Panasonic TY42TM4Z Operating instructions

Panasonic
Brand
Panasonic
Model
TY42TM4Z
Type
Operating instructions
Italiano
Français
Español
Svenska
Dansk
TY-42TM4D
English
TQBC7059
Deutsch
RGB (digital) Terminal Board
Replacement Instructions
Befor attempting to install this board, please read these
instructions completely.
RGB-Terminal-Board (digital)
Anleitung zum Austausch
Bitte lesen Sie vor der Installation des Boards diese
Anleitung vollständig durch.
Nederlands
RGB (digitale) aansluitingenkaart
Montagehandleiding
Lees de handleiding aandachtig door voordat u de
aansluitingenkaart aanbrengt.
Scheda terminali RGB (digitale)
Istruzioni per il rimontaggio
Si prega di leggere con cura le istruzioni seguenti, prima di
provare ad installare questa scheda terminali.
Carte de connexion RVB (numérique)
Instructions de remplacement
Avant d'installer cette carte, lisez attentivement ces instruc-
tions.
Tarjeta de terminales (digital) RGB
Instrucciones para el reemplazo
Antes de intentar instalar esta tarjeta, lea completamente
estas instrucciones.
RGB uttagsplatta (digital)
Bytesinstruktioner
Läs noga de medföljande anvisningarna innan denna platta
installeras.
RGB (digital) terminalkort
Instruktioner for udskiftning
Læs denne vejledning helt igennem, før installation af dette
kort forsøges udført.
Handle
Screws (x4)
Avoid riding on claws.
Slot
Terminal function label
(accessory)
1.
Removing the Terminal Board from the
display:
1. Remove the four screws that secure the Terminal
Board to the rear of the display.
2. Hold the Terminal Board by the side grips and
slowly pull it out in the direction of the arrow.
2.
Installing the RGB (digital) Terminal Board:
1. Insert the RGB (digital) Terminal Board into the slot
until it is firmly plugged into the card connector.
• Check to make sure that the Board does not ride
on the two lower claws.
2. Secure the Board to the display with the four
screws removed in step 1 above. Tighten the
screws in the order of through .
3.
Applying the terminal function label:
Peel off the backing sheet from the accessory
terminal function label and affix it over the existing
label.
• Make sure that the label is affixed with the correct
orientation.
Cover the work table with a soft, clean cloth and carefully place the display screen-panel down on the cloth.
Then follow the steps below.
• Before proceeding with the replacement steps, be sure to turn off the entire system including the
display, unplug all components from their outlets, and disconnect all the interconnect cables from
the display.
• When removing or installing the Board, exercise care not to scratch the display's rear panel surface
or labels.
Notes
Precautions:
• When removing or installing the Tuner Terminal Board, exercise care to avoid injury.
There may be some sharp-pointed solder joints on the rear side of the Board that could cause unexpected
injury.
• When installing the Board, note the following point:
Fully insert the Board into the slot horizontally until it is firmly plugged into the connector. Note that
incomplete insertion may damage the internal components.
Have the customer keep the removed Terminal Board for future servicing needs.
English
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Panasonic TY42TM4Z Operating instructions

Panasonic
Brand
Panasonic
Model
TY42TM4Z
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents