Datalogic WebSentinel™ PLUS Installation guide

Brand: Datalogic

Model: WebSentinel™ PLUS

Type: Installation guide

Datalogic WebSentinel™ PLUS is a server designed to work with the WebSentinel PLUS scan point monitoring system. It comes preloaded with software that allows it to connect to Datalogic scanning and dimensioning systems. The server has multiple ports for connecting to a static sorting/device network, a host network, a monitor, a mouse, and a keyboard. It also has USB 2.0 & 3.0 ports for connecting additional devices. The WebSentinel™ PLUS server can be configured to connect to a facility's Host network. It also allows for the creation of multiple user accounts with different levels of access.

WebSentinel™ PLUS Server

Installation Manual

The WebSentinel PLUS Server is recommended by Datalogic for use with

WebSentinel PLUS scan point monitoring system. The WebSentinel PLUS

server comes with the software preloaded and ready to connect to

Datalogic scanning and dimensioning systems. This document provides

information for a successful mechanical installation. For complete

information on WebSentinel PLUS, see the WebSentinel PLUS User’s

Manual.

UNPACKING INSTRUCTIONS

Carefully unpack the server from its box, and retain the box and packing

material in case the server ever needs to be shipped back to Datalogic.

Make sure the box has the following contents:

 WebSentinel PLUS Server PC with attached mounting brackets/

flanges

 Power Supply

 Power Cable

 Mounting brackets (already attached)

GENERAL MOUNTING GUIDELINES

It is important that you follow these general precautions when installing,

setting up, operating, maintaining, troubleshooting, or replacing any

Datalogic products, parts or related equipment.

As you plan and install your WebSentinel PLUS Server, be sure to keep the

following guidelines in mind:

 Determine the proper orientation and position the server. Mount

the server so connectors are accessible.

 Leave adequate clearances (approximately 300 mm [12 inches])

for wiring around the server for cabling.

 Route wires carefully to reduce or minimize electrical noise.

When power and communication wiring must cross, make their

intersection perpendicular.

 Proper grounding limits the effects of noise due to Electro-

magnetic Interference (EMI). Make sure the mounting structure

and power access is properly grounded.

Figure 1: Mounting to Structure

MOUNTING DIMENSIONS

Figure 2: Mounting Dimensions

DATALOGIC WEBSENTINEL PLUS SERVER CONNECTIONS

Figure 3: Server Connections

1. Power – Power supply connection

2. Digital Video – Monitor connections (optional, see Digital to Analog

converter below)

3. LAN A – Connection to HOST Network

4. LAN B – Connection to Device Network

5. USB 2.0 & 3.0 – Mouse and Keyboard connection (optional, see

section 2.6 Accessories)

6. Power Switch

FIRST TIME STARTUP AND NETWORK CONFIGURATION

After the Datalogic server has been mounted, attach the power, monitor,

LAN 2 device network (and LAN 1 Host if used), keyboard, and mouse

cables as shown in section 2.5.1. The Datalogic WebSentinel PLUS server

uses a Linux operating system, which must be configured for your facility’s

static sorting/device network. If desired, the server can also configure to

connect to your facility’s Host network.

Use the following procedure to configure the network adapter settings.

1. Press the power switch to turn on the server. The Log In screen

appears.

2. Select remotemonitor from the drop-down list.

3. Enter the default password, asiroot, and click Log In. The Linux

desktop is displayed.

4. Click the start icon in the upper left corner of the desktop. A Linux

menu appears.

5. Select Settings from the right side of the menu box, and then select

Network Connections from the list on the left. The Network

Connections box opens.

6. Click Add. The Editing box opens.

7. Select the Ipv4 Settings tab.

8. Select Manual from the Method drop-down list.

IMPORTANT: The IP addresses entered must be

a static IP assignment. DO NOT USE DHCP

ADDRESS ASSIGNMENT for the sorting/device

network.

9. Click Add, and enter the Address (IP address), Netmask, and

Gateway in the fields provided. Contact the facility IT administrator for

the correct connection information.

10. Click Save.

11. If desired, add another connection for the facility Host network.

Mount the server to the

structure extrusion with

threaded screws

(920000080).

Mounin

Mountin

brackets

INITIAL ADMINISTRATOR LOGIN AND LICENSING

To Gain Access to WebSentinel PLUS:

1. Click the Firefox Web Browser icon on the desktop to open the

browser.

2. Enter the IP Address of the server (created in step 9 above) in the

browser address bar to access the WebSentinel PLUS Login window.

3. If the IP Address (URL) for the server does not match the default in the

WebSentinel PLUS software, an Access Denied window appears.

4. Click on the Server IP Address Config link. The Server IP Address

Config window opens.

5. Under IPAddress.properties, enter the server IP Address in the New

text field, and click Update IPAddress.properties.

6. Under Sites IP Address, select your site from the Update Site IP

Address drop-down list, enter the server IP Address in the text field,

and click Update IP Address in DB.

NOTE: The Global Master Database IP can be set

as localhost if the server is not in linked or Enterprise

mode. If it is, then that field must be set to the IP

Address of the WebSentinel PLUS server that serves

as the Master.

7. Click Reboot Server.

8. After the server reboots, click the Firefox Web Browser icon on the

desktop to open the browser.

9. Again enter the IP Address of the server in the browser address bar.

The WebSentinel PLUS Login window opens.

10. The system administrator can log into WebSentinel PLUS using the

default User ID Admin and Password Admin.

Upon initial log in, the License Management window will appear.

11. Obtain a License Key by sending an email to

[email protected], and include the following

information:

 Name of the company or reference person to which the product

will be licensed.

 Product Key displayed on the License Management window.

 Product serial number found on the software package cover.

You will then receive a email reply with the License Key.

12. When you receive the email with the new License Key, copy the key

and paste it in the License Key field of the License Management

window.

13. Click Update License Key.

It is recommended that the system administrator immediately change

the Administrative password and set up system users (see the

WebSentinel PLUS User’s Manual).

System users can then obtain a User ID and Password from the system

administrator.

WEBSENTINEL PLUS SERVER ACCESSORIES

There are a few accessories that can be added to the Datalogic

WebSentinel PLUS server, including a monitor, keyboard/mouse, and

cabling.

ACCESSORY LIST PART NUMBER

KIT, MONITOR/KEYBRD/BRKT/USB HUB 93ACC0126

CBL,EXT,10FT,USB MOUSE/KEYBOARD 93ACC0108

ENC-3610 ENCLOSURE DIM CONTROLLER 93ACC0115

CABLE,NETWORK,2M,CAT6,DOUBLE-

SHIELDED,BLUE,ROHS EU 1000068706

CABLE,NETWORK,5M,CAT6,DOUBLE-

SHIELDED,BLUE,ROHS EU 1000068369

CABLE,NETWORK,10M,CAT6,DOUBLE-

SHIELDED,BLUE,ROHS EU 1000068707

SUPPORT THROUGH THE WEBSITE

Datalogic provides several services as well as technical support through its

website. Log on to www.datalogic.com and click on the SUPPORT link

which gives you access to:

Downloads by selecting your product model from the dropdown list in the

Search by Product field for specific Data Sheets, Manuals, Software &

Utilities, and Drawings;

Repair Program for On-Line Return Material Authorizations (RMAs) plus

Repair Center contact information;

Customer Service containing details about Maintenance Agreements;

Technical Support through email or phone.

COMPLIANCE

CE COMPLIANCE

CE marking states the compliance of the product with essential

requirements listed in the applicable European directive. Since the

directives and applicable standards are subject to continuous updates, and

since Datalogic promptly adopts these updates, therefore the EU

declaration of conformity is a living document. The EU declaration of

conformity is available for competent authorities and customers through

Datalogic commercial reference contacts. Since April 20th, 2016 the main

European directives applicable to Datalogic products require inclusion of an

adequate analysis and assessment of the risk(s). This evaluation was

carried out in relation to the applicable points of the standards listed in the

Declaration of Conformity. Datalogic products are mainly designed for

integration purposes into more complex systems. For this reason it is under

the responsibility of the system integrator to do a new risk assessment

regarding the final installation.

WARNING: This is a Class A product. In a domestic environment

this product may cause radio interference in which case the user

may be required to take adequate measures.

FCC COMPLIANCE

Modifications or changes to this equipment without the expressed written

approval of Datalogic could void the authority to use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference which may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his/her

own expense.

EAC COMPLIANCE

Customs Union:

The CU Conformity certification has been achieved; this allows the Product

to bear the Eurasian mark of conformity.

LEGAL NOTICE

RESERVED. Without limiting the rights under copyright, no part of this

documentation may be reproduced, stored in or introduced into a retrieval

system, or transmitted in any form or by any means, or for any purpose,

without the express written permission of Datalogic S.p.A. and/or its

affiliates.

Datalogic and the Datalogic logo are registered trademarks of Datalogic

S.p.A. in many countries, including the U.S.A. and the E.U.

WebSetntinel PLUS is a trademark of Datalogic S.p.A. and/or its affiliates.

All other trademarks and brands are property of their respective owners.

Datalogic shall not be liable for technical or editorial errors or omissions

contained herein, nor for incidental or consequential damages resulting

from the use of this material.

821004272 Rev. B

Datalogic WebSentinel™ PLUS Installation guide

Datalogic WebSentinel™ PLUS Installation guide

Datalogic WebSentinel™ PLUS Installation guide

Related papers