Westinghouse 5223000 Owner's manual

Westinghouse
Brand
Westinghouse
Model
5223000
Type
Owner's manual

Westinghouse 5223000 is a versatile LED retrofit kit that can be used in three different applications: high bay, post top, and shoe box. It is suitable for use in enclosed luminaires with minimum lamp compartment dimensions of 7- 7/8 in (L) x 7- 7/8 in (W) (200mm (L) x 200mm (W)).

The kit is easy to install, requiring only a few simple steps. Simply disconnect the power from the luminaire, remove the existing lamp, disconnect and remove the existing ballast, capacitor, and ignitor, connect the Line wire to the center contact of the lamp holder, connect the Neutral wire to the shell of the lamp holder, close the wiring compartment, insert and screw in the LED Retrofit lamp into the lamp holder, then adjust the angle of the panel according to the application scenario.

Westinghouse 5223000 is a versatile LED retrofit kit that can be used in three different applications: high bay, post top, and shoe box. It is suitable for use in enclosed luminaires with minimum lamp compartment dimensions of 7- 7/8 in (L) x 7- 7/8 in (W) (200mm (L) x 200mm (W)).

The kit is easy to install, requiring only a few simple steps. Simply disconnect the power from the luminaire, remove the existing lamp, disconnect and remove the existing ballast, capacitor, and ignitor, connect the Line wire to the center contact of the lamp holder, connect the Neutral wire to the shell of the lamp holder, close the wiring compartment, insert and screw in the LED Retrofit lamp into the lamp holder, then adjust the angle of the panel according to the application scenario.

INSTALLATION AND SAFETY INSTRUCTIONS
ESF-WH-072
1
2. WIRING DIAGRAMS:
L
N
Replacing Self Ballasted CFL Lamp
L
N
Self ballasted
CFL Lamp
LED Retrofit
lamp
HPS / HID
lamp
Ballast
Ignitor
Capacitor
L
N
Replacing
with
Replacing
with
L
N
Ballast
Ignitor
Capacitor
Replacing HPS/HID Lamp
Self Ballasted CFL Wiring Diagram
LED Retrofit Lamp Wiring Diagram
LED Retrofit Lamp Wiring Diagram
HPS/HID Wiring Diagram
1. CAUTIONS:
WARNING: Operating temperature: -22°F to 140°F (-30°C to 60°C).
WARNING: These LED Lamps require all ballasts, capacitors, and ignitors to be bypassed or removed. Do not operate lamps on existing ballasts.
WARNING: Risk of re or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrot kit. Check
for enclosed wiring and components.
WARNING: Risk of re or electric shock. LED Retrot kit installation requires knowledge of luminaires electrical systems. If not qualied, do not
attempt installation. Contact a qualied electrician.
WARNING: When used in portable table luminaires, ensure the distance from the bottom of the base to the top of the lampholder does not exceed
three (3) times the base diameter.
SUITABLE FOR USE IN ENCLOSED LUMINAIRES, MINIMUM LAMP COMPARTMENT DIMENSIONS OF 7- 7/8 in (L) x 7- 7/8 in (W) (200mm (L) x 200mm (W)).
WARNING: Do not make or alter any open holes in an enclosure of wiring or electrical component during kit installation.
WARNING: Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead
installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by
employing applicable connectors.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
WARNING: Risk of re or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photo-
graphs and/or drawings and where the input rating of the retrot kit does not exceed the input rating of the luminaire.
THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.
ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE-STANDING PORTABLE LUMINAIRE.
USE ONLY WITH A PORTABLE LUMINAIRE THAT IS PROVIDED WITH A SHADE.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY
AUTHORITIES HAVING JURISDICTION.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the
product and the hazards involved or equivalent.
ESF-WH-0722
3. FIXTURE WIRING INSTRUCTION:
STEP 1: Disconnect power from the luminaire and follow proper lockout/tagout procedures before beginning installation or maintenance.
STEP 2: Remove the existing lamp. Dispose of the lamps per local equirements.
STEP 3: Disconnect and remove the existing ballast, capacitor, and ignitor. Dispose of the components per local requirements.
STEP 4: Connect the Line wire (Line/Hot) to the center contact (eyelet) of the lamp holder.
STEP 5: Connect the Neutral wire (Common) to the shell of the lamp holder.
STEP 6: Close the wiring compartment. Make sure the wires are not pinched, bound, or crimped when closing the compartment.
STEP 7: Insert and screw in the LED Retrot lamp into the lamp holder, then adjust the angle of the panel according to the application scenario.
STEP 8: Switch on the power.
4. Application (One lamp for three applications)
5. This products can be used with 0-10V dimmers and sensors. You can choose additional accessories shown below to t your requirement.
Note: Plug the cable or sensor into the lamp's connection socket. Please use
the adapter to connect the sensor when the lamp is installed horizontally. The
detailed wiring and setting of the accessories, please refer to the correspond-
ing manual of each item.
Shoe box
High bay Post top
, Westinghouse, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting. All Rights Reserved.
Item number Description Product
522306930 Three in one dimming cable
522306916 Photocell+PIR Sensor
522306917 Daylight Sensor
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Westinghouse 5223000 Owner's manual

Westinghouse
Brand
Westinghouse
Model
5223000
Type
Owner's manual

Westinghouse 5223000 is a versatile LED retrofit kit that can be used in three different applications: high bay, post top, and shoe box. It is suitable for use in enclosed luminaires with minimum lamp compartment dimensions of 7- 7/8 in (L) x 7- 7/8 in (W) (200mm (L) x 200mm (W)).

The kit is easy to install, requiring only a few simple steps. Simply disconnect the power from the luminaire, remove the existing lamp, disconnect and remove the existing ballast, capacitor, and ignitor, connect the Line wire to the center contact of the lamp holder, connect the Neutral wire to the shell of the lamp holder, close the wiring compartment, insert and screw in the LED Retrofit lamp into the lamp holder, then adjust the angle of the panel according to the application scenario.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents