PR4002
3 70
A2
Max:600x400mm/24x16"
Min:200x100mm /8x4"
MAX:
400mm/16"
MAX:600mm/24"
Yes --- Perfect!
No --- This mount is NOT compatible.
200x100mm/8x4"
600x400mm/24x16"?
M6X30
X4
M-B
M6&M10 Wrench
M8X25
X3
A
Nut
M6
X4
B
Bolt
80X40
X1
C
Plastic Gasket
Steel Gasket
1.5mm
X1
D
4mm Allen Key
5mm Allen Key
Washer
Support Pillar
Support Pillar
TV Bracket
TV Plate
Connecting Plate
Tilt Angle Adjuster
Plastic Cover
Bolt
Tempered Glass Base
X4
X1
H
Foot Pad
X1
I
Safety Lock
X1
I
Wire Clip
X1
I
X2
F
M8X15
X4
M-C
M8X45
X4
M-D
M6X15
X4
M-A
M8X65
X4
M-E
Washer
X4
M-F
Spacer-1
X8
M-G
Spacer-2
X8
M-H
3
4
X1
X1
X1
X1
X1
5
6
7
8
9
10
M6X50
X2
E
Ф16*Ф6*1.5
X2
E
Bolt
Plastic Washer
Ф30*Ф10*1.0
X1
G
Steel Washer
Ф30*Ф10*1.5
X1
G
H
D Steel Gasket
H
H
A
I
I
I
A
Put tempered glass base on the table. Put steel gasket (D) and M8X25 bolt(A) under
tempered glass base .
Turn plastic cover and support pillar upside down under tempered glass base
and then tighten the bolts( A ) with the 5mm allen key( I ).
D
Steel Gasket
5
8
5
5
5
5
M8X25
5mm Allen Key
8
5
5
5
8
5
Connecting the Support Pillar to Tempered Glass Base
C
I
G
Plastic Washer
G Plastic Washer
G Steel Washer
C Plastic Gasket
I Wrench
I Wrench
G
Steel Washer
Connecting the support pillar and plastic gasket( C ) to support pillar by using
bolt ,plastic washer( G ) and steel washer( G ). Please see above figures.
Then tighten the bolt with the wrench( I ).
Connecting the Support Pillar to Support Pillar
2
2
2
9
9
Plastic Gasket
Note:
Arrow should be
on the back of the
support pillar .
9
9
12
1
Step 3 Connecting the TV Plate with Tilt Angle Adjuster
4
7
I Wrench
Connecting the two TV plates by using connecting plate ,tilt angle adjuster
and nuts( B ).Then tighten the nuts( B ) with the wrench( I ).
7
7
6
6
4
4
4
4 6 7
I
B
B
6
F
Note:
Three choices
for height
adjustment
Connecting TV plate to support pillar by
using bolts( E ) and washers( E ).
Then tighten the bolts( E ) with 4mm allen key( I ).
Attaching wire clips( F ) into the holes.
I
4mm Allen Key
I
4mm Allen Key
Step 4
E
4.3
4.2
4.1
E Bolt
E Washer
E
2
2
2
2
2
M6X50
Ф16*Ф6*1.5
Choose the appropriate position (three options)
Hang the TV plate onto the support pillar .
F
7
Thread screws by hand into the threaded holes
on the back of your TV to select which screw
diameter fits your TV.
5-1
5-2
Choose the appropriate
length screws for your TV.
Choose the appropriate quantity spacers for your TV.
May be 0~4pcs. Alternate spacers setup below:
M-C/M-D/M-E
M-G/M-H
M-A/M-B
Top
M-F
Spacer-1
X8
M-G
Spacer-2
X8
M-H
Step 5
Step 6
3
3
3
3
8
Choose TV Screws and Spacers
Choose the appropriate position (three options)
for your TV.
Hang the TV bracket onto the TV plate .
Put the safety lock in place and fasten the
fixing screw to the TV plate securely.
F
F
Step 7
10
3
3
10
10
9
Step 8
10
Adjustments
8-1 Tilting angle adjustment (0°/+5°)
8-2 Swivel tightness adjustment
8-1-1Loosen 2 tilting bolts showing below figures by 1-2 turns.
8-1-2 Hold the TV with your hands,Adjust TV to your desired angle.
8-1-3 Tighten 2 tilting bolts with 5mm allen key( I ).
8-1-4 Move your hands away.
Refer to below illustrations to adjust the level of swivel tightness
by wrench( I ).
I
5mm Allen Key
I
5mm Allen Key
Tilting bolt
Tilting bolt
I
Wrench
+
-
+5°
+5°
0°
0°
Product dimension:
11
+5°
0°
+25°/-25
°
12
/
