Panasonic TY42TM4Z Operating instructions

Brand: Panasonic

Model: TY42TM4Z

Type: Operating instructions

Panasonic TY42TM4Z

Below you will find brief product information for Panasonic TY42TM4Z. This device is a RCA Terminal Board that must only be installed in the TH-42PW4, TH-42PWD4 models. It allows to display AV input and component input signals using RCA input Terminals. The device should only be installed by a qualified service engineer that will insert it in the terminal slot at the rear of the Plasma Display. Before the installation make sure to turn off the power switch, pull out the plug and disconnect any plugs connected to the Plasma Display.

Panasonic TY42TM4Z

RCA Terminal Board Installation Manual

Installationsanleitung für das RCA-Terminal-Board

Manuel d'installation de la carte de connexion RCA

Manuale d’installazione della scheda di terminali RCA

Manual de instalación del tablero de terminales RCA

Installatiehandleiding voor de RCA aansluitingenkaart

Installationsvejledning for RCA terminalkort

Installationsmanual för RCA uttagsplatta

RCA Terminal Board

Model No.

TY-42TM4Z

Svenska Dansk

EnglishDeutschFrançais

ItalianoEspañol

Nederlands

TQBC0284

• Users should not attempt to install or remove this product.

• Only a qualified service engineer should perform installation.

• Install this Terminal Board in the specified products only.

This product is a RCA Terminal Board, and must only be installed in the TH-42PW4, TH-42PWD4

models.

This should only be installed in the specified Plasma Display.

Failure to observe this point may result in damage to the projector and may further cause the

installed product to malfunction.

• Do not touch the product directly.

Highly sensitive electronic components are fitted in high density.

Touching components or the board directly while installing may cause the product to

malfunction.(During installation, ensure static electricity is discharged to earth by suitable means.)

• Always pull out the power cables from the AC socket before commencing installation.

• Do not drop the product or allow any action that may cause damage to it.

• Do not place this product in water or allow it to become wet.

• Do not attempt to modify this product in any way.

WARNING :

/B Y/G

COMPONENT/RGB INAV IN

S VIDEOVIDEO

AUDIO

This Terminal Board is the following arrangement

RCA Terminal Board Installation manual

• After installing this product in the Plasma Display (TH-42PW4 series), AV input and component input signals can be

displayed using RCA input Terminals.

Please confirm the model number of your

Plasma Display

model number

R - STANDBY

G POWER ON

INPUT

–

VOL

R - STANDBY

G POWER ON

TH-42PW4

English

Affixing the Terminal name indication label

Terminal name

indication label

Rear of Plasma Display

Affixing location

After completing installation of the Terminal Board, affix the included Terminal name indication label to the Plasma

Display.

To affix the label:

Peel off the rear protective sheet of the Terminal name

indication label.

For Plasma Display models to which a label is already

affixed, position the Terminal name indication label on

top of that label.

For models to which a label is not yet attached, affix the

Terminal name indication label while aligning with the molded

label locating marks, as shown in the figure.

For some models of the Plasma

Display, a label is already affixed.

Install the Terminal Board in the terminal slot at the rear of the Plasma Display.

Before installation

• Turn the power switch off and pull out the plug.

• Disconnect any plugs connected to the Plasma Display.

Place the Plasma Display upside down on a soft sur-

face, such as a foam mat.

Secure using the 4 screws removed at step 2 above.

Tighten screws in the numbered order ( – ).

Remove the 4 screws securing the slot cover or a

currently installed terminal board and remove the

cover or terminal board.

Note : The 4 screws are required for reassembly so

should be retained.

Confirm that the Terminal Board is correctly orientated

then carefully and slowly insert into the slot.

Ensure that the Board is completely seated.

Foam mat or thick

soft cloth

Note : Retain the cover or terminal board that has been removed in a safe location for potential future use.

Terminal name

indication label

Terminal name

indication label

Install

English

Molded marks for label location

Molded marks

Page is loading ...

Matsushita Electric Industrial Co., Ltd.

Web site : http://www.panasonic.co.jp/global/

Printed in Japan

MBS0701S0(MS)

Panasonic TY42TM4Z Operating instructions

Brand: Panasonic

Model: TY42TM4Z

Type: Operating instructions

Panasonic TY42TM4Z

Download PDF

report

in other languages

italiano: Panasonic TY42TM4Z Istruzioni per l'uso
français: Panasonic TY42TM4Z Mode d'emploi
español: Panasonic TY42TM4Z Instrucciones de operación
Deutsch: Panasonic TY42TM4Z Bedienungsanleitung
Nederlands: Panasonic TY42TM4Z Handleiding
dansk: Panasonic TY42TM4Z Betjeningsvejledning
svenska: Panasonic TY42TM4Z Bruksanvisningar

Panasonic TY42TM4Z Operating instructions

Panasonic TY42TM4Z Operating instructions

in other languages

Related papers

Other documents