jWIN JD-VD742 User manual

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

PORTABLE DVD PLAYER WITH 7”

ACTIVE-MATRIX TFT LCD SCREEN

INSTRUCTION MANUAL

JD-VD742

Please read this manual carefully before operating and save it for future reference.

Have a question? Please visit www.jWIN.com for more detailed information.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 1 - www.jWIN.com

USER SAFETY GIUDE

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

These markings are located on the bottom, side or back of the unit.

CAUTION: To prevent the risk of electric shock, do not remove cover (or back). Non- user-

serviceable parts inside. Refer servicing to a service professional.

• The lightning flash with an arrowhead symbol, within an equilateral triangle, is intended to

alert the user to the presence of un-insulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to a

person.

• The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating, maintenance and servicing instructions in the literature

accompanying the appliance.

Dripping warning: "This product shall not be exposed to any dripping or splashing, and no

objects filled with liquids, such as vases, shall be placed on or near the product."

Ventilation warning: "The normal ventilation of the product shall not be impeded for intended

use." (Minimum distances must be kept around the apparatus for sufficient ventilation, especially

while use of the apparatus is in tropical and/or moderate climates.)

Dispose of old batteries safely. Do not throw them into a fire.

LASER SAFETY

This unit utilizes laser technology. Only a qualified professional should

remove the cover or attempt to service this device, due to possible eye injury.

CAUTION

• Use of controls or adjustments or performance of procedure other than

specified herein may result in hazardous radiation exposure.

• Hazardous laser radiation when open and interlock defeated.

DANGER

Invisible laser radiation when open and interlock failure. Avoid direct exposure

to beam.

CLASS 1 LASER

PRODUCT

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 2 - www.jWIN.com

USER SAFETY GIUDE

INSTRUCTIONS ON ENVIRONMENT PROTECTION

Do not dispose of this product in the usual household garbage at the end of its life

cycle; bring it to a collection point for the recycling of electrical and electronic

appliances. This symbol on the product means the instructions for use or the

packing will inform about the methods for disposal. The materials are recyclable as

mentioned in its marking. By recycling, material recycling, or other forms of re-

utilization of old appliances, you make an important contribution to protect the

environment. Please inquire at your local community administration for the authorized

disposal location.

IMPORTANT SAFETY PRECAUTIONS

1. READ INSTRUCTIONS - All safety and operating instructions should be read before the

appliance is operated.

2. RETAIN INSTRUCTIONS - The safety and operating instructions should be retained in a

secure place for future reference.

3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be

observed.

4. FOLLOW INSTRUCTIONS - All operating and use instructions should be followed.

5. WATER AND MOISTURE - The appliance should not be used near water. For example: near a

bathtub, kitchen sink, laundry tub, and swimming pool or even in a wet basement.

6. VENTILATION - The appliance should be situated so that its location and position does not

interfere with its proper ventilation. For example, the appliance should not be situated on a bed,

sofa, rug or similar surface that may block the ventilation openings; or, be placed in a built-in

installation, such as a bookcase or cabinet that may impede the flow of air through the

ventilation openings.

7. HEAT - The appliance should be situated away from heat sources such as radiators, heat

registers, stoves, or other appliances (including amplifiers) that produce heat.

8. POWER SOURCES - The appliance should be connected to a power supply only of the type

described in the operating instructions or as marked on the appliance.

9. GROUNDING AND POLARIZATION - Precautions should be taken to ensure that the

grounding or polarization of the appliance is correct.

10. POWER CORD PROTECTION - Power supply cords should be routed so that they are not

likely to be walked on or obstructed by items placed upon or against them. Pay particular

attention to cords at plugs, convenience receptacles, and the point at which they exit from the

appliance.

11. CLEANING - The appliance should be cleaned only as recommended by the manufacturer.

12. POWER LINES - An outdoor antenna should be located away from power lines.

13. NONUSE PERIODS - The power cord of the appliance should be unplugged from the outlet

when the appliance is to be left unused for an extended period of time.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 3 - www.jWIN.com

USER SAFETY GIUDE

IMPORTANT SAFETY PRECAUTIONS – CONTINUED

14. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are

not spilled into the device’s openings.

15. CARTS AND STANDS - The appliance should be used only with a cart or

stand that is recommended by the manufacturer. An appliance and cart

combination should be moved with care. Quick stops, excessive force, and

uneven surfaces may cause the appliance and cart combination to overturn.

16. WALL OR CEILING MOUNTING - If the appliance is mounted to a wall or ceiling, it should

be mounted only as recommended by the manufacturer.

17. DAMAGE REQUIRING SERVICE - The appliance should be serviced by qualified service

professional when:

a. The power-supply cord or plug has been damaged.

b. Objects have fallen into, or liquid has been spilled into the appliance’s apertures.

c. The appliance has been exposed to rain.

d. The appliance has been dropped and suffered damage.

e. The appliance does not appear to operate normally or exhibits a marked change in

performance.

18. SERVICING - The user should not attempt to service the appliance beyond that described in

the user's operating instructions. All other servicing should be referred to qualified service

professional.

19. OUTDOOR ANTENNA GROUNDING - If an outside antenna is connected to the receiver, be

sure that the antenna system is grounded so as to provide some protection against voltage

surges and built up static charges.

Section 810 of the National Electrical

Code, ANS/NFPA No. 70-1984

provides information with respect to

proper grounding of the mast and

supporting structure, grounding of the

lead-in wire to an antenna discharge

unit, size of grounding conductors,

location of antenna discharge unit,

connection to grounding electrodes,

and requirements for the grounding

electrode.

20. PROTECTIVE ATTACHMENT PLUG - The appliance is equipped with an attachment plug

that has an overload protection. This is a safety feature. If replacement of the plug is

required, be sure the service technician has used a replacement plug specified by the

manufacturer that has the same overload protection as the original plug. (UK Version Only)

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 4 - www.jWIN.com

USER SAFETY GIUDE

FCC NOTICE (USA)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this

device does not cause harmful interference.

• FCC regulations state that any change or modification to the equipment, not expressly

approved by maker or its authorized parties, could void user’s authority to operate this

equipment.

• To prevent fire or electric shock, do not expose the unit to rain or moisture.

• Never attempt to open the cabinet. Dangerous high voltages are present in the unit. Always

refer servicing to a qualified technician.

IC NOTICE (CANADA)

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus as set out in the Radio Interference Regulations of Industry Canada. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television operation

(which can be determined by turning the equipment off), the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 5 - www.jWIN.com

CONTENTS

GETTING STARTED

• Compatibility ……………………………………………………………………………………

7

• Introduction …………………………………………..………………………………………...

8

• Location of controls on the remote control...………………………………………………..

9

• Location of controls on the main unit…………….…………………………………………..

10

• Battery installations ………………………..…………………………………………………..

11

• Using the AC adapter ………………………………………………………………………….

11

• Charging the battery …………………………………………………………………………..

12

• Quick connection guide ………………………………………………………..……………...

13

OPERATIONAL INSTRUCTIONS

• Playing DVD / VCD / Audio CD...……………………………………………………………..

14

• Resume / Key Lock / Skip / Slow Motion / Pause / Step / Search ………….…………….

15

• Chapter / Title Time Search / Repeat ………………………………………………………..

16

• A-B repeat / Random / Programmed Playback …………………………………………….

17

• Audio / Menu / Subtitle / Title Menu / 3D Sound / Mute / Bookmark ...………...………...

18

• Zoom / Multi-Angle / Display / PBC ………………………………………………………….

19

• Digest function …………………………………………………………………………………

20

• Playing JPEG CD …………………………………...…………………………………………

20

• On-Screen Dialog Box / Playing MP3 CD …………………………………………………..

21

• Selecting MP3 folders/tracks using number buttons …………..…………………………..

22

• Going back to the previous MP3 folder menu ……………………………..……………….

22

• Repeat play with MP3 files ……………………………………………………………………

22

• MP3 program setting procedure ……………………………………………………………

23

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 6 - www.jWIN.com

CONTENTS

SETUP PAGES

• Navigating the setup pages ……………..…...…..…………………………………………..

24

• General setup page ……………..…...………………………………………………………..

25

• Speaker setup page……………………………………………………………………………

25

• Video setup page ………………………………………………………………………………

25

• Preference setup page ………………………………………………………………………..

26

OTHERS

• Maintenance ……………………………………………………………………………………

27

• Troubleshooting ……………..…..……………………………………………………………..

28

• Specifications …………………………………………………………………………………..

30

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 7 - www.jWIN.com

GETTING STARTED

COMPATIBILITY

AUDIO AND VIDEO

• Disc Size: 12cm / 8cm

• Disc Type: DVD

o Single side, single layer

o Single side, double layer

o PAL / NTSC

AUDIO AND VIDEO

• Disc Size: 12cm / 8cm

• Disc Type: SVCD / VCD

AUDIO

• Disc Size: 12cm / 8cm

• Disc Type: CD

Note: Only the above types of discs can be played on this unit. DVD-ROM, CD-ROM, CDV, etc.

cannot be played. Some CD-R, CD-RW discs cannot be played depending on the condition of the

player and the disc. This unit is to be used exclusively with the NTSC or PAL color system.

SECAM system discs cannot be used with this unit.

DVD

DVD discs are divided into titles, and the titles are subdivided into chapter.

AUDIO CD

Music CD discs are divided into tracks.

This product incorporates copyright protection technology that is protected by method claims of

certain US patents and other intellectual property rights owned by Macrovision Corporation and

other rights owners. Use of this copyright protection technology must be authorized by

Macrovision Corporation, and is intended for home and other limited viewing uses, only unless

otherwise authorized by the Macrovision Corporation. Reverse engineering or disassembly is

prohibited.

Appartus claims of US Patent Nos. 4,631.603; 4,819.098; 4,907.093; 5,315.448 and 6,516.132;

licensed for limited viewing uses only.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 8 - www.jWIN.com

GETTING STARTED

Thank you for purchasing JD-VD742. Unpack the unit and make sure all the accessories are put

aside so they will not be lost. We recommend that you retain the original carton and packaging

materials for use should you transport or ship the unit in the future.

General Features

• Portable DVD player with 7” TFT wide screen LCD

• Built-in Dolby

®

decoder

• Compatible with NTSC / PAL system

• Coaxial digital audio and S-video output

• AV input and output

• Stereo headphone jack

• Rechargeable battery

• Built-in stereo speakers

• Multiple OSD / menu / subtitle / audio languages

• Zoom operation and repeat playback

• Playable media: DVD / VCD / Audio CD / MP3 CD / CD-R / CD-RW

What’s Included

• Portable DVD Player

• Remote Control

• AC Adapter

• Car Adapter

• Audio Cable

• Video Cable

• Rechargeable Battery Pack

• Instruction manual

• Warranty card

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 9 - www.jWIN.com

GETTING STARTED

LOCATION OF CONTROLS ON THE REMOTE CONTROL

1. KEY LOCK BUTTON

2. NUMBER 0 TO 9 BUTTON

3. DVD MENU BUTTON

4. TITLE MENU BUTTON

5. PBC BUTTON

6. DISPLAY BUTTON

7. NAVIGATION (///) BUTTON

8. RETURN BUTTON

9. BOOKMARK BUTTON

10. SLOW/R BUTTON

11. PAUSE/STEP BUTTON

12. RANDOM BUTTON

13. MUTE BUTTON

14. REPEAT/REPEAT A-B BUTTON

15. SEARCH FORWARD BUTTON

16. SEARCH REVERSE BUTTON

17. SKIP FORWARD BUTTON

18. SKIP REVERSE BUTTON

19. SLOW/F BUTTON

20. STOP BUTTON

21. PROGRAM BUTTON

22. SEARCH BUTTON

23. ENTER BUTTON

24. PLAY BUTTON

25. SETUP BUTTON

26. 3D BUTTON

27. ANGLE BUTTON

28. SUBTITLE MENU BUTTON

29. AUDIO MENU BUTTON

30. AUDIO MODE BUTTON

31. ZOOM BUTTON

32. CLEAR BUTTON

33. DIGEST BUTTON

34. STANDBY ON/OFF BUTTON

35. SCREEN ON/OFF BUTTON

• Point remote control unit no more than 6m from the remote sensor and within about 30° of

the front of the unit.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 10 - www.jWIN.com

GETTING STARTED

LOCATION OF CONTROLS ON THE MAIN UNIT

• Front View

1. OPEN SLIDE SWITCH

2. FULL INDICATOR

3. CHARGE INDICATOR

4. STANDBY INDICATOR

5. REMOTE SENSOR

6. POWER SLIDE SWITCH

• Right Side View

7. VOLUME KNOB

8. PHONES JACK

9. INPUT / OUTPUT LINE SELECTOR

10. AUDIO JACK

11. VIDEO (COMPOSITE) JACK

12. COAXIAL DIGITAL AUDIO OUTPUT JACK

13. DC IN JACK

• Expansion View

14. TFT DISPLAY

15. SPEAKERS

16. DISC COMPARTMENT

17. DISC COMPARTMENT OPEN BUTTON

18. SETUP BUTTON

19. DISPLAY BUTTON

20. DVD MENU BUTTON

21. TITLE MENU BUTTON

22. SKIP REVERSE BUTTON

23. SKIP FORWARD BUTTON

24. PAUSE BUTTON

25. STOP BUTTON

26. PLAY BUTTON

27. NAVIGATION (///) BUTTONS

28. ENTER BUTTON

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 11 - www.jWIN.com

GETTING STARTED

REMOTE CONTROL BATTERY INSTALLATION

Before starting to operate the remote control, please pull out the

insulation plate from the battery compartment.

1. Pull out the battery holder as shown right.

2. Place one battery (CR 2025) as shown right. Make sure that

the polarity (+/–) of battery matches the marks inside the

unit.

3. Insert the battery holder into its compartment as shown right.

Note: Do not attempt to recharge, short-circuit, disassembly,

heat or throw the batteries into the fire.

RECHARGEABLE BATTERY INSTALLATION

The rechargeable battery pack is included in the package as separately packed.

1. Loading the rechargeable battery

• Unpack the rechargeable battery.

• Insert it into the slot at the back of the main unit as

shown left. If properly inserted, you will hear the

“CLICK!” sound.

Note: For the first time use, please charge the battery

fully first before use. It will take approximately 3 hours

to fully charge it.

2. Loading the rechargeable battery

• Push and hold the lock button down at the back of

the main unit as shown right.

• Push the installed battery back to release.

USING THE AC ADAPTER

1. Insert the DC plug at the end of the adapter cord

into the DC ‘IN’ jack at the right side of the player.

2. Plug the other end into an AC wall outlet.

Notes:

• Only use with the supplied AC adapter. Using with

another AC adapter could cause damage.

• Remove both the DC plug and AC plug to

disconnect the AC adapter when not necessary.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 12 - www.jWIN.com

GETTING STARTED

CHARGING THE BATTERY

After loading the battery, refer to the “Using the AC Adapter” section in this manual to connect to

the power converter.

Notes:

• When using the Ni-MH rechargeable battery, please note that you must FULLY CHARGE

THE BATTERY. If not done so, the discharging time will be short.

• The battery will be operated normally with normal capacity after 4~5 times of charging and

discharging. It is not a defect or abnormal battery.

• After a period of storage, or non-usage for an extended period of time, the device will require

users to repeat the above mentioned steps to get the battery back to normal condition.

• The battery is fully charged for approximately 3 hours after the AC adaptor is connected.

While the battery is charging the CHARGE indicator at the front will light up RED. And when

charging is completed, the FULL indicator will light up GREEN.

Notes:

• Disconnect the AC adapter plugs from both the player and the AC outlet, when charging is

completed or not necessary.

• The battery recharge circuit operates on both power ON and OFF mode. Switch the unit OFF

for battery quick recharge.

• When battery is fully charged and released from unit, the CHARGE indicator will light up RED.

It then means the charge circuit is ON.

BATTERY LOW INDICATION

When using the rechargeable battery to play and the battery is nearly exhausted, a

“STANDBY” indicator in the front of the player will begin blinking. After some time,

the power will turn OFF automatically. Refer to “Charging the Battery” to recharge

the battery.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 13 - www.jWIN.com

GETTING STARTED

CONNECTING THE AC ADAPTER OR CIGARETTE LIGHTER ADAPTER

Connect the DC plug at the end of the AC adapter cord, or connect the cigarette lighter adapter

into the DC IN jack at the side of the unit. Plug the other end into the cigarette lighter socket or

into the power outlet.

SYSTEM CONNECTION

Use the audio cable (Red / White) and video cable (Yellow) to connect from the DVD player to a

TV set and an amplifier.

CONNECTING THE DVD PLAYER TO A TV SET BY AV

CABLE

Use the audio cable (Red / White), video cable (Yellow) to

connect the Player and TV set.

CONNECTING THE DVD PLAYER TO STEREO RECEIVER

BY COAXIAL OUTPUT

Use audio cable with 3.5mm stereo plug to unit, and next end

with white color RCA plug to connect stereo receiver with

coaxial digital in jack.

CONNECTING OTHER MEDIA TO THE DVD PLAYER

Use the audio cable (Red / White), video cable (Yellow) to

connect from other media to the DVD player.

Note: Slide the Line Select switch to “IN“.

Notes for Cable Connections:

• Audio Cable (one end with 3.5mm stereo headphone

plug, and two ends with Red / White RCA plug).

• Video Cable (one end with 3.5mm stereo headphone

plug, and one end with Yellow RCA plug).

• Coaxial output (one end with 3.5mm stereo headphone

plug, and one end with White RCA plug).

Turn the power OFF and keep the DC cord pulled out from the adapter when connecting to the

system!

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 14 - www.jWIN.com

OPERATIONAL INSTRUCTIONS

PLAYING DVD / VCD / AUDIO CD

1. To power the unit ON, slide the POWER switch to the left, and then the unit will turn ON.

Note:

• To see the movie on the LCD screen of JD-VD742, the LINE SELECT IN/OUT switch

must be at the ‘OUT’ position. If not, slide the LINE SELECT IN/OUT switch to the ‘OUT’

position.

2. Press the DOOR OPEN button to open up

the disc compartment door. The ‘OPEN’

indication will appear on the LCD screen.

3. Place the disc with the label side facing front

on the disc tray. Hold the disc without

touching either of its surfaces, placing the

printed title side facing up.

4. Push down the left front edge on the door to

close and secure. The disc will start playback

automatically.

Note:

• Loading the disc in any source mode will

switch from the current mode to DISC

mode.

• For MP3 disc, the disc reading time may

exceed a little bit longer, due to the large number of songs complied into one disc.

NOTE: If playing an MP3 Disc, MENU will appear on the LCD screen:

• Use the navigation buttons (///) to select the desired item.

• Press the ENTER button, and playback of the selected item will start.

5. Adjust the Volume knob to a comfortable level.

Note: When in Play mode and the “STANDBY” indicator is blinking, it signifies the battery is

nearly exhausted and must be recharged.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 15 - www.jWIN.com

OPERATIONAL INSTRUCTIONS

RESUME FUNCTION

1. Press the STOP button once to stop play. The screen will show "Press Play Key To

Continue".

2. Press the PLAY button, the play will start automatically from the point where you stopped

(resuming playback). Note that some discs may not resume automatic playback.

3. If the STOP button is pressed twice, the screen shows STOP. Then, the player will stop

completely.

KEY-LOCK FUNCTION

1. Press the KEY LOCK button to lock the key. The “Key Lock On” indication appears on the

LCD screen, and the function keys on the main unit will be disabled with the exception of the

power button.

2. Press the KEY LOCK button again to make all buttons function again.

SKIP FUNCTION

Press  or  to skip to the previous or next chapter (DVD) or track (CD)

SLOW-MOTION FUNCTION

Press this button to select slow-motion forward or rewind playback at 1/2, 1/4, 1/8, and 1/16

without sound.

Note: This player does not support slow-motion playback for audio CD, and slow-

motion rewind (SLOW/R) does not support playback for the VCD disc. The indication

shown right will appear on the LCD screen when it doesn’t support the slow-motion

function.

PAUSE/STEP FUNCTION

1. Press button once to pause the picture.

2. Press the PAUSE/STEP button to play the DVD one frame at a time.

SEARCH FUNCTION

1. The () and () button allows searching forward / backward with the speed up to 16 times

faster than the normal speed. Each press of the search button will change the speed as

follows: x2 / x4 / x8 / x16

2. Press the PLAY button to resume the normal playback.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 16 - www.jWIN.com

OPERATIONAL INSTRUCTIONS

CHAPTER SEARCH FUNCTION

Use this feature to directly go to a specific title and/or chapter.

1. Press the SEARCH button once.

2. Use the numeric buttons to input the desired chapter number.

TITLE TIME SEARCH FUNCTION

Use this feature to directly go to a specific title time.

1. Press the SEARCH button twice.

2. Use the numeric buttons to select the desired time.

Notes: If the search function is attempted during the play mode, you can only go to a specific

chapter or time. You cannot change the title number. If you enter a time that exceeds the time

limit of DVD, “INPUT INVALID” will appear on the LCD screen. When playing VCD, the numeric

buttons only can be used to select the desired track or time in the search mode.

REPEAT FUNCTION

1. DVD Disc

• While in the Playback mode, press the REPEAT button once; “

CHAPTER” will appear

briefly on the LCD screen and the currently playing chapter will repeat continuously.

• While in the Playback mode, press the REPEAT button a second time; “

TITLE” will

appear briefly on the LCD screen and the current playing title will repeat continuously.

• Press the REPEAT button once more to cancel the REPEAT mode.

2. Audio CD / VCD Disc

• To repeat a track, simply select the track as described on the previous page, and then

press the REPEAT button once; “

TRACK” will appear on the LCD screen and the unit

will repeat the selected track continuously until the STOP button is pressed.

• To repeat play all tracks on a CD, press the REPEAT button a second time; “

ALL” will

appear on the LCD screen, and the unit will repeat the CD continuously until the STOP

button is pressed.

• To cancel the repeat play, press the REPEAT button until “OFF” is shown on the LCD

screen.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 17 - www.jWIN.com

OPERATIONAL INSTRUCTIONS

A-B REPEAT FUNCTION

This player can repeatedly play back a specific section.

1. While in the play mode, press the ‘A-B’ button to define where you want the section to start.

2. Press the ‘A-B’ button again to define where you would like the section to end, and the unit

will then play the selected area continuously.

3. To cancel the A-B repeat mode, press the ‘A-B’ button again until the icon disappears on the

screen.

RANDOM FUNCTION

1. Press the RANDOM button once and “RANDOM” will appear on the LCD screen.

2. Press the PLAY button and the unit will play all the tracks back in random order. After all

tracks have been randomly played, the unit will automatically stop playing and enter into the

STOP mode.

3. To cancel the random function, press the RANDOM button a second time. “OFF” will be

shown on the LCD screen.

Note: When playing audio CD, MP3 CD or other audio media discs, you can press the “SCREEN

ON/OFF” button to turn off the LCD screen temporarily. This will save more power when using

rechargeable battery for playing.

PROGRAMMED PLAYBACK (DVD/CD/VCD)

You can program 20 different tracks or you can also program certain tracks to play more than

once.

1. Press the PROGRAM button. The program window will appear on the screen.

2. Press the numeric buttons to input 2 numbers for each track: one for title and the other for

chapter. After inputting 2 numbers, the cursor will automatically jump to the next program

track, awaiting the input of the next numbers.

3. Repeat step 2 until all the desired titles and chapters have been programmed (up to 20). You

can repeat a title and a chapter more than once if desired.

4. Use the navigation buttons to select the “START” position and press the PLAY button to

begin the programmed play.

5. To cancel the Program function, press the STOP button twice, or press the DOOR OPEN

button.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 18 - www.jWIN.com

OPERATIONAL INSTRUCTIONS

AUDIO FEATURE

For DVD, Pressing the AUDIO MENU button will allow you to change the audio language from

the one selected at the initial settings to a different language, if available. This feature is not

available on all discs. For audio CD and VCD, pressing the AUDIO MODE button will change the

audio mode as follows: MONO LEFT / MONO RIGHT / MIX MONO / STEREO

MENU FEATURE

Press the DVD MENU button, and the main menu of the DVD disc will appear. Use the navigation

buttons to select the desired option, and then press the ENTER button to confirm. Some discs

may not support this feature.

SUBTITLE FEATURE

Press the SUBTITLE button to select a subtitle language. To turn off the subtitle, press the

SUBTITLE button repeatedly. This feature is not available on all discs.

TITLE MENU FEATURE

Press the TITLE MENU button. The title menu of the disc will appear on the screen. Use the

navigator buttons to select the desired option, and then press the ENTER button to confirm. This

feature is not available on all discs.

3D SOUND

During playback of a disc, press the 3D button repeatedly to change the sound mode as follows:

ROCK Ö POP Ö LIVE Ö DANCE Ö TECHNO Ö CLASSIC Ö SOFT Ö OFF Ö ROCK

MUTE FUNCTION

Press the MUTE button once to mute the sound. “MUTE” will appear on the LCD screen. Press

the MUTE button again to restore the sound.

BOOKMARK FEATURE

Storing bookmarks in the memory to be viewed is similar to marking your page in a book. You

can quickly go to any point on the disc.

1. To program bookmarks

• Press the BOOKMARK button during playback until it appears on the screen.

• Use the navigation buttons to go to the empty bookmark space.

• Press the PLAY button to mark the desired section.

• Repeat steps 1 through 3 to program remaining bookmarks.

• Press the BOOKMARK button to exit the bookmark window.

PORTABLE DVD PLAYER V12M12_IM_EN_04232008

- 19 - www.jWIN.com

OPERATIONAL INSTRUCTIONS

BOOKMARK FEATURE-continued

2. To play programmed bookmarks:

• Press the BOOKMARK button to enter the bookmark section.

• Use the navigation buttons to go to your desired bookmark position, and then press the

PLAY button to confirm. The playing time will display on the screen.

• Repeat steps 1 through 2 to play other bookmarked positions.

3. To clear bookmarks:

• In the bookmark section, press the CLEAR button to erase the old bookmark marking.

• Exit the bookmark by pressing the BOOKMARK button, or open the disc compartment

cover to clear all programmed bookmarks.

Note: Some discs may not accept the Bookmark function. 12 bookmarks can be memorized for

each disc.

ZOOM FUNCTION

This player can magnify a picture. Press the ZOOM button to zoom during normal, slow or still

playback mode. Use the navigation buttons to select the desired part of the zoomed picture.

Note: This function only works with DVD and VCD discs.

VIEWING FROM A DIFFERENT CAMERA ANGLE (MULTI-ANGLE)

Some DVD discs may contain scenes which have been shot simultaneously from a number of

different camera angles. This function depends on a disc.

1. Play a DVD disc that is recorded with multiple angles.

2. Press the ANGLE button. If the disc contains different angled views, it will show the movie

with the different angle.

3. To return the normal angled view, press the ANGLE button until the camera icon disappears.

DISPLAY FEATURE

Press the DISPLAY button to show the elapsed and remaining time of the playing disc. Each time

the DISPLAY button is pressed, the time will change on the screen as follows:

• DVD: Title Elapsed Ö Title Remain Ö Chapter Elapsed Ö Chapter Remain Ö Display Off

• VCD & CD: Single Elapsed Ö Single Remain Ö Total Elapsed Ö Total Remain Ö Display Off

• MP3 CD: Single Elapsed Ö Single Remain

PBC (PLAYBACK CONTROL) FUNCTION (VCD2.0 ONLY)

When playing a VCD with PBC function, you can enjoy simple interactive software on the TV

screen. By turning on this function, desired tracks can be selected by pressing the numeric

buttons. This feature is enabled only when a VCD2.0 disc supports the PBC feature. After

selecting a track, press the ENTER button to start playing the selected track.

Page is loading ...

jWIN JD-VD742 User manual

jWIN JD-VD742 User manual

Related papers

Other documents