Behringer Tube Ultragain MIC100 Quick start guide

Quick Start Guide (Check Out behringer.com for FullManual)

TUBE ULTRAGAIN MIC100

Audiophile Vacuum Tube Preamplier with Limiter

2 TUBE ULTRAGAIN MIC100 3Quick Start Guide

Terminals marked with this

symbol carry electrical

current of su cient

magnitude to constitute risk of electric

shock. Use only high-quality professional

speaker cables with ¼" TS or twist-locking

plugs pre-installed. Allother installation

or modi cation should be performed only

by quali edpersonnel.

This symbol, wherever it

appears, alertsyou to the

presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be su cient

to constitute a risk ofshock.

This symbol, wherever it

appears, alertsyou to

important operating and

maintenance instructions in the

accompanying literature. Please read

themanual.

Caution

To reduce the risk of electric

shock, donot remove the

top cover (or the rear section). No user

serviceable parts inside. Refer servicing to

quali ed personnel.

Caution

To reduce the risk of  re or

electric shock, do not expose

this appliance to rain and moisture.

The apparatus shall not be exposed to

dripping or splashing liquids and no

objects  lled with liquids, suchas vases,

shall be placed on the apparatus.

Caution

These service instructions

are for use by quali ed

service personnel only. Toreduce the

risk of electric shock do not perform any

servicing other than that contained in the

operation instructions. Repairs have to be

performed by quali ed servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5.

Do not use this apparatus near water.

6. Clean only with dry cloth.

Important Safety

Instructions

7. Do not block any ventilation

openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources

such as radiators, heat registers, stoves,

or other apparatus (including ampli ers)

that produce heat.

9. Do not defeat the safety purpose

of the polarized or grounding-type plug.

Apolarized plug has two blades with one

wider than the other. A grounding-type

plug has two blades and a third grounding

prong. The wide blade or the third

prong are provided for your safety. Ifthe

provided plug does not  t into your outlet,

consult an electrician for replacement of

the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11. Use only attachments/accessories

speci ed by themanufacturer.

12. Use only with

the cart, stand, tripod,

bracket, or table speci ed

by the manufacturer,

orsold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during

lightning storms or when unused for long

periods of time.

14. Refer all servicing to quali ed

service personnel. Servicing is required

when the apparatus has been damaged

in any way, such as power supply cord or

plug is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain or

moisture, does not operate normally, or

has beendropped.

15. The apparatus shall be connected to

a MAINS socket outlet with a protective

earthing connection.

16. Where the MAINS plug or an

appliance coupler is used as the

disconnect device, the disconnect device

shall remain readily operable.

4 TUBE ULTRAGAIN MIC100 5Quick Start Guide

Las terminales marcadas con

este símbolo transportan

corriente eléctrica de

magnitud su ciente como para constituir

un riesgo de descarga eléctrica. Utilicesolo

cables de altavoz profesionales y de alta

calidad con conectores TS de 6,3 mm o de

bayoneta pre jados. Cualquier otra

instalación o modi cación debe ser

realizada únicamente por un técnico

cuali cado.

Este símbolo, siempre que

aparece, leadvierte de la

presencia de voltaje peligroso

sin aislar dentro de la caja; estevoltaje

puede ser su ciente para constituir un

riesgo dedescarga.

Este símbolo, siempre que

aparece, leadvierte sobre

instrucciones operativas y de

mantenimiento que aparecen en la

documentación adjunta. Por favor,

leaelmanual.

Atención

Para reducir el riesgo de

descarga eléctrica, no quite

la tapa (o la parte posterior). Nohay

piezas en el interior del equipo que

puedan ser reparadas por el usuario.

Sies necesario, póngase en contacto con

personalcuali cado.

Atención

Para reducir el riesgo de

incendio o descarga eléctrica,

no exponga este aparato a la lluvia,

humedad o alguna otra fuente que pueda

salpicar o derramar algún líquido sobre

el aparato. Nocoloque ningún tipo de

recipiente para líquidos sobre el aparato.

Atención

Las instrucciones de servicio

deben llevarlas a cabo

exclusivamente personal cuali cado.

Para evitar el riesgo de una descarga

eléctrica, no realice reparaciones que no

se encuentren descritas en el manual

de operaciones. Lasreparaciones deben

ser realizadas exclusivamente por

personalcuali cado.

1. Lea las instrucciones.

2. Conserve estas instrucciones.

3. Preste atención a todas

lasadvertencias.

TECHNICAL SPECIFICATIONS AND

APPEARANCES ARE SUBJECT TO

CHANGE WITHOUT NOTICE AND

ACCURACY IS NOT GUARANTEED.

BEHRINGER, KLARKTEKNIK, MIDAS,

BUGERA, AND TURBOSOUND

ARE PART OF THE MUSIC GROUP

MUSICGROUP.COM. ALL

TRADEMARKS ARE THE PROPERTY

OF THEIR RESPECTIVE OWNERS.

MUSICGROUP ACCEPTS NO LIABILITY

FOR ANY LOSS WHICH MAY BE

SUFFERED BY ANY PERSON WHO RELIES

EITHER WHOLLY OR IN PART UPON

ANY DESCRIPTION, PHOTOGRAPH

OR STATEMENT CONTAINED HEREIN.

COLORS AND SPECIFICATIONS MAY

VARY FROM ACTUAL PRODUCT.

MUSICGROUP PRODUCTS ARE

SOLD THROUGH AUTHORIZED

FULLFILLERS AND RESELLERS ONLY.

FULLFILLERSAND RESELLERS ARE

NOT AGENTS OF MUSICGROUP AND

HAVE ABSOLUTELY NO AUTHORITY

TO BIND MUSICGROUP BY ANY

EXPRESS OR IMPLIED UNDERTAKING

OR REPRESENTATION. THIS MANUAL

IS COPYRIGHTED. NO PART OF THIS

MANUAL MAY BE REPRODUCED OR

TRANSMITTED IN ANY FORM OR BY ANY

MEANS, ELECTRONIC OR MECHANICAL,

INCLUDING PHOTOCOPYING

AND RECORDING OF ANY KIND,

FORANY PURPOSE, WITHOUT THE

EXPRESS WRITTEN PERMISSION OF

MUSICGROUPIPLTD.

Trident Chambers, Wickhams Cay,

P.O. Box 146, Road Town, Tortola,

British Virgin Islands

For the applicable warranty terms

and conditions and additional

information regarding MUSICGroup’s

Limited Warranty, pleasesee

complete details online at

www.music-group.com/warranty.

Instrucciones de

seguridad

LEGAL DISCLAIMER

LIMITED WARRANTY

Page is loading ...

TUBE ULTRAGAIN MIC10020 21 Quick Start Guide

TUBE ULTRAGAIN MIC100 Controls

INPUT OUTPUT

(6) (7)(9) (10) (11) (13)

User interface of the MIC100

(12)(8)

(1) (2) (5)(3) (4)

Side panel of the MIC100

TUBE ULTRAGAIN MIC10022 23 Quick Start Guide

TUBE ULTRAGAIN MIC100 Controls

(1) Use the POWER SUPPLY CONNECTOR

to hook up the enclosed power supply

unit. Next to this connector you’ll nd

the strain relief clamp, whichprevents

accidental release of the power supply.

(2) This is the balanced XLR OUTPUT of

your MIC100. Use this connector to feed

the XLR input of your mixing console,

multitrack recorder or poweramp.

(3) The balanced ¼" TRS OUTPUT of your

MIC100 can also be connected to either

mixer, recording system or power amp.

(4) The balanced ¼" TRS INPUT of your

MIC100 can be used to connect your

electric guitar, for example. This input is

wired parallelly to the XLR input.

(5) Use the balanced XLR INPUT to connect

your microphone.

◊ In contrast to its outputs,

the MIC100’s inputs should never

be used simultaneously!

(6) The GAIN control allows applying

gain from +26 to +60 dB to the input

signal. This control should be set fully

counterclockwise when (dis)connecting

a sound source to the MIC100. Whenall

connections aremade, slowly start

raising gain.

(7) We recommend using the LED meter to

adjust gain. The LED chain displays the

output signal level in dB. Pleasemake

sure that the clip LED never lightsup

permanently. Itshould light up only at

peak signals, butnever allthe time.

(8) If your MIC100 is connected to the mains

via the enclosed power supply unit,

thePOWER LED lights up to indicate

that your MIC100 is running.

(9) The 20 dB PAD button reduces the input

sensitivity by 20 dB. Theappropriate

setting depends on the equipment

connected. No matter what your

application is, the clip LED warns you to

reduce the gain setting, so as to avoid

distortion.

(10) This +48 V switch activates

the phantom power supply for

the XLR input. Phantom power

supply is required for operating

condensermicrophones.

(11) With the PHASE REVERSE switch,

the input signal is reversed by 180°.

This function is available for both mic

and line signals. Use this function

in a multi-microphone setup if you

detect phase cancellations in specic

frequencybands.

(EN) Controls

(12) Use the LIMITER switch to limit the

signal and to prevent distortion.

(13) The OUTPUT control governs the

output level of the device within a

range from -∞ to +10 dB. If the control

is set fully counter-clockwise, there is

no output signal at all. The more the

control is set clockwise, the higher the

outputlevel.

Page is loading ...

32 TUBE ULTRAGAIN MIC100 33Quick Start Guide

Specications

Audio Inputs

XLR Input

Connector balanced/unbalanced

Type transformerless, DC-decoupledinput

Impedance approx. 2kΩ

Max. input level +7dBu / -20 dB with pad

¼" TRS Input

Connector balanced/unbalanced

Type transformerless, DC-decoupledinput

Impedance approx. 1MΩ

Max. input level

+16dBu / -20 dB with pad

Audio Outputs

Connectors

XLR connector + ¼" TRS jack

balanced/unbalanced

Type transformerless, DC-decoupledoutput

Impedance approx. 700Ω balanced / 350Ω unbalanced

Max. output level approx. +26dBu @ 100kΩ

Frequency Response

Mic input <10Hz to 43kHz (±3dB)

Line input <10Hz to 40kHz (±3dB)

Function Controls

GAIN variable ( +26dB to +60dB)

OUTPUT variable ( -∞ to +10dB)

Function Switches

20 dB PAD level attenuation (20dB)

+48 V activates the phantom power

PHASE REVERSE Phase reverse (180°)

LIMITER limits the output signal

Indicators

Input Level

8-segment LED meter:

-24, -18, -12, -6, 0, +6, +12, Clip

Power LED indicates operation

Power Supply

Adapter PSU

Mains Voltage

USA/Canada 120V~, 60Hz

Europe/U.K./Australia 230V~, 50Hz

China 220V~, 50Hz

Korea 220V~, 60Hz

Japan 100V~, 50 / 60Hz

Dimensions

Dimensions (H x W x D) approx. 64x 135x 135mm (2.5 x 5.3 x 5.3")

Weight approx. 2.2lbs / 1.0kg

BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,

modifications may be made from time to time to existing products without prior notice. Specifications and

appearance may differ from those listed or illustrated.

Page is loading ...

42 43Quick Start GuideTUBE ULTRAGAIN MIC100

1. Register online. Please register your

new MUSIC Group equipment right after you

purchase it by visiting behringer. com. Registering

your purchase using our simple online form helps

us to process your repair claims more quickly and

eciently. Also, read the terms and conditions of

our warranty, ifapplicable.

2. Malfunction.

Should your

MUSICGroup Authorized Reseller not be located

in your vicinity, you may contact the MUSIC Group

Authorized Fulller for your country listed under

“Support” at behringer. com. Shouldyour country

not be listed, please check if your problem can be

dealt with by our “OnlineSupport” which may

also be found under “Support” at behringer. com.

Alternatively, please submit an online warranty

claim at behringer. com BEFORE returning

theproduct.

1. Registro online. Le recomendamos

que registre su nuevo aparato MUSIC Group justo

después de su compra accediendo a la página

web behringer. com. Elregistro de su compra

a través de nuestro sencillo sistema online

nos ayudará a resolver cualquier incidencia

que se presente a la mayor brevedad posible.

Además,aproveche para leer los términos y

condiciones de nuestra garantía, si es aplicable

en sucaso.

2. Averías.

En el caso de que no exista un

distribuidor MUSIC Group en las inmediaciones,

puede ponerse en contacto con el distribuidor

MUSIC Group de su país, queencontrará dentro

del apartado “Support” de nuestra página

web behringer. com. En caso de que su país

no aparezca en ese listado, acceda a la sección

“Online Support” (quetambiénencontrará dentro

del apartado “Support” de nuestra páginaweb)

y compruebe si su problema aparece descrito y

solucionado allí. De forma alternativa, envíenos

a través de la página web una solicitud online

de soporte en periodo de garantía ANTES de

devolvernos el aparato.

Important information

Aspectos importantes

Other important information

1. Enregistrez-vous en ligne.

Prenez le temps d’enregistrer votre produit

MUSIC Group aussi vite que possible sur le site

Internet behringer. com. Le fait d’enregistrer

le produit en ligne nous permet de gérer les

réparations plus rapidement et plus ecacement.

Prenezégalement le temps de lire les termes et

conditions de notre garantie.

2. Dysfonctionnement. Si vous

n’avez pas de revendeur MUSIC Group près de

chez vous, contactez le distributeur MUSIC Group

de votre pays: consultez la liste des distributeurs

de votre pays dans la page “Support” de notre

site Internet behringer. com. Si votre pays n’est

pas dans la liste, essayez de résoudre votre

problème avec notre “aideen ligne” que vous

trouverez également dans la section “Support”

du site behringer. com. Vous pouvez également

nous faire parvenir directement votre demande

de réparation sous garantie par Internet sur le

site behringer. com AVANT de nous renvoyer

leproduit.

1. Online registrieren. Bitte

registrieren Sie Ihr neues MUSIC Group-

Gerät direkt nach dem Kauf auf der

Website behringer. com. Wenn Sie Ihren Kauf mit

unserem einfachen online Formular registrieren,

können wir Ihre Reparaturansprüche schneller

und ezienter bearbeiten. Lesen Sie bitte auch

unsere Garantiebedingungen, fallszutreend.

2. Funktionsfehler. Sollte sich

kein MUSICGroup Händler in Ihrer Nähe

benden, können Sie den MUSICGroup

Vertrieb Ihres Landes kontaktieren, derauf

behringer. com unter „Support“ aufgeführt

ist. Sollte Ihr Land nicht aufgelistet sein,

prüfen Sie bitte, ob Ihr Problem von unserem

„Online Support“ gelöst werden kann, den Sie

ebenfalls auf behringer. com unter „Support“

nden. Alternativ reichen Sie bitte Ihren

Garantieanspruch online auf behringer. com ein,

BEVOR Sie das Produktzurücksenden.

Informations

importantes

Wegitere wichtige

Informationen

Page is loading ...

We Hear You

Behringer Tube Ultragain MIC100 Quick start guide

This manual is also suitable for

Behringer Tube Ultragain MIC100 Quick start guide

in other languages

Related papers

Other documents