King KOP4800 Owner's manual

KOP4800 Installation Guide

QUESTIONS? (952) 345-8147

This guide contains installation and safety information

for your KING One Pro.

Please read thru this guide before using or installing

your KING One Pro.

Page 1

IMPORTANT SAFETY INFORMATION

DO NOT POWER WASH THE ANTENNA UNIT.

DO NOT OVER-TIGHTEN COAX CONNECTIONS.

1. Please read this safety information thoroughly before using or installing the KING One Pro.

2. Keep this safety information and the included Quick Reference Guide in a safe place for future

reference.

3. Follow all instructions and warnings. Set up, operate and install (optional) the KING One Pro in

accordance with the instructions.

4. Do not submerge the KING One Pro or place in standing water. Hand wash only with mild soap

and water.

5. Do not operate or store near any indoor or outdoor heat source such as radiators, heat

registers, stoves, barbecues, campres, or other items that produce heat.

6. Servicing may be required if the unit has been dropped or damaged in any way or if the unit

does not operate normally. Call KING Customer Service at (952) 345-8147.

7. Tighten all of the coax cable connections only by hand. If you use a wrench, you may

over-tighten the connections and damage your equipment.

8. To avoid risk of electrical shock, unplug your receiver before connecting/disconnecting the

KING One Pro in damp or wet conditions.

9. Always handle the KING One Pro carefully. Do not drop the KING One Pro. Avoid excessive

shock or vibration to the KING One Pro.

10. Use caution when carrying the KING One Pro. Always carry the KING One Pro by the handle.

11. Do not remove the cover of the KING One Pro without authorization. Doing so will void the

limited warranty.

12. Do not stack the KING One Pro on top of or below other electronic devices as this can cause

heat build-up or block the satellite signal from reaching the KING One Pro.

13. Keep the enclosure clean from dirt, bugs, and other debris by hand washing with mild soap and

water.

14. Do not coat or paint the KING One Pro with any substance.

15. The KING One Pro has been designed to be maintenance and trouble free. If not using the

KING One Pro for long periods of time, it is recommended that you set up the system on a

quarterly basis (every three months) to keep all moving parts of the KING One Pro in good

working order.

16. The KING One Pro can be secured to an object by looping a cable (sold separately) thru the

handle and attaching the cable to a secure object.

If you have any comments or questions, please contact KING Customer Service at (952) 345-8147,

or by email at [email protected].

Page 2

OPTIONAL MOUNTING ACCESSORIES

Allows you to easily use the antenna unit as

either a roof-mounted or portable antenna.

MB700

Quick Release Roof-Mount Kit

Although the antenna unit is designed to be mounted directly to the roof, the following two options are

also available.

Allows hanging of antenna unit on vehicle

window or included hanger bracket.

For stationary use only.

Vehicle must not be in motion while antenna

unit is on window or hanger bracket.

MB500

Mounting Bracket

The KING One Pro is not compatible with the MB100

Mounting Bracket. Use of MB100 will void warranty.

The use of any unauthorized

mounting bracket will void warranty.

MB160

Mounting Bracket

Allows you to position

your KING One Pro

almost anywhere

for best line of sight

to satellite. Keeps

antenna off the

ground away from

moisture.

TR1000

Tripod Mount

For temporary use when you don’t want to

put the antenna unit on the ground, KING

offers these two options.

See your dealer or the satellite antenna accessories page at kingconnect.com for details.

KING antenna not included with purchase of these products.

Page 3

You can cut the coax to length but you must terminate the coax with Snap-n-Seal

connectors. Otherwise, bundle and store excess coax in cabinet with receiver.

• • • • • IMPORTANT POINTS! • • • • •

The installer is responsible for determining the most appropriate fasteners to secure the

antenna unit to the roof. Depending on the roof material, fasteners such as lag screws, well

nuts, sheet metal screws, toggle bolts and T anchors may be used, and should always be

used in combination with a roof-compatible sealant.

The installer is responsible for properly securing the coax cable to the roof (for example,

cable ties and cable tie mounting pads).

The installer is responsible for weatherproong all holes (except drain holes in base) with

roof-compatible sealant.

If the rubber feet have been installed, remove them from the bottom of the unit.

DO NOT INSTALL UNIT ON ROOF WITH RUBBER FEET IN PLACE.

Do not put sharp bends in coax cables. This can reduce signal strength from the antenna.

Page 4

1. Select an area on the roof for the antenna unit and the location where the wiring will enter the

vehicle through the roof to the satellite receiver inside using the following criteria:

• A shorter distance between the antenna unit and the satellite receiver is most desirable.

• Make sure you have enough room to mount the antenna unit.

• The antenna unit should be mounted on the center line of the vehicle, and not tilted more than

2 degrees in any direction.

• There must be no line of sight obstructions. Air conditioning units, other antennas, and storage

areas that are too close to the antenna unit may prevent the satellite signal from reaching the

antenna unit.

• Mount the antenna unit with the handle to rear of the vehicle.

END-USER INSTALLATIONS: Many RVs are prewired with RG-6 coax cable for satellite antennas. Contact the

manufacturer of your RV or your local dealer to verify where this cable is located.

If prewired, run the existing coax cable from the prewired location in the roof to the antenna unit. When choosing the

antenna unit location, make sure the prewiring will reach the antenna unit.

ANTENNA UNIT LOCATION

ITEMS YOU WILL NEED

The CE2000 Cable Entry Cover (sold

separately) provides a watertight seal

where cables penetrate the roof (see the

satellite antenna accessories page at

kingconnect.com for more information).

Additional Items (sold separately):In the KING One Pro box:

Programming

Subscription

(3) Rubber Feet

Do not use rubber feet.

If installed on antenna unit,

remove before mounting.

Short Coax Cable

50’ RG-6

Coax Cable

Power Inserter

with Power Supply

Antenna Unit Receiver compatible

with your service*

*Some DIRECTV receivers require additional

components to enable satellite signal reception (page 9).

Visit kingconnect.com/support for additional receiver

compatibility information.

Cable(s)

TV

ANT REC

KC1170

You will also need a drill and drill

bits, roof-compatible sealant, and

appropriate fasteners to install all

components and wiring.

Page 5

HEIGHT OF

OBSTRUCTION

APPROXIMATE MINIMUM DISTANCE

TO EDGE OF ANTENNA UNIT

10” 8”

11” 10”

12” 12”

13” 14”

14” 16”

15” 18”

16” 20”

ANTENNA UNIT LOCATION

Page 6

2. Apply roof-compatible sealant to roof around entire area where fasteners will penetrate the roof.

Mount the antenna unit using the (4) mounting holes. After mounting unit, seal fastener heads

with roof-compatible sealant.

MAKE SURE YOU READ AND UNDERSTAND ALL OF THE IMPORTANT POINTS ON

PAGE 3 BEFORE BEGINNING THE INSTALLATION.

IF INSTALLED, REMOVE THE (3) RUBBER FEET FROM THE BOTTOM OF THE

ANTENNA UNIT. DO NOT ROOF MOUNT ANTENNA UNIT WITH FEET IN PLACE.

3. Connect one end of the RG-6 coax cable to the MAIN port and tighten connection (see below).

DO NOT OVER-TIGHTEN.

If using a second receiver, connect one end of second RG-6 coax (sold separately) to the AUX

port. Tighten connection. DO NOT OVER-TIGHTEN.

IMPORTANT!

Coax connections should be snug.

DO NOT OVER-TIGHTEN!

There are two coax ports on the back of the antenna unit. The one labeled “MAIN” MUST be connected to the KING

power inserter. The AUX port can be used for an additional receiver, or for DIRECTV SWM installations. Review the

wiring diagrams on pages 8-9 before routing your coax.

COAX ROUTING

ANTENNA UNIT MOUNTING

Page 7

6. Make interior connections shown on next page.

4. Run coax from the antenna unit to the roof edge, then along edge to location where coax will be

fed into the vehicle. If installing an optional second receiver, run second coax to location where it

will enter the vehicle. Secure (both) coax to roof every 12-18 inches (see below).

5. Drill 3/4” hole through the roof and into the cabinet where receiver is stored. Feed coax down

through hole. Seal opening with roof-compatible sealant so that it is completely waterproof

(inside and outside of the 3/4” hole). Repeat for second coax if present.

Installer is responsible for determining proper roof-compatible sealant.

All holes for cables and fasteners must be sealed so they are completely waterproof.

TYPICAL ROOF INSTALLATION - OVERHEAD VIEW

OPTIONAL: OEM INSTALLATION AND

END-USERS WITH CABLE ENTRY COVER:

Fasten cable entry cover to roof with

appropriate sealant and roof fasteners.

IMPORTANT!

Installer is responsible for

determining proper fasteners.

Mounting holes, perimeter of cable

entry cover and cable opening of

cable entry cover must be sealed

so they are completely waterproof.

Page 8

Use this page for DISH, Bell, and DIRECTV connections.

IMPORTANT! If you have a DIRECTV receiver H/HR25 or higher, make the connections shown on page 9

(requires DSWM30 Kit - sold separately).

Receivers sold separately

Coax sold separately

AUX MAIN

110 AC/DC

Power Supply

MAIN Receiver

Optional AUX Receiver

110 AC

SAT IN

110 AC

SAT IN

KING Power Inserter

Long RG-6 Coax Short Coax

ANT REC

DISH and Bell receivers with two SAT IN ports:

AUX coax may be connected to second SAT IN

port on main receiver for dual tuner usage

HAND-TIGHTEN COAX. OVER-TIGHTENING CAN DAMAGE CONNECTIONS.

POWER INSERTER FOR

INDOOR USE ONLY.

INTERIOR CONNECTIONS: DISH®, BELL™ AND DIRECTV®

Page 9

Sat 99°/101°

Power LED

SWM2 SWM1 PWR

18V 13V

For access to 101°satellite

programming, connect the

MAIN and AUX ports of the

antenna to both LNB inputs

labeled Sat 99°/101°

Not more than 100 ft of

total RG-6 coax between

antenna and DSWM30

Not more than 50 ft of RG-6

coax between antenna and

power inserter

Unused SWM outputs:

screw on dust cap

(no center pin)

Not necessary if DSWM30

is used in dry conditions

CONNECT COAX TO

PROPER INPUTS!

MAIN TO 18V

AUX TO 13V

AUX MAIN

DSWM30

110 AC

110 AC/DC

Power Supply

Optional Splitter for

more than one

receiver

To SWM Receivers

KC1194

4 Way SWM Splitter

MSPLIT 4R1-03

Receivers can be non-DVR or DVR receivers**

**If connecting to a DVR receiver, do not connect a coaxial cable

to the Satellite 2 input. With SWM, only connect to the

Satellite 1 port (labeled FTM or SWM)

Back of SWM Receiver

SAT IN (SWM-1)

110 AC/DC

Power Supply

SWM Power Inserter PI-29Z

(Do not use PI-21)

Power to SWM

Signal to IRD

KING Power Inserter

ANT REC

IMPORTANT! DIRECTV receivers H/HR25 and higher require use of components shown below.

NOTE: When using this connection diagram, you will not receive programming from the 119 satellite.

All items other than KING Antenna, KING Power Inserter (with power supply),

50’ coax, and short coax sold separately.

POWER INSERTER FOR INDOOR USE ONLY.

DO NOT use DSWM30H or your receiver

may be damaged.

DSWM30 is compatible with H21 or later

receivers and HR20 or later DVRs.

It is not compatible with D12 receivers.

11200 Hampshire Avenue South, Bloomington, MN 55438

PH 952.922.6889 || FAX 952.922.8424 || kingconnect.com

Simply better, by design.

™

Trademarks are the sole property of their respective owners.

KOP4800 Owner’s Manual

For use with DIRECTV® satellite programming

IMPORTANT!

The KING One Pro works with DIRECTV, DISH, and Bell TV. This manual is for DIRECTV

subscribers. Manuals for DISH and Bell subscribers are available at kingconnect.com.

Do not use this manual if you are a DISH or Bell subscriber.

Page 1

IMPORTANT!

The satellite TV market is expanding and changing. The information in this manual was accurate at the time

of printing. If your KING One Pro Satellite Antenna does not operate as outlined in this manual, please call

KING® at (952) 345-8147 or visit our website at kingconnect.com. KING is not responsible for changes outside

of its control.

CONTENTS

INTRODUCTION ...................................................... 2-3

IMPORTANT SAFETY AND CARE INFORMATION ................2

ABOUT SIGNAL LOSS ......................................3

SECURITY................................................3

SETUP ................................................................4

CONTENTS ...............................................4

APPLY RUBBER FEET TO ANTENNA UNIT .....................4

CONNECTIONS....................................................... 5-7

DIRECTV CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

DIRECTV CONNECTIONS WITH H/HR25 RECEIVER OR HIGHER...7

OPERATIONS ........................................................8-11

RECEIVER CONFIGURATION ................................8

ANTENNA CONFIGURATION............................... 8-9

SCAN FOR SATELLITES ................................ 10-11

TROUBLESHOOTING ...................................................12

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

LIMITED WARRANTY ...................................................14

FCC GUIDELINES ......................................................15

PRODUCT REGISTRATION

To provide ongoing technical support and to better

facilitate warranty processing, please register your product at

kingconnect.com/support.

Page 2

Thank you for choosing the premium KING One Pro Portable HDTV System!

The KING One Pro is factory programmed to work with DIRECTV. No antenna conguration is

required. (The conguration process is shown on pages 8-9 for future reference.)

INTRODUCTION

IMPORTANT SAFETY AND CARE INFORMATION

QUESTIONS? (952) 345-8147

1. Keep the Quick Reference Guide and Installation Guide that came with your KING One Pro in

a safe place for future reference. You may also print this on-line manual and keep it for future

reference as well.

2. Follow all instructions and warnings. Set up and operate the KING One Pro in accordance with

the instructions.

3. To avoid risk of electric shock, unplug your receiver before connecting/disconnecting the KING

One Pro in damp or wet conditions.

4. Tighten all of the coax cable connections by hand only. If you use a wrench, you may

over-tighten the connections and damage your equipment.

5. Always handle the KING One Pro carefully. Do not drop the KING One Pro. Avoid excessive

shock or vibration to the KING One Pro.

6. Use caution when carrying the KING One Pro. Always carry the KING One Pro by the handle.

7. Do not remove the cover of the KING One Pro without authorization. Doing so will void the

limited warranty.

8. Do not stack the KING One Pro on top of or below other electronic devices as this can cause

heat build-up or block the satellite signal from reaching the KING One Pro.

9. Do not operate or store near any indoor or outdoor heat source such as radiators, heat registers,

stoves, barbecues, campres, or other items that produce heat.

6. Servicing may be required if the unit has been dropped or damaged in any way or if the unit does

not operate normally. Call KING Customer Service at (952) 345-8147.

10. Do not power wash the KING One Pro.

11. Do not submerge the KING One Pro or place in standing water.

12. Keep the enclosure clean from dirt, bugs, and other debris by hand washing with mild soap and

water.

13. Do not coat or paint the KING One Pro with any substance.

The KING One Pro has been designed to be maintenance and trouble free. If not using the KING

One Pro for long periods of time, it is recommended that you set up the system on a quarterly basis

(every three months) to keep all moving parts of the KING One Pro in good working order.

If you have any comments or questions, please contact KING Customer Service at (952) 345-8147,

or by email at [email protected].

Page 3

ABOUT SIGNAL LOSS

SECURITY

OBSTRUCTIONS

The KING One Pro requires an unobstructed view of the southern sky for the best signal reception.

Be sure to place the KING One Pro in a location free from obstructions such as people, trees,

buildings, vehicles, etc. This will allow for the strongest signal and will help prevent any interruption to

your programming. Pointing the handle approximately north may speed up scan time.

RAIN AND SNOW FADE

Though rare, heavy rain, snow, or dense cloud cover

can reduce the satellite signal, which may interrupt

your programming. Your programming should return

as conditions improve.

ANTENNA

UNIT

OBSTRUCTIONS

SATELLITES IN

SOUTHERN SKY

KC1148

Place on a reasonably level surface

Pointing the handle approximately north

may speed up scan time, but is not

required for a successsful search

WHILE IN USE, DO NOT BLOCK THE ANTENNA

UNIT’S LINE OF SIGHT TO THE SATELLITES IN

THE SOUTHERN SKY AT ANY TIME!

IMPORTANT!

If you move the antenna unit any

time during or after the scan, you

will have to repeat the scan.

KC1168

The KING Antenna can be secured to an object by

looping a cable thru the handle.

Cable sold separately.

Page 4

SETUP

You will also need (sold separately):

DIRECTV

Programming

Subscription

(3) Rubber

Feet Short

Coax Cable

50’ RG-6

Coax Cable

Power Inserter

with Power Supply

Installation

Guide

Quick

Reference

Guide

Registration

Card

Antenna Unit

DIRECTV Receiver

For the most up-to-date receiver compatibility

information, go to kingconnect.com/support

Cable(s)

KC1193

TV

ANT REC

CONTENTS

APPLY RUBBER FEET TO ANTENNA UNIT

Do not

apply here.

Apply (3)

rubber feet

Soft, non-scratching surface

KC1153

IMPORTANT!

Do not apply rubber feet if roof-mounting the antenna unit.

See the Installation Guide included in the box.

Page 5

After connecting and plugging in all components, wait for the power inserter

LED to start ashing orange (about 10 seconds).

Go to page 8.

CONNECTIONS

HAND-TIGHTEN COAX.

OVER-TIGHTENING CAN

DAMAGE CONNECTIONS.

Make the connections on page 6 or page 7.

PAGE 6: Make these connections unless you have an H/HR25 or higher receiver.

PAGE 7: Make these connections if you have an H/HR25 or higher receiver.

(Requires DSWM30 Kit - sold separately)

• • • • • IMPORTANT POINTS! • • • • •

Connect all coax cables rst. Plug in power inserter and then receivers.

Power inserter is for indoor use only.

Place the power inserter in an accessible location.

Do not over-tighten the coax connections.

Do not put sharp bends or kinks in the cables.

Do not route the cables where they can be tripped on or run over by a vehicle.

NOTE: The KING One Pro will not receive channels broadcast from DIRECTV’s Ka band satellites at 99° and 103°.

When using page 7 connection diagram, you will not receive programming from the 119 satellite.

NOTE: If you wish to roof mount the antenna, see the Installation Guide that came with your KING One Pro.

Page 6

Receivers sold separately

Coax sold separately

AUX MAIN

110 AC/DC

Power Supply

MAIN Receiver

Optional AUX Receiver

110 AC

SAT IN

110 AC

SAT IN

KING Power Inserter

50’ RG-6 Coax Short Coax

ANT REC

KC1201

HAND-TIGHTEN COAX. OVER-TIGHTENING CAN DAMAGE CONNECTIONS.

POWER INSERTER FOR

INDOOR USE ONLY.

DIRECTV CONNECTIONS

Second receiver must be congured the same as the main receiver (see operation section).

Second receiver must be the same as main receiver (SWM vs. non-SWM).

If your main receiver has a second “satellite in” port and built in DVR, you can connect this input to the AUX port to

record programs on a different channel than the one you are watching.

Page is loading ...

King KOP4800 Owner's manual

King KOP4800 Owner's manual

Related papers

Other documents