm)
0.312” (7.9mm) TYP
4 Places
316 Stainless Steel
Padlock Latch Attached
0.375” (9.5mm)
Padlock Eye
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IINetWay1DWP H19U MEMBER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Altronix ALT-NETWAY1DWPH Installation guide

Category
Security camera accessories
Type
Installation guide

Altronix ALT-NETWAY1DWPH is an outdoor single port Hi-PoE injector that provides power and data for PoE compliant cameras and edge devices up to 100 meters away. It features surge protection, auto-crossover connectivity, and a compact NEMA 4X, IP66 rated enclosure for outdoor use. With a maximum power output of 60W, the ALT-NETWAY1DWPH can support Hi-PoE devices like PTZ cameras and high-resolution IP cameras. It also supports IEEE 802.3at (30W) and IEEE 802.3af (15W) compliant devices, making it a versatile solution for various PoE applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI