Humandata ACM-023-115C8 User manual

Brand
Humandata
Model
ACM-023-115C8
Type
User manual

This manual is also suitable for

HuMANDATA LTD.
Cyclone IV E FPGA Board
ACM-023 Series
User’s Manual
Ver. 1.3
Table of Contents
Revision History ................................................................................................. 1
Introduction ........................................................................................................ 1
1. Unused Pins [IMPORTANT] ................................................................................. 2
2. Specifications ......................................................................................................... 3
3. Overview ................................................................................................................ 4
3.1. Name of Parts .................................................................................................... 4
3.2. Block Diagram ................................................................................................... 5
3.3. Power Supply ..................................................................................................... 6
3.4. JTAG Connector (CN3) ...................................................................................... 6
3.5. Configuration Mode Swich (SW3) ..................................................................... 6
4. FPGA Configuration .............................................................................................. 7
5. Configuration Device Programming ...................................................................... 7
5.1. Generating jic file .............................................................................................. 7
5.2. Programming Configuration Device ................................................................. 7
6. Additional Documentation and User Support ....................................................... 8
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. In case item 2, above, HuMANDATA guarantee its products for a period of 60 days from the date of shipping.
4. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
5. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
6. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
7. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
8. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
9. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
10. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
11. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
12. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
13. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
14. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
ACM-023 Series v1.3
Revision History
Revision Date Description
v1.0 Dec. 1, 2010 Initial release
v1.1 Apr. 22, 2013 Correct: VREFB pin names in Unused Pins
v1.2 May. 31, 2013 Correct: Switch setting of configuration mode.
v1.3 Jun. 25, 2015 Correct: Typos
Introduction
Thank you for buying our product ACM-023.
This is an evaluation board equipped with an Altera Cyclone IV E, voltage
regulators, configuration reset circuit, oscillators and configuration device.
It can provide you with very convenient and easy-to-use development environment.
2
ACM-023 Series v1.3
1. Unused Pins [IMPORTANT]
Some unused I/O pins are connected to GND or VCCINT (1.2 V). Some VREFB pins
are connected to each other.
Smaller FPGAs use those pins as general-purpose I/Os, but larger FPGAs use those
pins as GND or VCC.
Therefore, these pins should not be used as output port.
GND VCCINT(1.2V) VREFB
E10 K7 G10 P17 P20 M5
F16 N17 G14 P7 W19 T3
G11 P6 G16 R14 N19 R5
G13 R18 G4 R15
G15 T10 G8 R6
G17 T14 H17 T11
G7 U13 J17 U15
G9 U19 J7 U16
H16 U7 K17 U17
J19 V6 N16 U8
J5 Y21 N7 V7
To configure the unused I/O pins using Quartus II follow the steps below:
1. Open “Assignments” and click “Device…”
2. Click “Device & Pin Options…” button
3. Open “Unused Pins” tab
4. Set Reserve all unused pins as “As input tri-stated”
3
ACM-023 Series v1.3
2. Specifications
Model Name ACM-023-55C8 ACM-023-75C8 ACM-023-115C8
FPGA EP4CE55F23C8N EP4CE75F23C8N EP4CE115F23C8N
Config. Device EPCS16SI8N
(16Mbit)
EPCS64SI16N
(ALTERA, 64Mbit)
MRAM MR2A16AYS35 (Everspin, 4Mbit)
User I/O 100
On-Board Clock 30, 50 [MHz]
User LED 2
Status LED 2 (Power, Done)
Power-On Reset 200 [ms] typ. (Configuration Reset Signal)
JTAG Connector DIL 10-pin socket, 2.54 [mm] pitch
Power Input DC 3.3 [V]
(Internal power is generated by an on-board regulator.)
Core Voltage 1.2 [V]
PCB 8 Layer FR-4 t1.6 [mm] Immersion gold
Dimensions 3.386" x 2.126" (86 x 54 [mm])
Weight 32 [g] typ.
User I/O Connectors 66-pin through-hole
dia. 0.9 (typ.) [mm], 100[mil]/2.54 [mm] pitch
Accessories DIL 10 long pin headers x 1
DIL 80-pin headers (Cuttable) x 2
RoHS Compliance YES
* There may be cases that these parts and specifications are changed.
4
ACM-023 Series v1.3
3. Overview
3.1. Name of Parts
Component Side
Solder Side
User I/Os CNB
User LED
User Swich
Serial I/F (TTL)
User I/Os CNA
Power LED
JTAG
Config. Swich
Config. Device
Oscillator
50 MHz
MRAM
Oscillator
30 MHz
DONE LED
5
ACM-023 Series v1.3
3.2. Block Diagram
Cyclone-IV E
EP4CE 55/75/115
F23C8N
Power Circuit
2.5V, 1.2 V
Power LED
(3.3 V)
MRAM
(4 Mbit)
Config. Device
EPCS 16/64
User LED
User I/Os CNB
VIO(B) INPUT
User I/Os CNA
3.3 V INPUT E xt ernal CLK (option)
User Switch
.jic
Oscillator
50 MHz
30 MHz
Power-On Reset
Typ. 200ms
DONE LED
2
2
JTAG
JTAG
Buffer
50 GPIO
E xt ernal CLK (option)
50 GPIO
External CLK
MMCX (option)
P/N
6
ACM-023 Series v1.3
3.3. Power Supply
This board operates from single DC 3.3V power supply. Please apply power to CNA
and CNB with thick print pattern or cable. Please connect all ground pins.
The external power supply should be sufficient and stabilized.
The supply via CNB connector is used as CNB I/O banks power supply.
The supply via CNA connector is configured to 3.3V input.
For more details, please refer to circuit schematic.
3.4. JTAG Connector (CN3)
This connector is used to configure the FPGA and to access to configuration device
in system. Pin assignment is as follows.
Signal Name JTAG Pin Signal Name
TCK 1 2 GND
TDO 3 4 VCC
TMS 5 6 -
- 7 8 -
TDI 9 10 GND
3.5. Configuration Mode Swich (SW3)
Config. Switch (SW3) is used to set configuration mode of FPGA device.
To set the signal to zero : switch ON
1 2 3 4
Mode MSEL0 MSEL1 MSEL2 MSEL3 Function
AS OFF ON OFF OFF Config. Device Access
JTAG X X X X FPGA Access
X : Don’t Care
AS mode is used for programming configuration device using jic file, and for
configuring FPGA with configuration device at power-on sequence.
Generally, the other modes are not required.
For more details, please refer to FPGA data sheet.
7
ACM-023 Series v1.3
4. FPGA Configuration
To configure the FPGA via JTAG, select FPGA icon detected by [Auto Detect] and
assign a sof file.
If configuration is completed successfully, the DONE LED will light up.
5. Configuration Device Programming
To download an FPGA configuration data to the configuration device via JTAG, jic
(JTAG Indirect Configuration) file is required.
To generate a jic file using Quartus II, please refer to the following steps.
5.1. Generating jic file
Start Quartus II, and open [File] menu and click [Convert Programming Files]
and set items as shown below.
Programming File Type : JTAG Indirect Configuration File (.jic)
Configuration Device : EPCS16 or EPCS64 (set one device)
File name : any
1. Open [Flash Loader] and click [Add Device…], then select mounted [Device
name].
2. Open [SOF Data] and Click [Add File…], then select the sof file.
3. Click [Generate]
5.2. Programming Configuration Device
Please set configuration mode switch to AS mode.
Click [Add File…] and select the jic file, then check [Program/Configure] and
click [Start].
8
ACM-023 Series v1.3
6. Additional Documentation and User Support
The following documents and other supports are available at
http://www.hdl.co.jp/en/spc/ACM/acm-023/
Circuit Schematic
Pin List
Dimensional drawing
PCB drawing
Net List
… and more.
Cyclone IV E FPGA Board
ACM-023 Series
User’s Manual
Ver. 1.3 .............................................. Jun. 25, 2015
HuMANDATA LTD.
Address: 1-2-10-2F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: http://www2.hdl.co.jp/en/ (Global)
http://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Humandata ACM-023-115C8 User manual

Brand
Humandata
Model
ACM-023-115C8
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents