FMI VFF KD 100 Operating instructions

Type
Operating instructions

FMI VFF KD 100 is a mantel kit designed for use with FPVF33R series natural gas and propane fireplace systems and (R)UV32 and NL(R)UV32 series fireboxes. It is made of finished oak veneer and includes a batten mold strip, brass trim kit, trim kit hardware, and mounting blocks. The mantel is easy to assemble and install, and it comes with all the necessary hardware. It is also paintable, so you can customize it to match your décor.

Here are some of the features and possible use cases of the FMI VFF KD 100 mantel kit:

  • It can be used to add a touch of elegance to any room in your home, and it is perfect for use with fireplaces.

FMI VFF KD 100 is a mantel kit designed for use with FPVF33R series natural gas and propane fireplace systems and (R)UV32 and NL(R)UV32 series fireboxes. It is made of finished oak veneer and includes a batten mold strip, brass trim kit, trim kit hardware, and mounting blocks. The mantel is easy to assemble and install, and it comes with all the necessary hardware. It is also paintable, so you can customize it to match your décor.

Here are some of the features and possible use cases of the FMI VFF KD 100 mantel kit:

  • It can be used to add a touch of elegance to any room in your home, and it is perfect for use with fireplaces.
WARNING ICON G 001
WARNING: Carefully remove each mantel piece one at a time from
shipping carton. Do not try to lift all of the parts out of the box at once. This
may damage mantel pieces.
Firebox
Perimeter Brass
Trim included
with this
Mantel
Read entire instruction sheet before assembling or in-
stalling mantel kit.
This mantel is only approved for use with FPVF33R
series natural gas and propane fireplace systems and
(R)UV32 and NL(R)UV32 series fireboxes. Do not use
mantel with any other product. Several optional acces-
sories are available for this mantel kit. These accesso-
ries include the G3006FB Hearth. Contact dealer to pur-
chase optional accessories.
This mantel kit contains the following pieces:
Hardware 101472-01
Batten Mold Strip 103468-17
Brass Trim Kit 102753-01
Trim Kit Hardware 102865-01
Mounting Blocks 101477-09
The hardware package contains the following:
15 - 1
1
/4" wood screws
Colored finishing nails
Tools required
#2 Phillips screw driver Pencil
Flat head screw driver Drill
Measuring tape
If any of these pieces are missing or damaged, contact the dealer
where you purchased this kit. Call DESA International’s Parts
Department at 1-800-972-7879 for referral information.
Shown with Optional
Hearth Base and Trims
FM106FB Finished Oak Veneer
Cabinet Mantel
Assembly and Installation Instructions
2
106011
WARNING ICON G 001
WARNING: Use care when finishing an unfinished mantel. Do not finish mantel pieces near running heater
or open flame. Vapors from most finishing products are highly flammable. Follow manufacturer’s guidelines
when using finishing products.
FM106FB Mantel Kit
Assembly and Installation Instructions
IMPORTANT:
If you are painting an unfinished mantel, apply an oil base undercoat to the mantel before painting. This will seal the wood.
After undercoat dries completely, lightly sand and apply an oil base top coat. If you do not apply an oil base undercoat and topcoat, the
wood grain will bleed through the paint.
Figure 2 - Attaching Mantel Right Front to Mantel Right Side
Right Side
Right
Front
Male
Twistlock
Fastener
Female
Twistlock
Fastener
Screw
WARNING ICON G 001
WARNING: Carefully remove each mantel piece
one at a time from shipping carton. Do not try to lift
all of the parts out of the box at once. This may
damage mantel pieces.
UNPACKING MANTEL
1. Carefully remove packaging materials, header, right front, and
left front one at a time from shipping carton.
2. Remove 2 screws attaching left side to right side (see Figure
1). Remove one side from shipping carton. Discard screws.
Remove 2 screws attaching other side to top. Discard screws.
Remove other side from shipping carton.
3. Remove top from shipping carton.
Figure 1 - Removing Mantel Pieces from Shipping Carton
Header
Left Front
Right Front
Side
Side
Screw
Screw
Top
Shipping Carton
ASSEMBLING MANTEL
1. If you must install mantel flush with wall, baseboard will pre-
vent proper installation of mantel. Either alter baseboard to fit
mantel or remove baseboard.
2. Insert male twistlock fasteners (located on right side) in fe-
male twistlock fasteners (located on right front) (see Figure
2). Tighten screws of twistlock fasteners one-half turn with
flat head screwdriver. Repeat for left side. This will lock the
fasteners together.
3. Rest header on face boards of right and left sides (see Figure
3). Push sides together to eliminate gaps with header. Push
down on header to ensure a tight fit (see Figure 4). Attach
header to right side with two 1
1
/4" screws. Repeat for other
side (see Figure 4).
4. Place one mounting block on back of one of the side face boards
and the front panel. Attach mounting block to front panel and
to side face board with two 1
1
/4" screws (see Figure 4). Re-
peat for other side.
5. Place top on assembly (see Figure 5).
Make sure molding on top fits properly over front and side
panels. Back edge of top should be flush with back edge of
sides. From backside of mantel, locate predrilled holes near
top of left side. Attach with three 1
1
/4" wood screws (see Fig-
ure 6). Repeat above steps to attach top to right side. Locate
predrilled hole near the center of the header. Attach the header
to the top using one 1
1
/4" wood screw.
Note:
If using optional hearth base with mantel, move hearth base
to installation location. If using mantel without optional hearth
base, move mantel to installation location.
3
106011
Figure 6 - Attaching Top
Figure 3 - Installing Header
Header
Left
Side
Right
Side
Figure 4 - Attaching Header
Header
Side Face
Boards
Top
Header
Figure 5 - Placing Mantel Top on Mantel Assembly
Header
Top
1
1
/4" Wood Screws
Side
Side
Face Boards
1
1
/4"
Wood
Screws
Mounting
Block
Side
1
1
/4"
Wood
Screws
Continued
WARNING ICON G 001
WARNING: A qualified service person must in-
stall gas piping to heater. Follow all local codes.
6. Place mantel in desired location. Place firebox in front open-
ing of mantel. To make firebox fit through mantel opening,
bend back or remove nailing flanges on sides of the firebox.
Make sure all pieces fit properly. Remove mantel. Follow in-
structions included with heater or base to attach to floor.
7. Mark floor or wall for gas line entrance. Make sure there is
enough clearance between heater and mantel for gas line.
IMPORTANT:
Make sure there are no electrical lines where
gas piping will go through floor or wall.
Colored Finishing Nails
Batten Molding
Figure 7 - Attaching Batten Molding to Header
Header
8. From gas meter or propane tank, run hard piping to manual
shutoff valve. You must install the manual shutoff valve within
reach from heater. Install an approved flex hose (if allowed by
local or state codes) for natural or propane gas to run from the
manual shutoff valve to heater.
9. Connect heater to gas line according to instructions in heater
owner’s manual. Check all connections for leaks from heater
to gas meter or propane tank.
WARNING ICON G 001
WARNING: Never use an open flame to check for
a leak. Apply a mixture of liquid soap and water to all
joints. Bubbles forming show a leak. Correct all leaks
at once.
10. To attach batten molding to mantel assembly, measure up 3
3
/16"
from bottom of mantel front panel (see Figure 7).
Note:
If
using optional laminate trim, install trim before attaching bat-
ten molding to mantel assembly. Place bottom of batten mold-
ing at this measurement. It may be necessary to lightly sand
ends of molding to ensure proper fit. Use masking tape to hold
molding in place. Use level to ensure proper positioning. Drill
a pilot hole through molding and mantel with a small drill bit.
Attach to mantel front panel with colored finishing nails.
IMPORTANT:
Keep nails centered on molding to prevent split-
ting. Fill nail holes with wood putty.
WARNING ICON G 001
CAUTION: Nails will bend if pilot hole is not drilled.
11. After firebox is secured, replace mantel. Assemble and install
brass trim.
Figure 8 - Assembling Brass Trim
Side Brass
Trim
Mitered Edge
Shim
Adjusting
Plate
Set Screws
Top Brass Trim
Slot
Slot
Assembled
Brass Trim
Trim Hanging
Shoulder Screws
Hanging
Notches
on Trim
ASSEMBLING AND INSTALLING BRASS TRIM
1. Remove packaging from three pieces of brass trim.
2. Locate 2 adjusting plates with set screws and 2 shims in the
hardware packet.
3. Align shim under adjusting plate as shown in Figure 8.
4. Slide one end of adjusting plate/shim in slot on mitered edge
of top brass trim (see Figure 8).
5. Slide other end of adjusting plate/shim in slot on mitered edge
of side brass trim (see Figure 8).
6. While firmly holding edges of brass trim together, tighten both
screws on the adjusting plate using a slotted screwdriver.
7. Repeat steps 1 through 6 for other side.
8. Locate seven hanging shoulder screws in hardware packet.
Tighten the seven hanging shoulder screws (#10-16x.50 long
with .12 shoulder) into holes on firebox sides. Place the as-
sembled trim onto firebox cabinet. Align hanging notches on
trim with hanging screws on side of firebox (see Figure 9). Tap
trim firmly into place with palm of hand engaging hanging
notches around shoulder screws. Start at one end of the trim
and work around firebox until all notches are fully engaged.
Shoulder
Screw
Hanging
Notches
on Trim
Figure 9 - Assembling Brass Trim
106011-01
Rev. A
06/99
2701 South Harbor Blvd.
Santa Ana, CA 92704
901266 01
NOT A UPC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

FMI VFF KD 100 Operating instructions

Type
Operating instructions

FMI VFF KD 100 is a mantel kit designed for use with FPVF33R series natural gas and propane fireplace systems and (R)UV32 and NL(R)UV32 series fireboxes. It is made of finished oak veneer and includes a batten mold strip, brass trim kit, trim kit hardware, and mounting blocks. The mantel is easy to assemble and install, and it comes with all the necessary hardware. It is also paintable, so you can customize it to match your décor.

Here are some of the features and possible use cases of the FMI VFF KD 100 mantel kit:

  • It can be used to add a touch of elegance to any room in your home, and it is perfect for use with fireplaces.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI