jWIN JD-VD503 User manual

Brand: jWIN

Model: JD-VD503

Category: DVD players

Type: User manual

This manual is also suitable for

DVD Player JD-VD503

JD-VD503

For attention of parents:

In order to avoid the situation that you forget the parental lock

code and can not enter into the operation of parental lock setting,

here we offer you the super secret code: 1369. You may use this

code to enter into the operation of parental setting. To prevent

the young children from knowing this secret code, please tear the

note from this user's manual and keep in secret place. Thanks.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated "dangerous voltage" within

the product's enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

SAFETY PRECAUTIONS

Thanks for purchasing the jWIN DVD player. Before operating this player, please read

this manual and retain it for future reference.

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

WARNING:

CAUTION:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE.

DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

When replacing the direct plug-in power supply or a separable, cord-connected power supply, the replacement

must be the exact duplicate, or one that has been recommended by the manufacturer.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH THE WIDE BLADE OF THE PLUG TO THE WIDE SLOT,

AND FULLY INSERT.

This DVD player employs a laser system.

Use of controls, adjustments or the performance of procedures other than those specified may result in

hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure.

DO NOT STARE INTO BEAM.

FCC NOTICE:

This equipment has been tested and proved to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

WARNING:

Changes or modifications made to this equipment, not expressly approved by jWIN, or parties

authorized by jWIN, could void the user's authority to operate the equipment.

CAUTION:

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

PLEASE READ THESE INSTRUCTIONS AND KEEP THESE INSTRUCTIONS FOR FUTURE

REFERENCE. PLEASE HEED ALL WARNINGS AND FOLLOW ALL INSTRUCTIONS.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard.

The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing.

This unit is fully transistorized and does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1.Read these instrucitons

After unpacking this product, read these

instructions carefully, and follow all the

instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation

openings. Install in accordance with

the manufacturer's instructions.

10.Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and

the point where they exit from the

apparatus.

11. Only use attachments/accessories

specified by the manufacturer.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

8.Do not install near any heat sources

such as radiators, heat registers, stoves,

or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of

the polarized or grounding-type plug.

A polarized plug has two blades with

one wider than the other. A grounding

type plug has two blades and a third

grounding prong. The wide blade or

the third prong are provided for your

safety. If the provided plug does not

fit into your outlet, consult an

electrician for replacement of the

obsolete outlet.

13. Unplug this apparatus during lightning storms

or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

Notes on Moisture Condensation

Moisture condensation damages the DVD player.

Please read the following carefully.

Moisture condensation occurs during the

following cases.

Do not use the DVD player when moisture

condensation may occur.

Moisture condensation occurs , for example, when you pour

a cold drink into a glass on a warm day. Drops of water form

on the outside of the glass. In the same way, moisture may

condense on the optical pick-up lens inside this unit, one of

the most crucial internal parts of the DVD player.

When you bring the DVD player directly from a cold

place to a warm place.

When you use the DVD player in a room where you

just turned on the heater, or a place where the cold wind

from the air conditioner directly hits the unit.

In summer, when you use the DVD player in a hot and

humid place just after you move the unit from an air

conditioned room.

When you use the DVD player in a humid place.

If you use the DVD player in such a situation , it may

damage discs and internal parts. Remove the disc,connect

the power cord of the DVD player to the wall outlet, turn

on the DVD player, and leave it for two or three hours.

After two or three hours , the DVD player will have

warmed up and evaporated any moisture. Keep the DVD

player connected to the wall outlet and moisture

condensation will seldom occur.

To Obtain a Clear Picture

The DVD player is a high technology, precision device. If the

optical pick-up lens and disc drive parts are dirty or worn down,

the picture quality becomes poor. To obtain a clear picture,

we recommend regular inspection and maintenance (cleaning

or parts replacement ) every 1,000 hours of use depending

on the operating environment. For details, contact your nearest

dealer.

Notes on Positioning

When you place this DVD player near a TV, radio, or VCR,

the playback picture may become poor and the sound may

be distorted. In this case, place the DVD player away from

the TV, radio, or VCR.

Notes on Cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent

solution, wring well and wipe. Use a dry cloth to wipe it dry.

Do not use any type of solvent , such as thinner or benzine,

as they may damage the surface of the DVD player. If you

use a chemical saturated cloth to clean the unit, follow that

product's instructions.

Notes on Handling

When shipping the DVD player, the original shipping carton

and packing materials come in handy . For maximum

protection, repack the unit as it was originally packed at the

factory.

Do not use volatile liquids, such as insect spray, near the

DVD player. Do not leave rubber or plastic products in

contact with the DVD player for a long time. They will

leave marks on the finish.

The top and rear panels of the DVD player may become

warm after a long period of use. This is not a malfunction.

When the DVD player is not in use, be sure to remove

the disc and turn off the power.

If you do not use the DVD player for a long period, the unit

may not function properly in the future.Turn on and use the

DVD player occasionally.

Points For Attention

Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

Dangerous high-voltage parts and Laser are present inside the enclosure. Do not open the cabinet.

Refer servicing to qualified personnel only.

Precautions on Use: DVD players are high-end electric appliances, in which large-scale

integrated circuits and precise laser devices are incorporated. In order to prolong the lifespan of the

appliance, please don't turn on and turn off within a time interval of less than 10 seconds. For the sake

of safety, be sure to cut off the power supply of the appliance before conducting any connections.

Note: The illustrations in this operation instruction may be different from real objects.

Notes on Maintenance

Don't put the appliance in the following places:

* Places exposed to direct sunlight or close to heat

radiating appliances (e.g. heater).

* The top of other heat radiating objects.

* Places with poor ventilation or full of dust.

* Places apt to vibration, rain, moisture, or where

The appliance can not be stably placed.

* Places close to large-powerful loudspeakers or on the same table with loudspeakers so as to avoid vibration,

which may cause malfunction.

* Do not move the appliance from a cold place to a warm one with a sharp temperature difference and the dew

may be condensed on the pick-up head, which is apt to result in the malfunction of the appliance. Take out

the disc and connect the power supply. The appliance will resume its normal working state in 1-2 hours.

* If using the appliance under poor external surroundings for a long time, dust may accumulate on the laser

head. Use a laser head cleaning disc to clean. Please refer to the specifications of the cleaning disc for detail.

* Use a soft cotton cloth with neutral detergent to wipe the appliance. Do not use materials such as sand paper,

alcohol or gasoline, etc.

* Do not use seriously distorted or worn discs in order not to damage disc loading function of the appliance.

~120V/60Hz

Notes on the power supply

* Use proper power supply voltage Voltages other

than the rated value are strictly prohibited.

* Hold the plug tightly when plugging into or pulling

out the AC plug, and do not pull the power cord.

* Please make sure that power cord and other lines

are properly connected before turning on power supply.

* Please turn down the volume of the power amplifier

to the minimum before turning on power supply

and adjust the volume according to the need when starting play in order not to damage the power

amplifier or loudspeaker.

* If you intend not to use the appliance for a long time, please remove the plug of power cord from

the outlet.

Notes on servicing

* Don't open the appliance to repair by yourself. If

there is a problem, please refer servicing to a local

maintenance department.

* Be sure to cut off power supply before removing

the cover to avoid possible electric shock.

* The components with the mark must be replaced

with the ones of the same type and specification.

Operating Interface ------------------------8-10

Front Panel

Back Panel Ports

Remote Control Unit

VFD Display

Reference Guide----------------------------11

Supported Disc Formats-----------------------10

Preparation Before Playing-------------------11-14

Battery Installation for Remote Control

System Connection

Setup of TV Signal System

Basic Operation--------------------------14-20

Turn on The Player

Turn Off

Playing a Disc

NTSC/PAL System

Other Function Buttons----------------------20-25

Stop

Pause/Step

Fast Forward & Fast Rewind

Slow Motion

A-B Repeat

Repeat

Zoom

Return

Title (Applicable Only to DVD)

Direction & Enter

Angle

Screen Display

Clear

3D Surround Sound Effect

Frequency Spectrum

Standby

Spectrum (EQ)

SAFETY PRECAUTIONS--------------------1-2

IMPORTANT SAFETY INSTRUCTIONS---------3-6

How to Set Up System----------------------26-31

General Setup

Audio Setup

Video Setup

Password Setup Page

Preference Setup Page

How to Use Programming Function---------------32

Programmed Play for SVCD, VCD and CD Discs

Programmed Play for DVD Disc

How to Use Search Function----------------- 33-35

For DVD Disc

For SVCD / VCD / CD Disc

How to Play MP3/WMA Discs 36-37

The Structure of MP3/WMA Discs

Directory Structure of MP3/WMA Disc Displayed In

The Player

How to Switch The Directory of MP3/WMA

How to Enter Tracks for Play

--------------

Intelligent Screensaver and Stand-by Function-------41

Malfunction & Troubleshooting----------------41

DVD Introduction and Features---------------42-44

Disc Reference--------------------------44-45

Specification-----------------------------46

TABLE OF CONTENTS

How to Use KARAOKE Function-------------35-36

To Connect Microphone

Start KARAOKE

To Empoly The Special Functions of KARAOKE

How to Enjoy The Digital Album of Picture CD---38-40

Play Mode

Previous Page/Next Page

Pause

Scan Mode Switch

Zoom

Rotation Function

1. OPERATING INTERFACE

BACK PANEL PORTS:

FRONT PANEL:

9. POWER Button

10. Remote Control Signal Sensor

11. MIC Volume Control Knob

12. ECHO Control

13. MIC Jack1

14. MIC Jack2

15. MIC Cover

1. Disc Tray

2. OPEN/CLOSE Button

3. PLAY Button

4. PAUSE Button

5. STOP Button

6. STANDBY Button

7. RETURN Button

8. AUDIO Button

VIDEO

COMPONENT

VIDEO OUT

S-VIDEO

OPTICAL COAXIAL

5.1CH SURROUND

AUDIO OUT

MIXED

AUDIO OUT

REMOTE CONTROL:

1.POWER ON/STANDBY button

2.NTSC/PAL button

3.RECALL button

4.NUMBER button

5.STOP button

6.ZOOM button

7.PLAY button

8.PAUSE button

9.UP button

10.LEFT button

11.DOWN button

12.MENU (PBC) button

13.VOLUME control (-)

14.PREV. button

15.NEXT button

16.TITLE button

17. SLOW MOTION button

18. RETURN button

19. SUBTITLE button

20. button

21. SPECTRUM button

22. PROGRESSIVE button

23. CLEAR button

24. SEARCH button

25. 3D

26. AUDIO button

27. SETUP button

28. RIGHT button

29. ENTER button

30. OSD button

31. VOLUME control (+)

32. FAST FORWARD button

33. FAST REWIND button

34. A-B REPEAT button

35. REPEAT button

36. PROGRAM button

37. ANGL button

38. MUTE button

OPEN/CLOSE

VFD DISPLAY:

2. SUPPORTED DISC FORMATS

<1> Disc Format Display

<2> Title Display

<3> Chapter/Track Display

<4> Playing Display

<5> Repeat Display

<6> Pause Display

<7> Hour Display

<8> Minute Display

<9> Second Display

When playing discs, VFD will be as follows.

3. REFERENCE GUIDE

4. PREPARATION BEFORE PLAYING

4.1 BATTERY INSTALLATION FOR REMOTE

CONTROL

Open the battery compartment lid and insert a pair

of AAA batteries with correct polarity as indicated.

Please point at the remote sensor on the player while

using the remote control.

On playing DVD discs

On playing Super VCD discs

On playing DVCD discs

On playing MP3 discs

On playing Picture CD discs

On playing VCD discs

On playing CD discs

On playing WMA discs

VIDEO

COMPONENT

VIDEO OUT

5.1CH SURROUND

AUDIO OUT

MIXED

AUDIO OUT

4.2 SYSTEM CONNECTION

1. Turn off the power before connection.

2. Turn on the power after finishing connection.

*Wires must be firmly connected; especially the

plug shall be fully inserted.

VIDEO

COMPONENT

VIDEO OUT

S-VIDEO

OPTICAL COAXIAL

5.1CH SURROUND

AUDIO OUT

MIXED

AUDIO OUT

VIDEO

COMPONENT

VIDEO OUT

5.1CH SURROUND

AUDIO OUT

MIXED

AUDIO OUT

1. Normal connection

Connect with TV

Use the YUV cords to connect the player with the

corresponding ports of the TV set as shown in the

picture on the .right

2.Connect with S-Terminal

Connect one end of S-Terminal wire with S-Terminal

output socket on this player back-panel and another

with the S-Terminal input socket of the TV, and then

connect audio wire with the TV.

3.Connect with YUV (Y Cb Cr) Terminal

Connect one end of YUV wire with the Y, Pb/Cb, Pr/Cr

socket on the disc player and another with the corresponding

Y, Pb/Cb, Pr/Cr socket of the TV. And then connect

audio wire with TV. See picture at right.

When you connect the progressive scan TV, press the

PROGRESSIVE button on the remote control and if

no picture displays on the screen after DVD player

loads the discs, switch the video mode of the TV to

progressive scan and obtain the picture.

Notes: For normal TV, if you press the PROGRESSIVE

button on the remote control, no picture displays on

the screen; press PROGRESSIVE button again and

it will shift to interlace scan mode. Then all information

will resume factory settings after pressing the RECALL

button.

Connect with AV power amplifier

1. Normal Connection

The connection method is illustrated in the picture.

2. Connect with AV Amplifier with 5.1

Channel Surround Audio Input.

4.3 SETUP OF TV SIGNAL SYSTEM

If picture is not full screen or edge of the picture

has been covered or TV white-black phenomenon

exists, please press the NTSC/PAL button on the remote

control, adjust the whole player output system

according to TV system.

3. Connect with Optical-Digital Audio

Terminal or Coaxial Terminal.

Directly connect the optical or coaxial cord of the

amplifier with optical or coaxial terminal of this

player (this factory setting mode is SPDIF-PCM ),

then connect video terminal of the player with video

interface of TV.

When using optical or coaxial output function of this

player, please refer to 7.2 Audio setting up for the

detailed setup method.

Note: Pictures are possible to be less than full screen

or partially covered, because DVD discs can support

different picture proportions.

5. BASIC OPERATION

After connection, you must make the following

preparations before operating this player.

1. Switch the TV on and select "video input".

2. Connect the power wires of the player with the

socket.

Notes: When the icon " " displays on the TV screen,

it means that the current operation is invalid probably

resulting from maloperation or restriction of the discs.

OPEN/CLOSE

OPEN

POWER

OFF

Turn on the player

NO DISC

No disc

1.Press the POWER button to switch on the power

then it will load disc as illustrated at right.

Note: Turn the volume of amplifier to the minimum.

If this player has been connected with the amplifier,

then turn the amplifier power on and switch input

channeltoDVD.

Note: If no opening picture or no color shows when

turning on the player, please press NTSC/PAL""

button on the remote control, adjust the whole player

output mode to accord with TV system. Or press

PROGRESSIVE button to set the video output to

proper mode, see 4.3 for detail.

2. Press the OPEN/CLOSE button on the remote

control or on the player.

Turn Off

5.1 PLAYING A DISC

1. PLAY

PLAY

DVD

Type of disc

OPEN/CLOSE

3. Place adisc into thedisc trayandthen pressthe OPEN/

CLOSE button on the remote control or on the player

to close the disc tray. The player can automatically

discern different kinds of discs, and disc information

may be displayed in the left upper corner of TV screen.

Note:The disc tray shall be opened/ closed by pressing

the OPEN/CLOSE button after power on. Do not

push or pull the tray by force so as to avoid damage

to the appliance.

4. After loading, the disc will be played automatically,

or press buttons for other operation.

Press the OPEN/CLOSE button on the remote control""

or the player to open the disc tray, take the disc out,

close the disc tray, and then press the STANDBY button

to standby mode, or press the POWER button to turn

off the player completely.

5. STANDBY

3. PREV (Track or Page)

PRESS PLAY KEY TO CONTINUE

STATEOFMEMORYSTOP

2. STOP

Press STOP once, the player enters memory-stop state;

press again, the player will completely stop.

4. NEXT (Track or Page)

Note: Some discs do not support the functions described

in item 3 and 4 above.

STANDBY

5.2 NTSC/PAL SYSTEM

Continuously press NTSC/PAL on the remote control

to switch the following systems. Adjust the disc player

output mode to match the TV system , either:

MULTI

NTSC

PAL

Note:

1. This player has the function of automatically

discerning the format, and defaults to the NTSC system.

If playing discs in NTSC format, the player can

automatically switch to NTSC system. At this

time, it is normal that the picture will be instantly

flashed.

6. RETURN

RETURN

Back

N/P

2. If the picture is not colorful, the color is abnormal,

or the sound and picture are temporarily interrupted,

(which may be caused by the discrepancy between

the disc format and TV system), at this time, you can

adjust TV system or picture output mode of the whole

disc player by this option to make them compatible.

Directly press NTSC/PAL button on the remote control

to change the system.

Page is loading ...

jWIN JD-VD503 User manual

Brand: jWIN

Model: JD-VD503

Category: DVD players

Type: User manual

This manual is also suitable for

DVD Player JD-VD503

Download PDF

report

jWIN JD-VD503 User manual

This manual is also suitable for

jWIN JD-VD503 User manual

Related papers

Other documents