Marathon Computer FTvirtual IBM BladeCenter User manual

Marathon Technologies FTvirtual

Server

TM

and IBM BladeCenter

TM

Installing and Configuring a Fault-Tolerant Windows

Environment for Mission Critical Applications

Marathon Technologies Corporation

www.marathontechnologies.com

888.682.1142

Notices

Marathon Technologies Corporation reserves the right to make

improvements to this guide and the product it describes at any

time and without further notice.

Copyright

reserved.

This guide is copyrighted, and all rights are reserved. No part of

this guide or the products it describes may be reproduced by any

means or in any form, without prior consent in writing from

Marathon Technologies Corporation.

Printed in the U.S.A.

U.S. Patent Numbers: 5,600,784; 5,615,403; 5,787,485;

5,790,397; 5,896,523; 5,956,474; 5,983,371; 6,038,685;

6,205,565; and 6,728,898.

European Patent Numbers: EP0974912; EP0731945;

EP0993633; EP0986784; and EP1000397.

Other patents pending.

Software Copyright Notice

The software described in this document is covered by the

following copyright:

Trademark Notice

Endurance, Marathon Assured Availability, Marathon

FTvirtual Server, and the Marathon logo are either regis-

tered trademarks or trademarks of Marathon Technolo-

gies Corporation in the United States and/or other

countries.

Microsoft, MS-DOS, and Windows are registered trade-

marks of Microsoft Corporation in the United States and/

or other countries.

IBM eServer BladeCenter and IBM are registered trade-

marks of the International Business Machines Corpora-

tion in the United States and/or other countries.

All other brands and product names are trademarks of

their respective companies or organizations.

Software Revision

The revision of the software that this document supports is

Revision 6.1.1.

This section describes the technical changes made in

this edition of the Marathon Technologies FTvirtual Serv-

er

TM

and IBM eServer BladeCenter

TM

- A Fault-Tolerant

Environment for Mission Critical Windows Applications

application note. Minor changes and editorial corrections

may also be included that are not identified.

Summary of changes

Summary of changes for

Marathon Technologies FTvirtual Server and IBM

eServer BladeCenter

TM

- A Fault-Tolerant Environment

for Mission Critical Windows

as created or modified on 9/2/05.

September 2005, First Edition

1.0.0

Marathon Technologies Corporation 1

Contents

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

Software Copyright Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

Trademark Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Software Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

September 2005, First Edition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

CHAPTER 1 Introduction

Fault-Tolerant Computing for Mission Critical Windows Applications . . . . . . . . . . . . . . . . . . . . 1

The Trend Toward Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Mission-Critical Blades: The Need For Fault Tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Marathon FTvirtual Server - Fault-Tolerance Through Software . . . . . . . . . . . . . . . . . . . . . . . . 3

Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CHAPTER 2 Planning and Preparation

Planning the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

FTvirtual Server Boot Disk Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Network Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CoServer and Switchbay Network Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure - Sample BladeCenter Network Adapter Switchbay Map. . . . . . . . . . . . . . . . . . . . . 7

Network Adapter Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table - 4 NIC Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table - 3 NIC Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table - 3 NIC Alternate Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table - 2 NIC Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Preparing to Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

BladeCenter Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

FTvirtual Server and Blade Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Identifying Network Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Mapping the Switchbays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table - Adapter PCI-to-Switchbay Mappings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Contents

2 Marathon Technologies Corporation

CHAPTER 3 Installing the Endurance Software

Major Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Windows Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Installing Windows on the CoServers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Event Log Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Disk Partitioning and Formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installing the FTvirtual Server Boot Disk on a Physical Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Installing Endurance Software on the CoServers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Before You Begin the Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CoServer 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Starting the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Specify the Location of the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Configure the Network using the Endurance Network Setup Wizard . . . . . . . . . . . . . . . . . . . . 21

Table - Suggested CoServer1 CLink IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

CoServer 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table - Suggested CoServer2 CLink IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Installing Windows on and Configuring the FTvirtual Server . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Select CoServer Devices for FTvirtual Server Use and Configure the FTvirtual Server Disk . 34

Install Windows on the FTvirtual Server Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Finish the Windows Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Install the Endurance FTvirtual Server Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Specify the Location of the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Finish the FTvirtual Server Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Verifying the FTvirtual Server Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

What to do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Marathon Technologies Corporation 1

CHAPTER 1 Introduction

Fault-Tolerant Computing for Mission Critical

Windows Applications

The Trend Toward Blades

Blade configurations like the IBM BladeCenter have become popular

because they provide several key advantages over conventional pedestal

or rack-mounted servers. These advantages include:

• Flexibility and Ease of Installation

Because blades get their electrical power and network interconnections

from the chassis, adding processing power to an existing chassis is as

simple as inserting the blade and configuring its software and network

address. No additional cabling or electrical power connections are

required.

• Ease of Management

System management tools like the IBM Director permit hundreds of

blade servers to be maintained remotely through use of a single graphi-

cal console. This tool provides a common management view across

multiple servers in a chassis and enables a smaller IT staff to manage

the same number of servers.

This chapter discusses the key advantages of IBM BladeCenter and Mara-

thon Technologies FTvirtual Server and how they combine to create a truly

fault-tolerant environment for mission critical Windows applications.

Introduction

2 Marathon Technologies Corporation

• Reduced Floor Space Usage in the Data Center

Modular design reduces cost through more efficient use of valuable floor

space. The increased density can significantly reduce the space require-

ments in a data center.

• Reduced Cost of Power and Cooling

Blades servers integrate resources and share key components. Since

blades in a chassis share common power supplies, power is distributed

more efficiently and less heat is generated for a given amount of pro-

cessing power.

• Increased Reliability and Availability

Since the BladeCenter may be configured with redundant hot-swap

power supplies and built-in network switches, it effectively eliminates

several key single points of failure and provides greater system availabil-

ity than conventional rack-mount servers. The BladeCenter also

reduces down-time due to server failure by making replacement of a

failed server easy.

Mission-Critical Blades: The Need For Fault Tolerance

As enterprises move more compute load to blade servers, blades are

becoming increasingly mission-critical. Because downtime has significant

associated costs - lost sales, decreased customer satisfaction, lost produc-

tivity - the need for a simple, affordable way to keep blades running continu-

ously is becoming urgent. Four trends are converging to further increase

the need for continuously available blades:

• Improved server density and server consolidation increases the

potential risk to business operations in the event of downtime by

“putting all your eggs in one basket”

• Increasingly stringent regulations require data retention and avail-

ability

• More threats to security and physical systems

• Increasing complexity of enterprise infrastructure, and impact of

system downtime

Marathon Technologies Corporation 3

Marathon

FTvirtual Server

- Fault-Tolerance Through Software

To address the need for continuous availability of mission-critical applica-

tions, Marathon Technologies has designed its FTvirtual Server software to

work with blade server configurations as well as traditional servers.

Marathon software harnesses the redundancy provided by two BladeCenter

servers to create a true, fault- tolerant environment for Windows applica-

tions.This is accomplished by loading the Marathon software on any two

blade servers and interconnecting them via the BladeCenter’s integrated

chassis switching matrix. The Marathon software synchronizes the two

servers and creates a virtual application environment that runs on both

servers simultaneously. If either server in the connected pair fails, the appli-

cation environment continues to function uninterrupted, using the process-

ing power of the other. Unlike typical clustering technologies which require

seconds or even minutes to “fail-over” application processing and may

incure data loss, there is no failover with Marathon software, so there is no

downtime.

The result is a truely fault-tolerant Windows environment for BladeCenter

configurations. Enterprises get all the cost savings and operational efficien-

cies of the BladeCenter while protecting their business-critical Windows

applications and data, even in the event of a blade failure.

Conclusion

Blade servers are helping companies save money and increase efficiency

and flexibility in their data centers. However, without adequate fault protec-

tion, these benefits are soon lost in the event of downtime. Marathon’s

FTvirtual Server software delivers a simple, affordable way to protect impor-

tant applications and data running on IBM eServer BladeCenter configura-

tions.

Introduction

4 Marathon Technologies Corporation

Marathon Technologies Corporation 5

CHAPTER 2 Planning and Preparation

Planning the Installation

Before starting the Endurance software installation you should consider

several major configuration related issues, which will effect the overall oper-

ation and capability of your FTvirtual Servers.

FTvirtual Server Boot Disk Options

The Endurance software allows the FTvirtual Server boot disk to be

installed on either a separate physical disk or as a Virtual disk. If your blade

configuration is limited to a single on-board physical disk you will need to

use a Virtual boot disk for the FTvirtual Server. A virtual boot disk allows

you to share a single physical disk as both the CoServer and the FTvirtual

Server Windows boot disk. Disk space is allocated to a file on the CoServer

disk. The content of the file is then formatted, partitioned, and used as the

FTvirtual Server boot disk.

This chapter describes BladeCenter features and options, key design con-

cepts, and basic configuration guidelines you should be aware of before

beginning to install and setup a BladeCenter FTvirtual Server.

Planning and Preparation

6 Marathon Technologies Corporation

Network Environment

The optimal FTvirtual Server configuration uses 4 network adapters per

blade to support CoServer communications and client access links critical

to applications. These links provide the mechanisms and transport for redi-

rected network I/O, FTvirtual Server communications and fault manage-

ment activities.

When using the optimal network configuration, two of the adapters in each

blade will support CoServer Links (CSLink) 1 and 2, which are primarily

used for disk mirroring and memory synchonization operations. A third

adapter in each blade is used for CoServer out-of-band remote administra-

tion and SNMP management activities. The fourth serves as a redirected

network link permitting the FTvirtual Server to satisfy client and application

I/O requests.

CoServer and Switchbay Network Connections

A sample BladeCenter network map depicting the connections for two

FTvirtual Server configurations (FTv1 and FTv3) is shown in Figure 1. This

configuration demonstrates the optimal BladeCenter FTvirtual Server con-

figuration, maximizing server fault-tolerance and network availability.

It should be mentioned that although each switchbay is internally intercon-

nected with each slot of the BladeCenter chassis, these additional connec-

tions have been left out of the diagram for the sake of simplicity.

Note that in this 4 NIC configuration switchbays 1 and 2 provide dedicated

CSLink 1 and CSLink 2 switching capability for each of the FTv CoServers.

These connections are made internally to the BladeServer chassis and

none of the external ports available on these two switches are used for

external connections.

Switchbays 3 and 4 are configured for FTvirtual Server Redirected and

Management use. The four external ports available on these switches are

used to connect the FTvirtual Server/s to the public network.

Marathon Technologies Corporation 7

FIGURE 1.

FTv1 CoServer 1

PCI 1:0:0 NIC

Switch Bay 1

CSLink 1 connections only

No external connections

PCI 1:0:1 NIC

PCI 2:2:1 NIC

PCI 2:2:0 NIC

Switch Bay 2

CSLink 2 connections only

No external connections

Switch Bay 3

Redirected for CoServer 1

Management for CoServer 2

Switch Bay 4

Redirected for CoServer 2

Management for CoServer 1

FTv1 CoServer 2

PCI 1:0:0 NIC

PCI 1:0:1 NIC

PCI 2:2:1 NIC

PCI 2:2:0 NIC

FTv3 CoServer 2

PCI 1:0:0 NIC

PCI 1:0:1 NIC

PCI 2:2:1 NIC

PCI 2:2:0 NIC

FTv3 CoServer 1

PCI 1:0:0 NIC

PCI 1:0:1 NIC

PCI 2:2:1 NIC

PCI 2:2:0 NIC

To

Network

To

Network

Blade Bays 1, 5, 9 are assumed to contain CoServer 1

Blade Bays 3, 7, 11 are assumed to contain CoServer 2

Blade Bay pairs 1 & 3, 5 & 7, 9 & 11 each make an Endurance system

FTv2 CoServer 1

FTv2 CoServer 2

Sample BladeCenter Network Adapter Switchbay Map

Planning and Preparation

8 Marathon Technologies Corporation

Network Adapter Configurations

Depending upon your specific switchbay and blade on-board device config-

uration, it is possible that fewer than 4 adapters will be available for use.

When planning a BladeCenter network configuration your primary concern

should be to maximize the availability of the redirected network links and

minimize utilization of external networks by the CoServer links.

To maximize the availability of the redirected links, different switches

should be used to connect the CoServers to the external network. To mini-

mize utilization of the external network by the CoServer links, both CoServ-

ers should use the same internal switch for a CSLink connection. Routing a

CSLink connection through the same switch will confine all associated traf-

fic to that switch. Several recommended network configurations using 4, 3,

and 2 network adapters are shown in the following tables.

TABLE 1. 4 NIC Configuration

Function CoServer 1 CoServer 2 Comment

CSLink 1 Switchbay 1 Switchbay 1 Internal Bandwidth

CSLink 2 Switchbay 2 Switchbay 2 Internal Bandwidth

Redirected Switchbay 3 Switchbay 4 Redundant External Connection

Manage Switchbay 4 Switchbay 3 Redundant External Connection

TABLE 2.

3 NIC Configuration

Function CoServer 1 CoServer 2 Comment

CSLink 1 Switchbay 1 Switchbay 1 Internal Bandwidth

Redirected Switchbay 2 Switchbay 3 Redundant External Connection

CSLink 2 Switchbay 3 Switchbay 2 Exposed network utilization

Requires network routed IP

addresss

TABLE 3.

3 NIC Alternate Configuration

Function CoServer 1 CoServer 2 Comment

CSLink 1 Switchbay 1 Switchbay 1 Internal Bandwidth

Redirected Switchbay 2 Switchbay 3 Redundant External Connection

Manage Switchbay 3 Switchbay 2 Redundant External Connection

Marathon Technologies Corporation 9

For More Information

For more information on setting-up network configurations, Virtual boot

disks and other preparation issues consult the following resources located

on your Marathon software distribution CD-ROM:

• Administrator’s Guide

• Upgrading Endurance Software

• Configuration and Installation Guide

TABLE 4. 2 NIC Configuration

Function CoServer 1 CoServer 2 Comment

CSLink 1 Switchbay 1 Switchbay 2 Exposed network utilization.

Requires network routed IP

address.

Redirected Switchbay 2 Switchbay 1 Redundant External Connection

Planning and Preparation

10 Marathon Technologies Corporation

Preparing to Install

BladeCenter Options

An IBM eServer BladeCenter

may be configured using a variety of storage

and networking options. For example, the BladeCenter chassis using HS20

blade servers offers the following configuration features:

• A rack-optimized 7U modular 14 slot chassis that can support a

total of 14 hot-swap BladeCenter HS20 blades.

• A CD-ROM and floppy shared by all blade bays.

• A maximum of two Management modules integrating remote man-

agement functions and a 14-port Keyboard/Video/Mouse switch.

• Up to 4 Gigabit Ethernet Switch modules. Each switch has four

external ports as well as 14 internal ports (one to each bay).

• HS20 hot-swappable blades supporting two XEON processors, 4-

port Gigabit Ethernet modules, on-board disks and/or a piggy-

backed SCSI drive Expansion Unit.

Marathon Technologies Corporation 11

FTvirtual Server and Blade Configuration

Each Endurance FTvirtual Server configuration is comprised of two blades.

Following installation of the Endurance software each will function as a

CoServer to create the FTvirtual Server environment.

Depending upon the specific configuration, a 14 slot BladeCenter chassis

can support a total of 7 Endurance FTvirtual Servers (2 slots per FTvirtual

Server), using single-slot blades configured with one or two on-board disks

and four network adapters. If each blade is configured with four network

adapters and a piggy-backed SCSI Expansion Unit option for increased

storage capacity, a total of 3 Endurance configurations (4 slots per FTvirtual

Server) may be supported.

It is important to note that the chassis slot position of a blade has no impact

on its function. After an Endurance system has been established, the

blades can be moved to any chassis slot and located in any order. Data

communications between Endurance configured blades is controlled by IP

addresses, which are unique to a blade and FTvirtual Server blade pair.

Identifying Network Components

To help simplify Endurance software installation it is suggested that you first

create a chart that maps blade configured network adapters to their corre-

sponding ethernet switchbay connection. Since this mapping may vary

across blade (HSxx) models, it is important that you identify these connec-

tions prior to installation. Later, during the network setup phase of the instal-

lation you will be able to correlate a CoServer assigned networking role to

its corresponding adapter and ethernet switchbay connection.

A specific network adapter must be identified by its unique PCI bus location

in the system in terms of:

“PCI bus b, device d, function f”

Switchbays may be identified from the back of the BladeCenter cabinet by

the number of the particular bay they reside in.

Planning and Preparation

12 Marathon Technologies Corporation

Mapping the Switchbays

After installation of the Windows operating system on a blade you can fill-in

the switchbay mapping table for your particular configuration using the fol-

lowing procedure.

Note: Do not perform PCI-to-Switchbay mappings when blades

within the chassis are operating within a production

environment.

1. On one of the CoServer blades right-click My Network Places to view

the Network Connections dialog.

2. From the back of the BladeCenter cabinet select a switchbay and unplug

it.

3. Return to the CoServer console and observe the Network Connections

dialog and note which connection experiences a status change.

4. Right-click on the connection that changed status to display the Local

Area Connection Properties.

5. Click the Configure button to display the controller properties. Note the

switchbay number of the switch you unpluged and record the corre

-

sponding PCI location information for that adapter in Table 4. Plug the

switchbay back into its slot and wait for the connection status to return to

normal.

6. Repeat this procedure for each configured ethernet switchbay until you

have identified all connections. Since these connections will hold for like

blade models this mapping will work for all other configured blades.

TABLE 5. Adapter PCI-to-Switchbay Mappings

Blade Model Switchbay 1 Switchbay 2 Switchbay 3 Switchbay 4

Blade HS20

8832 Chassis

1:0:0 (b:d:f) 1:0:1 (b:d:f) 2:2:1 (b:d:f)

2:2:0 (b:d:f)

Blade HS20

8843 Chassis

5:1:0 5:1:1 6:1:0 6:1:1

Blade HSXX

88nn Chassis

Marathon Technologies Corporation 13

CHAPTER 3 Installing the Endurance

Software

Major Installation Tasks

The major installation tasks are:

1. Install Windows on both CoServers.

2. Install Endurance software on CoServer 1.

3. Install Endurance software on CoServer 2.

4. Install Windows on and configure the FTvirtual Server

This chapter describes in detail how to install and configure the Endurance

software on each of the BladeCenter CoServers to create the FTvirtual

Server.

Installing the Endurance Software

14 Marathon Technologies Corporation

Windows Installation

Before you begin the Endurance installation, install Windows and set the

size of the event logs.

Installing Windows on the CoServers

On both CoServers:

Install the appropriate Windows software and Service Packs. Refer to the

Endurance Release Notes for information about hardware and software

requirements, including Windows Security Updates.

Note: If the Manage Your Server or Configure Your Server window

appears, click Don’t display this page at logon, and then

dismiss the window.

Event Log Recommendations

On both CoServers:

For best results in tracking system events, make sure that the Application

Log and System Log on both CoServers are set to at least 16384 KB.

From Computer Management, select Event Viewer. For each log:

Right click, and select Properties.

If necessary, change the Maximum log size to at least 16384 KB. Verify

that the Overwrite events as needed box is checked.

Page is loading ...

Marathon Computer FTvirtual IBM BladeCenter User manual

This manual is also suitable for

Marathon Computer FTvirtual IBM BladeCenter User manual

Other documents