Cisco 7821 User manual

Category
IP phones
Type
User manual

This manual is also suitable for

Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified
Communications Manager 10.0 (SIP)
First Published: October 25, 2013
Last Modified: September 19, 2014
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are
encouraged to try to correct the interference by using one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version
of the UNIX operating system. All rights reserved. Copyright
©
1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
©
2014 Cisco Systems, Inc. All rights reserved.
CONTENTS
CHAPTER 1
Getting Started 1
Accessibility Features 1
Cisco IP Phone 7821 1
Phone Connections 1
Buttons and Hardware 3
Phone Screen 6
Cisco IP Phone 7841 6
Phone Connections 6
Buttons and Hardware 8
Phone Screen 11
Cisco IP Phone 7861 11
Phone Connections 11
Buttons and Hardware 13
Phone Screen 15
Power Requirements 16
Power Save and Power Save Plus 16
Power Save 16
Power Save Plus 16
Additional Information 17
CHAPTER 2
Phone Setup 19
Connect Footstand 19
Adjust the Handset Rest 19
CHAPTER 3
Basic Operations 21
Clean the Phone Display 21
Make Calls 22
Predial a Number 22
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
iii
Place a Call Using the Speakerphone 22
Place a Call Using a Headset 23
Release a Call and Start Another Call 23
Dial an International Number 23
Redial a Number 24
Answer Calls 24
Answer Call Using PickUp 24
Answer Call Using Group PickUp and Group PickUp Number 24
Answer Call Using Group PickUp and Phone Number 25
Answer a Call Using Other PickUp 25
Automatically Answer Calls 25
Respond to Call Waiting Notification 26
Manage Calls 27
Divert a Call 27
Forward All Calls 27
Transfer a Call to Another Number 28
Swap Between Calls 28
Mute Phone 29
Monitor and Record Calls 29
Hold Calls 29
Swap Between Active and Held Calls 29
Put a Call on Hold by Answering a New Call 29
Respond to a Hold Reversion Notification 30
Determine If A Shared Line Is On Hold 30
Remote Hold 30
Setup Call Back Notification 30
Call Park 31
Park a Call Using Assisted Directed Call Park 31
Park a Call Using Manual Directed Call Park 32
Manage Intercom Calls 32
Place a Dedicated Intercom Call 32
Place a Dialable Intercom Call 33
Receive Intercom Call 33
View Phone Information 33
Sign In To the Cisco Unified Communications Self Care Portal 34
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
iv
Contents
CHAPTER 4
Contacts 35
Corporate Directory 35
Dial Contact from Search 35
Search and Dial While on Call 36
Personal Directory 36
Add Personal Directory Entry 37
Edit Personal Directory Entry 37
Delete Personal Directory Entry 37
Sign In and Out of Personal Directory 38
Dial Number from Personal Directory 38
Search for Entry in Personal Directory 38
Fast-Dial Codes with Personal Directory 39
Assign Fast-Dial Code to Personal Directory Entry 39
Place Call Using Fast-Dial Code 39
Delete Fast-Dial Code 40
Cisco WebDialer 40
Use Cisco WebDialer with Another Online Corporate Directory 40
Change Cisco WebDialer Preferences 40
Sign Out of Cisco WebDialer 41
CHAPTER 5
Call History 43
Call History Overview 43
View Call History 44
View Call Record Details 44
Filter Call History 44
Dial From Call History 45
Edit Phone Number 45
Clear Call History 46
Delete Call Record 46
CHAPTER 6
Voicemail 47
Voicemail Overview 47
Check for Voice Messages 47
Access Voicemail 48
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
v
Contents
Listen to Voice Messages 48
CHAPTER 7
Calling Features 49
Conference 49
Add Third Party to Conference 50
Combine Calls to Create Conference 50
Swap Between Calls Before Completing a Conference 50
View Conference Participants 51
Remove Conference Participant 51
Meet Me Conference 51
Host a Meet Me Conference 51
Join a Meet Me Conference 52
Speed Dial 52
Pause in Speed Dial 52
Place Call Using Speed-Dial Codes 53
Multilevel Precedence and Preemption 54
Make Priority Call with Login Required 55
Make Priority Call Without Login 55
Do Not Disturb 56
Turn DND On and Off 56
Line Status 56
Malicious Call Identification 57
Trace Suspicious Call 57
Cisco Extension Mobility 57
Enable Extension Mobility 58
Mobile Connect 58
Enable Mobile Connect 59
Turn Mobile Connect On or Off for All Remote Destinations from a Desk Phone 59
Switch a Desk Phone Call to a Mobile Phone 59
Switch a Mobile Call to the Desk Phone 60
Hand Off a Call from a Mobile Phone to the Desk Phone 60
Hunt Groups 60
Sign In and Out of a Hunt Group 60
Display Queue Statistics 61
cBarge 61
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
vi
Contents
Join Conference on Shared Line 61
Extension Mobility 61
Enable Extension Mobility 62
CHAPTER 8
Advanced Operations 63
Call Functions 63
Agent Greeting 63
Answer 63
Client Matter Code 64
Forced Authorization Code 64
Secure and Nonsecure Indication Tones 64
Shared Lines 65
Feature Buttons and Softkeys 65
Survivable Remote Site Telephony Overview 67
CHAPTER 9
Preferences 71
Adjust Brightness 71
Adjust Headset Sidetone 71
Change Ringtone 72
Line Settings 72
Phone Services 73
CHAPTER 10
Frequently Asked Questions 75
Frequently Asked Questions 75
CHAPTER 11
Troubleshooting 77
Conference Button and Softkey Unresponsive 77
Meet Me Conference Busy Tone 77
Cannot Sign In to Personal Directory 78
No Caller ID on Remote Hold 78
Cannot Access Self Care Portal 78
Security Error Message 79
CHAPTER 12
Product Safety and Security 81
Safety and Performance Information 81
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
vii
Contents
Power Outage 81
External Devices 81
Bluetooth Wireless Headset Performance 82
Power Information 82
FCC Compliance Statements 82
FCC Part 15.21 Statement 82
FCC RF Radiation Exposure Statement 82
FCC Receivers and Class B Digital Statement 83
Cisco Product Security Overview 83
CHAPTER 13
Warranty 85
Cisco One-Year Limited Hardware Warranty Terms 85
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
viii
Contents
CHAPTER 1
Getting Started
•
Accessibility Features, page 1
•
Cisco IP Phone 7821, page 1
•
Cisco IP Phone 7841, page 6
•
Cisco IP Phone 7861, page 11
•
Power Requirements, page 16
•
Power Save and Power Save Plus, page 16
•
Additional Information, page 17
Accessibility Features
The Cisco IP Phones 7821, 7841, and 7861 provide accessibility features for the vision impaired, the blind,
and the hearing and mobility impaired.
For detailed information about the accessibility features on these phones, see: http://www.cisco.com/en/US/
products/ps13220/products_feature_guides_list.html
You can also find more information about accessibility at this Cisco website:
http://www.cisco.com/web/about/responsibility/accessibility/index.html
Cisco IP Phone 7821
Phone Connections
For your phone to work, it must be connected to the corporate IP telephony network.
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
1
Access port (10/100 PC) connection.5DC adaptor port (DC48V) (optional).1
Auxiliary port (optional).6AC-to-DC power supply (optional).2
Handset connection.7AC power wall plug (optional).3
Analog headset connection (optional).8Network port (10/100 SW) connection. IEEE
802.3af power enabled.
4
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
2
Getting Started
Phone Connections
Buttons and Hardware
Indicates an incoming call (flashing red) or new voice message (steady
red).
Handset light strip1
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
3
Getting Started
Buttons and Hardware
Depending on how your system administrator sets up the phone,
programmable feature buttons (on each side of the phone screen) provide
access to:
•
Phone lines and intercom lines
•
Speed-dial numbers (speed-dial buttons, including the Line Status
speed-dial features)
•
Web-based services (for example, a Personal Address Book button)
•
Call features (for example, a Privacy button)
Buttons illuminate to indicate status:
•
Green, steady: Active call or two-way intercom call
•
Green, flashing: Held call
•
Amber, steady: Privacy in use, one-way intercom call, DND active,
or logged into Hunt Group
•
Amber, flashing: Incoming call or reverting call
•
Red, steady: Remote line in use (shared line or Line Status)
•
Red, flashing: Remote line on hold
Programmable feature
buttons
2
Shows information about your phone, such as directory number, active
call and line status, call duration, softkey options, speed dials, placed calls,
and phone menu listings.
Phone screen3
Depending on how your system administrator sets up the phone, enable
softkey options displayed on your phone screen.
Softkey buttons4
The Navigation and Select button allows you to scroll through menus,
highlight items and select the highlighted item.
Navigation and Select
button
5
Places an active call on hold and resumes the held call.
Hold/Resume button
6
Creates a conference call.Conference button7
Transfers a call.Transfer button8
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
4
Getting Started
Buttons and Hardware
Toggles the speakerphone on or off. When the speakerphone is on, the
button is lit.
Speakerphone button9
Toggles the headset on or off. When the headset is on, the button is lit.Headset button10
Toggles the microphone on or off. When the microphone is muted, the
button is lit.
Mute button11
Allows you to dial phone numbers, enter letters, and select menu items
(by entering the item number).
Keypad12
Controls the handset, headset, and speakerphone volume (off hook) and
the ringer volume (on hook).
Volume button
13
Opens or closes the Directories menu. Use the Contacts button to access
personal and corporate directories.
Contacts button14
Opens or closes the Applications menu. Use the Applications button to
access call history, user preferences, phone settings, accessories, subscribed
phone services, and phone model information.
Applications button15
Autodials your voice messaging system (varies by system).Messages button16
Phone handset.Handset17
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
5
Getting Started
Buttons and Hardware
Phone Screen
Displays date, time, and directory number.Header1
Display softkeys for available features or actions.Softkey labels2
Cisco IP Phone 7841
Phone Connections
For your phone to work, it must be connected to the corporate IP telephony network.
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
6
Getting Started
Phone Screen
Access port (10/100/1000 PC) connection.5DC adaptor port (DC48V) (optional).1
Auxiliary port (optional).6AC-to-DC power supply (optional).2
Handset connection.7AC power wall plug (optional).3
Analog headset connection (optional).8Network port (10/100/1000 SW) connection.
IEEE 802.3af power enabled.
4
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
7
Getting Started
Phone Connections
Buttons and Hardware
Indicates an incoming call (flashing red) or new voice message (steady
red).
Handset light strip1
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
8
Getting Started
Buttons and Hardware
Depending on how your system administrator sets up the phone,
programmable feature buttons (on each side of the phone screen) provide
access to:
•
Phone lines and intercom lines
•
Speed-dial numbers (speed-dial buttons, including the Line Status
speed-dial features)
•
Web-based services (for example, a Personal Address Book button)
•
Call features (for example, a Privacy button)
Buttons illuminate to indicate status:
•
Green, steady: Active call or two-way intercom call
•
Green, flashing: Held call
•
Amber, steady: Privacy in use, one-way intercom call, DND active,
or logged into Hunt Group
•
Amber, flashing: Incoming call or reverting call
•
Red, steady: Remote line in use (shared line or Line Status)
•
Red, flashing: Remote line on hold
Programmable feature
buttons
2
Shows information about your phone, such as directory number, active
call and line status, call duration, softkey options, speed dials, placed calls,
and phone menu listings.
Phone screen3
Depending on how your system administrator sets up the phone, enable
softkey options displayed on your phone screen.
Softkey buttons4
The Navigation and Select button allows you to scroll through menus,
highlight items and select the highlighted item.
Navigation and Select
button
5
Places an active call on hold and resumes the held call.
Hold/Resume button
6
Creates a conference call.Conference button7
Transfers a call.Transfer button8
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
9
Getting Started
Buttons and Hardware
Toggles the speakerphone on or off. When the speakerphone is on, the
button is lit.
Speakerphone button9
Toggles the headset on or off. When the headset is on, the button is lit.Headset button10
Toggles the microphone on or off. When the microphone is muted, the
button is lit.
Mute button11
Allows you to dial phone numbers, enter letters, and select menu items
(by entering the item number).
Keypad12
Controls the handset, headset, and speakerphone volume (off hook) and
the ringer volume (on hook).
Volume button
13
Opens or closes the Directories menu. Use the Contacts button to access
personal and corporate directories.
Contacts button14
Opens or closes the Applications menu. Use the Applications button to
access call history, user preferences, phone settings, and phone model
information.
Applications button15
Autodials your voice messaging system (varies by system).Messages button16
Phone handset.Handset17
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
10
Getting Started
Buttons and Hardware
Phone Screen
Displays date, time, and directory number.Header1
Displays text label and icon for phone or intercom
line, speed-dial numbers, or services, depending
on your configuration.
Line text label with icon2
Displays line label and call details for the primary
line, and other phone information such as placed
calls, speed dials, and phone menu listings.
Primary line details and other phone information3
Displays line label and call details for the secondary
line, and other phone information such as placed
calls, speed dials, and phone menu listings.
Secondary line details and other phone
information
4
Display softkeys for available features or actions.Softkey labels5
Cisco IP Phone 7861
Phone Connections
For your phone to work, it must be connected to the corporate IP telephony network.
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
11
Getting Started
Phone Screen
Access port (10/100 PC) connection.5DC adaptor port (DC48V).1
Auxiliary port.6AC-to-DC power supply (optional).2
Handset connection.7AC power wall plug (optional).3
Analog headset connection (optional).8Network port (10/100 SW) connection. IEEE
802.3af power enabled.
4
Cisco IP Phone 7821, 7841, and 7861 User Guide for Cisco Unified Communications Manager 10.0 (SIP)
12
Getting Started
Phone Connections
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94

Cisco 7821 User manual

Category
IP phones
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI