ADTRAN IP 712 User manual

6AOSAG0001-31A

April 2011

IP 700 Series

Phone

Administrator

Guide

Firmware Version 2.x.x

Trademarks ADTRAN IP 700 Series Phone Administrator Guide

Trademarks

Any brand names and product names included in this manual are trademarks, registered trademarks, or

trade names of their respective holders.

To the Holder of the Manual

The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change

the contents without prior notice.

In no event will ADTRAN be liable for any special, incidental, or consequential damages or for

commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.

Intended Audience

This document is intended for ADTRAN IP 700 Series phone administrators.

Software Licensing Agreement

Each ADTRAN product contains a single license for ADTRAN-supplied software. Pursuant to the

Licensing Agreement, you may: (a) use the software on the purchased ADTRAN device only and (b) keep

a copy of the software for backup purposes. This Agreement covers all software installed on the system, as

well as any software available on the ADTRAN website. In addition, certain ADTRAN systems may

contain additional conditions for obtaining software upgrades.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

Printed in U.S.A.

Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

IP 700 Series Phone Administrator Guide Software Licensing Agreement

Conventions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption or damage to

equipment.

Warnings provide information that could prevent injury or endangerment to human

life.

Safety Instructions ADTRAN IP 700 Series Phone Administrator Guide

Safety Instructions

When using your telephone equipment, please follow these basic safety precautions to reduce the risk of

fire, electrical shock, or personal injury:

1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a

wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There is a remote

risk of shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and batteries indicated in the manual. Do not dispose of

batteries in a fire. They may explode. Check with local codes for special disposal instructions.

5. The socket-outlet shall be installed near the equipment and shall be easily accessible.

Save These Important Safety Instructions

IP 700 Series Phone Administrator Guide FCC Radio Frequency Interference Statement

FCC Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial or residential environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio frequencies.

Canadian Emissions Requirements

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus

as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the

Department of Communications.

Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques

de Class B prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee

par le ministre des Communications.

Product Safety and Electromagnetic Compatibility (EMC) Standards Table

P/N and Name Standards

1200769E1#X

1200770E1#X

IP 706 Series Phone

IP 712 Series Phone

FCC Part 15, Class B

ICES-003

EN 55022 Class B

EN 55024

EN 61000-3-2

EN 61000-3-3

UL/CUL 60950-1

IEC 60950-1

EN 60950-1

General Information ADTRAN IP 700 Series Phone Administrator Guide

General Information

The IP 706 and IP 712 phones are designed to operate in both Key Systems and private branch exchange

(PBX) Systems. The IP 706 or IP 712 phone will be aware of its operating mode and respond

appropriately. Certain features may or may not be offered in certain modes. This manual notes when

certain features are only supported in one system. Refer to the specific feature for more information.

Certified IP PBX Systems

The IP 700 Series phones have been officially tested and certified with the following IP PBX switches.

Phone certification with other systems is ongoing and, therefore, this may not be the most recent list. Refer

to ADTRAN’s website at www.adtran.com/phones

for the latest information.

NetVanta 7000 Series

NetVanta Unified Communications

Service and Warranty

For information on the service and warranty of ADTRAN products, visit the ADTRAN website at

http://www.adtran.com/support

.

Related Documentation

For more specific information regarding the IP 706 and IP 712 model phones, refer to ADTRAN’s website

at www.adtran.com/phones

.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2. Assembly and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Unpacking the Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Assembling the Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Attaching the Desk Stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting the Handset and Headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Headset Interface Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Headset Interface Off-Hook Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3. Connecting the Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Local Power Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Inline Power Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Power Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4. Managing IP 700 Series Phones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Precedence of Parameter Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5. Setting the Minimum Required Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6. Using the Administrator’s Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Locating the IP Address of the Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Setting the Phone’s IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Accessing the Administrator’s Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Navigating the Phone Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Phone Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

SIP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Line Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Phone Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Button Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

BLF Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Speed Dial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Time Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

SPRE Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Dial Plan Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Load Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Reset Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7. Automating Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

DHCP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Configuration Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

8. Configuring Common Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Setting the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Configuring Proxy and Registrar Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Defining Line Registrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Setting the Realm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Setting the Domain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table of Contents ADTRAN IP 700 Series Phone Administrator Guide

Assigning Line Key Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Configuring Other Server and SIP Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Defining Call Handling Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Customizing the Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Modifying the Splash Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Bitmap Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

9. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Basic Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Advanced Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Accessing the Phone Status Display Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

General Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Network Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Line Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Audio Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Keypad Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

LCD Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

LED Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Ping Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Backlight Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Resetting the Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Restoring Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Deleting a Personal Phone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Appendix A. Configuration and Line Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Line Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Appendix B. Dial Plan Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Dial Plan Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Default External Dial Plan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Default PBX Dial Plan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Appendix C. Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

List of Figures

Figure 1. Parts Included with Your IP Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 2. Assembling the Desk Stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 3. Connecting the Handset and Headset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 4. Connecting to the Local Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 5. Connecting to the Inline Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 6. Phone Summary Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 7. Network Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 8. SIP Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 9. Line Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 10. Phone Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 11. Button Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 12. BLF Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 13. Speed Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 14. Time Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 15. SPRE Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 16. Dial Plan Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 17. Load Certificate File Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 18. Reset Phone Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 19. Line Key Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

List of Figures ADTRAN IP 700 Series Phone Administrator Guide

List of Tables

Table 1. Headset Interface Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 2. Minimum Parameters Required for Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 3. Guidelines for Assigning Line Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 4. Realm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 5. Line Key Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table 6. Server Parameters and SIP Options Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Table 7. Call Handling Options Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Table 8. Phone Customization Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Table 9. Basic Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Table 10. Advanced Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 11. LCD Test Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Table 12. Configuration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 13. Line Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Table 14. Dial Plan Syntax Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Table 15. External Dial Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Table 16. PBX Dial Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

List of Tables ADTRAN IP 700 Series Phone Administrator Guide

1. INTRODUCTION

This guide explains how to administer the IP 706 and IP 712 phones from ADTRAN. ADTRAN IP phones

are full-duplex, handsfree IP phones that offer business-class features, such as multiple call appearance,

hold, transfer, and conferencing. The phones are simple to use while offering the latest advances in

telephony systems. Updates and new features are downloaded to the phones without intervention or the

need for phone replacement.

This guide contains the following sections:

• Assembly and Installation on page 14

• Connecting the Power Source on page 17

• Managing IP 700 Series Phones on page 19

• Setting the Minimum Required Parameters on page 20

• Using the Administrator’s Web Interface on page 22

• Automating Configuration on page 37

• Configuring Common Features on page 39

• Troubleshooting on page 49

Assembly and Installation ADTRAN IP 700 Series Phone Administrator Guide

2. ASSEMBLY AND INSTALLATION

The following sections list the items included in your phone shipment and provide instructions for

assembling the IP 706 and IP 712 phones. For questions dealing with missing parts or difficulty in

assembly, contact your ADTRAN reseller.

Unpacking the Phone

As you carefully unpack your phone, be sure you have received each item in the following list:

• IP 706 or IP 712 phone console

• Audio handset

• 9-foot coiled handset cord

• Ethernet cable

• Adjustable desk stand and bracket

• Quick start guide

The following items are available separately:

• Wallmount kit, black (P/N 1200808E1#B)

• Single port Power over Ethernet (PoE) power supply, North America (P/N 1200809E1)

• Single port PoE power supply, International (P/N 1200809E#IN)

Figure 1. Parts Included with Your IP Phone

IP 712 Console

Handset and

Cord

Network (LAN)

Cable

Desk Bracket

and Stand

Optional

Wallmount Kit

Optional

PoE Power Supply

Quick Start

Guide

P

OWER

J

1

D

A

T

A

&

P

W

R

J

2

D

A

T

A

+

-

12

ABC

4

GHI

3

DEF

5

JKL

6

MNO

7

PQRS

8

TUV

9

WXYZ

*

0

#

Directories

Messages

Transfer

Conference

Hold

Goodbye

Menu

OK

Cancel

IP 700 Series Phone Administrator Guide Assembly and Installation

Assembling the Phone

The IP 706 and IP 712 phones require minimal assembly. The parts that must be assembled include the

desk stand and handset.

Attaching the Desk Stand

1. Insert the stand through the bracket (rotating it so it fits through the opening).

2. Once through the bracket opening, rotate the stand back and pull it toward the bracket until seated.

3. Make sure the stand is properly oriented within the bracket as shown in Figure 2 below.

4. With the desk stand assembled, insert the top two tabs into the corresponding slots on the phone

back.

5. Insert the remaining tabs in the order shown in Figure 2 below. Tabs 4 and 5 must be pressed

inward to snap into the slots.

6. Once the desk stand is installed, use the sliding latch on the back to adjust the phone to the

preferred tilt. To remove the desk stand for wall mounting purposes, simply push in the tabs along

the side and lift the desk stand from the back of the phone.

Figure 2. Assembling the Desk Stand

The IP 706 and IP 712 phones may be wall mounted using the optional wallmount kit

(P/N 1200808E1). For wall mounting instructions, refer to the IP 700 Series Wallmount

Kit Quick Start Guide shipped with the kit.

5

3

2

4

1

Bracket

Top

Stand

Desk Stand

Unit

Phone Back

Assembly and Installation ADTRAN IP 700 Series Phone Administrator Guide

Connecting the Handset and Headset

1. Using the provided 9-foot coiled handset cord, insert one end into the jack in the bottom of the

handset. Insert the other end into the jack on the back of the phone console labeled with the

handset icon as shown in Figure 3 below. Place the handset on the handset cradle once installed.

2. Optional. Connect your headset to the jack in the back of the phone console labeled with the

headset icon as shown in Figure 3 below. There are many types of headsets that can be used with

the IP 706 or IP 712 phone. For a list of compatible headsets for the IP phones, refer to the

ADTRAN website at www.adtran.com/phones

. Once the headset is connected, the headset feature

is ready to use.

Figure 3. Connecting the Handset and Headset

Headset Interface Pinout

The pinout for the optional headset is available in Table 1 below. Refer to ADTRAN IP 700 Phone Wireless

Headset Compatibility (ADTRAN’s Knowledge Base article 3059) for a list of wireless headsets that have

been approved for use with ADTRAN IP 700 Series phones.

Headset Interface Off-Hook Detection

Off-hook detection is achieved by providing battery across the TX+ and TX- pair and monitoring for loop

current. You can simulate off-hook by connecting a 1.5 k resistor across these pins.

Table 1. Headset Interface Pinout

Pin Function

1TX-

2RX-

3RX+

4TX+

Optional

Headset

Handset

IP 700 Series Phone Administrator Guide Connecting the Power Source

3. CONNECTING THE POWER SOURCE

Once the IP 706 and IP 712 phones have been assembled, it is necessary to connect the phones to a power

source and the phone system. There are two options available to supply power to your IP phone. Use the

Local Power Option if your wall jack is not PoE enabled. This option requires using the optional PoE

power supply (P/N 1200809E1 or P/N 1200809E#IN). If your wall jack is PoE enabled, use the Inline

Power Option which does not require the optional PoE power supply. Use the following steps to complete

these tasks.

Local Power Option

Use the Local Power Option if your jack is NOT PoE enabled. If your jack is PoE enabled, a PoE power

supply is not necessary.

1. Connect one end of the included Ethernet cable to the Ethernet jack on the back of the phone.

2. Connect the remaining end to the

J1 DATA AND POWER port on an appropriate PoE-enabled

device.

3. Connect one end of a second Ethernet cable (not included) to the

J2 DATA port on the PoE device.

4. Connect the remaining end of the second Ethernet cable (not included) to the non-PoE wall jack.

5. Connect the PoE device to the wall outlet.

Figure 4. Connecting to the Local Power Source

Network connectivity is provided through the wall jack, allowing an optional PC

connection through the IP phone. If the IP phone is disconnected from either the

network or power source, network connectivity from the phone to the attached PC

will be lost.

P

O

W

E

R

J1

DATA & PWR

J2

DATA

Optional

PoE Power Supply

Non-PoE Wall

Jack

Optional PC

Connection

5

3

2

1

4

Connecting the Power Source ADTRAN IP 700 Series Phone Administrator Guide

Inline Power Option

1. Connect one end of the included Ethernet cable to the Ethernet jack on the back of the phone.

2. Connect the remaining end of the Ethernet cable to the PoE wall jack.

Figure 5. Connecting to the Inline Power Source

Power Specifications

The IP 706 and IP 712 phones support the following powering specifications:

• IEEE 802.3af powering on signal or spare pairs independent of polarity

• Presents a valid IEEE 802.3af detection signature on both the signal and spare pairs

• Presents a Class 2 signature when a valid signature is required

• Draws less than 6.49 W of power under normal operating conditions

Network connectivity is provided through the PoE wall jack, allowing an optional

PC connection through the IP phone.

All powering over telecommunication wiring must be via UL-listed power supplies with

outputs of 48 VDC  1 percent, 350 mA maximum.

Optional PC

Connection

PoE Wall

Jack

1

2

IP 700 Series Phone Administrator Guide Managing IP 700 Series Phones

4. MANAGING IP 700 SERIES PHONES

There are multiple ways to manage ADTRAN IP 700 Series phones, each providing a different

management approach. Choose the method that best suits your situation:

• Password-protected administrator’s Web interface (Phone Manager) to view and change current settings

on a single phone.

• Phone’s user interface to view and modify current settings locally.

• Configuration files to automatically download parameters upon phone startup and update firmware.

• Dynamic Host Configuration Protocol (DHCP) to set a limited number of parameters including the

location of configuration files.

Administrators can choose to administer phones individually using the Web interface (refer to Using the

Administrator’s Web Interface on page 22). Configuring a large number of phones can be accomplished via

configuration files that automatically download at startup (refer to Automating Configuration on page 37).

In certain situations, it may be necessary to set critical parameters manually using the phone’s user

interface (refer to Locating the IP Address of the Phone on page 22).

Precedence of Parameter Sources

When building the set of phone parameters, it is possible to have multiple sources for the same parameter.

Therefore, it is important to understand the order of precedence assigned to each source. The following list

indicates this precedence:

1. Parameters manually entered using either the phone’s user interface (Phone Settings) or via the

administrator’s Web interface (Phone Manager) have the highest priority and override parameters

received from all other sources. Use Restore Factory Defaults on the phone or administrator’s

Web interface to clear all values that have been manually set using the Phone Settings menu.

2. Parameters received in a configuration file override those received from DHCP and defaults.

3. Parameters returned by DHCP (if it is enabled) override default settings.

4. Default parameters are used if no other source is available.

Setting the Minimum Required Parameters ADTRAN IP 700 Series Phone Administrator Guide

5. SETTING THE MINIMUM REQUIRED PARAMETERS

At a minimum, the following parameters must be specified for the IP 700 Series phones to operate on a

network server. The parameters not included in the table can usually be left at their default values.

However, for optimal operation, it is recommended that you review all parameters. For a complete list of

parameters and additional information about these settings, refer to Appendix A on page 57.

Table 2. Minimum Parameters Required for Operation

Parameter Description Source

IP Address (IpAddress) Specifies the IP address for the phone. DHCP

Phone Interface

Web Interface

Subnet Mask (SubNetMask) Indicates the network mask for the phone. DHCP

Phone Interface

Web Interface

Gateway (GatewayAddress) Specifies the gateway address for the phone. DHCP

Phone Interface

Web Interface

File Transfer Protocol (FTP),

Hypertext Transfer Protocol

(HTTP), HTTP Secure (HTTPS),

or Trivial File Transfer Protocol

(TFTP) Server Address

(FtpServers, HttpServers,

HttpsServers, or TftpServers)

Specifies either FTP, HTTP, HTTPS, or TFTP

server. If a server is unavailable, the phone

goes through the list until a working server is

found. Either FtpServers, HttpServers,

HttpsServers, or TftpServers may be specified

as the non-null value used to determine the

download method for configuration files.

DHCP

Phone Interface

Web Interface

DNS Server IP Address

(DnsAddress)

This must be configured unless numeric IP

addresses are supplied for all parameters and

fully qualified domain names (FQDNs) are not

used.

DHCP

Config File

Phone Interface

Web Interface

Proxy Server

(ProxyServer.z.Address.y)

An IP address, FQDN, or domain name for one

or more proxy servers. If only a proxy domain

name is specified, a Session Initiation Protocol

(SIP) SRV record for the proxy must be

configured in the DNS server and the

ProxyServer.z.Port.y must be set to 0.

Config File

Web Interface

Registrar Server

(RegServer.z.Address.y)

An IP address, FQDN, or domain name for one

or more registrar servers. If only a proxy domain

name is specified, a SIP SRV record for the

registrar must be configured in the DNS server

and the RegServer.z.Port.y must be set to 0.

Config File

Web Interface

Line Key Configuration

(Button.z.Type, Button.z.Line,

Button.z.Label)

At least one key must be configured as a line

key to make or receive calls.

Config File

Web Interface

User Name (Reg.x.AuthUserId) User name used to register a phone line with

the registrar.

Config File

Web Interface

Password

(Reg.x.AuthPassword)

Password used to register a phone line with the

registrar.

Config File

Web Interface

Page is loading ...

ADTRAN IP 712 User manual

This manual is also suitable for

ADTRAN IP 712 User manual

Related papers

Other documents