IFM E80390 Operating instructions

IFM
Brand
IFM
Model
E80390
Type
Operating instructions

This manual is also suitable for

IFM E80390 is an RFID antenna adapter that can be used to enhance the performance of compatible RFID read/write heads. It is designed to increase the range and detection zone of the read/write head, making it ideal for applications where reliable and efficient RFID communication is crucial.

Key Features:

  • Increased Range: E80390 significantly extends the detection range of the RFID read/write head, allowing for longer read and write distances. This is particularly beneficial in applications where tags are located at a distance or in hard-to-reach areas.

  • Expanded Detection Zone: By modifying the field characteristics of the read/write head, E80390 creates a wider detection zone. This means that tags can be detected within a larger area, reducing the chance of missed reads and improving overall system efficiency.

IFM E80390 is an RFID antenna adapter that can be used to enhance the performance of compatible RFID read/write heads. It is designed to increase the range and detection zone of the read/write head, making it ideal for applications where reliable and efficient RFID communication is crucial.

Key Features:

  • Increased Range: E80390 significantly extends the detection range of the RFID read/write head, allowing for longer read and write distances. This is particularly beneficial in applications where tags are located at a distance or in hard-to-reach areas.

  • Expanded Detection Zone: By modifying the field characteristics of the read/write head, E80390 creates a wider detection zone. This means that tags can be detected within a larger area, reducing the chance of missed reads and improving overall system efficiency.

Operating instructions
RFID antenna adapter
E80390
E80391
11532054 / 0005 / 2023
GB
E80390 E80391 RFID antenna adapter
2
Contents
1 Preliminary note ............................................................. 3
1.1 Symbols used.......................................................... 3
1.2 Legal and copyright information ............................................ 3
2 Safety instructions............................................................ 4
3 Intended use................................................................ 5
4 Installation.................................................................. 6
4.1 Installing E80390 ....................................................... 6
4.1.1 Installation to a mounted RFID read/write head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1.2 Installation to a non-mounted RFID read/write head . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 Installing E80391 ....................................................... 7
5 Technical data............................................................... 8
5.1 E80390 detection range .................................................. 8
5.2 E80391 detection range .................................................. 8
6 Maintenance, repair and disposal................................................ 9
7 Approvals/standards.......................................................... 10
RFID antenna adapter E80390 E80391
3
1 Preliminary note
You will find instructions, technical data, approvals and further information using the QR code on the
unit / packaging or at documentation.ifm.com.
1.1 Symbols used
Requirement
Instructions
Reaction, result
[...] Designation of keys, buttons or indications
Cross-reference
Important note
Non-compliance may result in malfunction or interference.
Information
Supplementary note
1.2 Legal and copyright information
© All rights reserved by ifm electronic gmbh. No part of these instructions may be reproduced and
used without the consent of ifm electronic gmbh.
All product names, pictures, companies or other brands used on our pages are the property of the
respective rights owners.
E80390 E80391 RFID antenna adapter
4
2 Safety instructions
General
• The unit described is a subcomponent for integration into a system.
– The system architect is responsible for the safety of the system.
– The system architect undertakes to perform a risk assessment and to create documentation in
accordance with legal and normative requirements to be provided to the operator and user of
the system. This documentation must contain all necessary information and safety instructions
for the operator, the user and, if applicable, for any service personnel authorised by the
architect of the system.
• Read this document before setting up the product and keep it during the entire service life.
• The product must be suitable for the corresponding applications and environmental conditions
without any restrictions.
• Only use the product for its intended purpose (Ò Intended use).
• If the operating instructions or the technical data are not adhered to, personal injury and/or damage
to property may occur.
• The manufacturer assumes no liability or warranty for any consequences caused by tampering with
the product or incorrect use by the operator.
• Installation, electrical connection, set-up, operation and maintenance of the product must be
carried out by qualified personnel authorised by the machine operator.
• Protect units and cables against damage.
Radio equipment
In general, radio equipment must not be used in the vicinity of petrol stations, fuel depots, chemical
plants or blasting operations.
uDo not transport and store any flammable gases, liquids or explosive substances near the unit.
Interference of electronic and medical devices
Operation can affect the function of electronic devices that are not correctly shielded.
uDisconnect the device in the vicinity of medical equipment.
uContact the manufacturer of the corresponding device in case of any interference.
RFID antenna adapter E80390 E80391
5
3 Intended use
The articles E80390 and E80391 are accessories for the M18 and rectangular type RFID read/write
heads. The accessories are used to change the field of the connected RFID read/write heads. This
leads to the following effects depending on the installation of the accessories:
• higher range
• larger detection zone
• smaller detection zone
E80390 E80391 RFID antenna adapter
6
4 Installation
4.1 Installing E80390
E80390 is suitable for being installed on an M18 type RFID read/write head (e.g. DTM424 / DTM425).
There are two ways to install the E80390:
• Installation to a mounted RFID read/write head (Ò Installation to a mounted RFID read/write
head/6)
• Installation to a non-mounted RFID read/write head (Ò Installation to a non-mounted RFID read/
write head/6)
If E8039x is mounted on metal or in the vicinity of metal, the range of the RFID read/write head
is reduced.
uMount the E8039x at least 100 mm away from metal objects.
1
①Mounting holes
4.1.1 Installation to a mounted RFID read/write head
The E8039x RFID antenna adapter changes the field characteristics of a mounted RFID read/write
head in operation.
Installing the E8039x RFID antenna adapter to a mounted RFID read/write head:
uScrew the E80390 to the RFID read/write head by hand (see figure above).
wUse a maximum tightening torque of 0.6 Nm.
uUse the mounting holes ① to fix the E80390 to a suitable surface.
wFor a permanently reliable installation, the E80390 is additionally fastened to a suitable surface
using the mounting holes.
4.1.2 Installation to a non-mounted RFID read/write head
The E8039x RFID antenna adapter changes the field characteristics of a mounted RFID read/write
head in operation.
Installing the E8039x RFID antenna adapter to a non-mounted RFID read/write head:
uScrew the RFID read/write head into the E80390 by hand.
RFID antenna adapter E80390 E80391
7
wUse a maximum tightening torque of 0.6 Nm.
uUse the mounting holes ① to fix the E80390 to a suitable surface.
uAdditionally fasten the RFID read/write head.
wFor a permanently reliable installation, the RFID read/write head is additionally fastened to a
suitable surface using the M18 thread.
uLay and connect the cable of the RFID read/write head.
wThe electrical connection is described in the operating instructions of the RFID read/write head.
4.2 Installing E80391
E80391 is suitable for mounting to a rectangular type RFID read/write head (e.g. ANT515 / ANT516).
For the installation of E80391 the RFID read/write head must not be mounted.
If E8039x is mounted on metal or in the vicinity of metal, the range of the RFID read/write head
is reduced.
uMount the E8039x at least 100 mm away from metal objects.
1
①Mounting holes
Installing the E80391:
uPlace the RFID read/write head in the cut-out of the E80391 (see figure above).
wThe sensing face of the RFID read/write head must point in the direction of the E80391.
uScrew the RFID read/write head to the E80391 with 2x M3x6 lens screws.
uUse the mounting holes ① to fix the E80391 to a suitable surface.
E80390 E80391 RFID antenna adapter
8
5 Technical data
5.1 E80390 detection range
The figure below shows the detection zone of an ANT421 with and without E80390. A 50 mm tag
(E80384) was used for the measurement.
020 40 60 80 10020406080100
100
80
60
40
20
[mm]
[mm]
1
2
Fig.1: Detection range of an ANT421
①ANT421 with E80390
②ANT421 without E80390
5.2 E80391 detection range
The figure below shows the detection zone of an ANT515 with and without E80391. A 50 mm tag
(E80384) was used for the measurement.
020 40 60 80 10020406080100
100
80
60
40
20
[mm]
[mm]
1
2
Fig.2: Detection range of an ANT515
①ANT515 with E80391
②ANT515 without E80391
RFID antenna adapter E80390 E80391
9
6 Maintenance, repair and disposal
The unit is maintenance-free.
uContact ifm in case of malfunction.
uDo not open the housing as the unit does not contain any components which can be maintained by
the user. The unit must only be repaired by the manufacturer.
uClean the device using a dry cloth.
uDispose of the unit in accordance with the national environmental regulations.
E80390 E80391 RFID antenna adapter
10
7 Approvals/standards
For approvals and standards, the following information is available:
• Test standards and regulations: documentation.ifm.com
• EU declaration of conformity and approvals: documentation.ifm.com
• Notes relevant for approval: Package insert of the device and documentation.ifm.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

IFM E80390 Operating instructions

IFM
Brand
IFM
Model
E80390
Type
Operating instructions
This manual is also suitable for

IFM E80390 is an RFID antenna adapter that can be used to enhance the performance of compatible RFID read/write heads. It is designed to increase the range and detection zone of the read/write head, making it ideal for applications where reliable and efficient RFID communication is crucial.

Key Features:

  • Increased Range: E80390 significantly extends the detection range of the RFID read/write head, allowing for longer read and write distances. This is particularly beneficial in applications where tags are located at a distance or in hard-to-reach areas.

  • Expanded Detection Zone: By modifying the field characteristics of the read/write head, E80390 creates a wider detection zone. This means that tags can be detected within a larger area, reducing the chance of missed reads and improving overall system efficiency.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents