Ancona AN-4251 Installation guide

Ancona
Brand
Ancona
Model
AN-4251
Type
Installation guide

This manual is also suitable for

© ®
Single Handle Pull-out Kitchen Faucet
STANDARDS
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
Attention:
Helpful Information
Important
Eliya
2020-07-02 MAAN4251-1
SEALED-TUBE
tools for future use!
1.8 gpm/6.8 L/min
2
3
Installation size map
4.9 in. (12.6 cm)
7.2 in.
(18.4 cm)
17.2 in.
(43.7 cm)
10.3 in. (26.4 cm)
11.5 in. (29.2 cm)
9 in. (23 cm)
9.2 in.
(23.4 cm)
Faucet Installation
Faucet Installation
Remove the rubber, metal washers
and mounting nut from the base by
hand twisting it off.
For 1-hole installation, insert the
faucet through the hole on the sink.
For 3-hole installation, insert the
faucet to the base plate and then
through the hole on the sink.
Note: Make sure that the rubber o-ring
stays above the mounting surface for
1-hole installation or between the
faucet and base plate for 3-hole
installation.
1
Make sure sink installation hole is
1 ³⁄8 inches (3.5 cm).
Rubber
o-ring
Rubber
o-ring
Base
plate
2.4 in. (6.2 cm)
3.5 cm
(1 ⁄ in.)
4
5
6
Secure the faucet by firmly hand
tightening the rubber washer, metal
washer and mounting nut back on the
faucet threads underneath the sink.
Tighten the screws on the mounting
nut with a Phillips screwdriver.
Connect the water supply lines to the
hot and cold water valves. Tighten
with an adjustable wrench. Do not
overtighten.
7
Install the spray hose to the outlet
hoses. The outlet will connect with a
simple push. Then attach the weight to
the middle of the spray hose.
Turn the water valves back on and
then turn on the faucet. Run the water
flow for 15 seconds to clean up the
lines and check for any leaks.
The faucet should be flushed for
possible debris prior to using. Remove
the nozzle head by hand twisting it off.
Turn the faucet handle all the way on,
turn on the hot and cold water supply
and flush water lines for one minute.
Re-install the nozzle head by hand
twisting back on.
Attention: Make sure that the inlet
hoses are not twisted.
Cold
supply
hose.
Hot
supply
hose.
Push
A.
B. Turn on water supplies. Check connections for leaks.
C. Remove hand shower and let both hot and cold water
run for one minute. This will help clean any debris that
might otherwise clog the system. Replace hand shower.
D. Operate handle up and down, in cold and hot positions,
to flush water lines thoroughly.
Test Faucet Installation
Simply rinse the surface with clear water or
mild liquid detergents
if necessary Dry the
faucet withaclean soft cotton cloth
Do not
use any cleaning agents containing
acids
polish abrasives or harsh cleaners
Maintenance:
1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Parts list
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
NO. PART NAME
Index1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Screw
Handle
Trim cap
Screw nut
Cartridge
Cartridge sleeve
Allen key
Weight
Quick connect base
Deck plate
Deck plate(baseboard)
Spout
Swivel connector
Anticlastic ring
Body
Cartridge base
Sleeve connector
Thread sleeve
O-ring
Washer
Gasket
Screw nut
Screw
Pull-out sleeve
Shower sleeve
Spray head
Aerator wrench
Inlet pipe
Supply line
Single valve
Quick connect components
31
32
Supply line
Pull out hose
33
34
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Ancona AN-4251 Installation guide

Ancona
Brand
Ancona
Model
AN-4251
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents