Accessories
Preparation – Uninstall AMD Radeon HD 6990 stock cooler
MX-4 (Thermal Compound 0.8 g)
Thermal Pad
Spacers (2 mm)
Accelero Twin Turbo 6990
Installation Manual
Instalační příručka: www.arctic.ac/fileadmin/att6990/manual_cz.pdf
Telepítési kézikönyv: www.arctic.ac/fileadmin/att6990/manual_hu.pdf
Instrukcja montażu: www.arctic.ac/fileadmin/att6990/manual_pl.pdf
Installatiehandleiding: www.arctic.ac/fileadmin/att6990/manual_nl.pdf
Montageanleitung: www.arctic.ac/fileadmin/att6990/manual_de.pdf
Guide d’installation: www.arctic.ac/fileadmin/att6990/manual_fr.pdf
Manual de instalación: www.arctic.ac/fileadmin/att6990/manual_es.pdf
Manual de Instalação: www.arctic.ac/fileadmin/att6990/manual_pt.pdf
Installationsmanual: www.arctic.ac/fileadmin/att6990/manual_se.pdf
x 1
x 8
x 1 x 1
1 2
Keep all the original screws and parts for further installation steps.
Installation of Accelero Twin Turbo 6990
x 1 x 1
3
4
1
3
2
5 Remove all original thermal pads and clean the GPU cores thoroughly.Remove all original thermal pads and clean the GPU cores thoroughly.
Place the thermal pads according to the cut-out areas on the plastic
film.
To avoid damaging the card, remove the PCB and back plate
together slowly until the thermal pad and thermal compound start
to disengage from the stock cooler.
Align the heatsink to the mounting plate with a ruler.Align the heatsink to the mounting plate with a ruler.4
EN
Warranty
This ARCTIC Product includes a six-year limited warranty. Please visit warranty.arctic.ac for further details.
If the cooler is installed for a second time, we highly recommend using MX-4 from ARCTIC. Only MX-4 guarantees optimal performance in combination with the surface of our heatsinks.
Thermal Compound
How to unplug PCI-E
© 2011 ARCTIC (HK) Ltd. All Rights Reserved.
No part of this manual including the products described in it, may be reproduced, transmitted, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purpose, without the
express written permission of ARCTIC (HK) Ltd. In no event shall ARCTIC its directors or employees be liable for any indirect damages, incidental or consequential damages arising from any defect or error in this manual or product.
ARCTIC Switzerland
Huobstrasse 4, 8808 Pfäffikon, Switzerland
www.arctic.ac
5 6 Apply half of the MX-4 for each GPU core.
7 8
9 10
11 12
Make sure the nuts have passed through the VGA PCB completely.Make sure the nuts have passed through the VGA PCB completely.
Install the main cooler to the VGA card by fastening each of the
original screws (A B C D E F) with 3 clockwise rotations. Do
not fasten the screws completely.
C
F
B
A
E
D
Align the VR heatsink holes (G, H and I). Fasten each of the original
screws alternately (G H I) with 1 to 2 clockwise rotations. Repeat
until all screws are tightened. Do not fasten any screw completely in
one step.
G
H
I
Install the mounting onto the VGA card by fastening each of the
original screws alternately (a b c d e f g h) with 2 clockwise
rotations. Repeat until all screws are tightened. Do not fasten any
screw completely in one step.
Finish fastening each of the original screws (A B C D E F) with
1 clockwise.
c
a
d
b
e
g
h
f
D
E
A
F
B
C
Place back the PCB and back plate together onto the cooler.Place back the PCB and back plate together onto the cooler.
/