Page is loading ...
20072-000
WALL SCONCE
Read and Save:
LIGHT BULB REPLACEMENT
1. Uses one 60 watt type A bulb or CFL or LED equivalent. Integrated LED replacement not required.
2. DO NOT EXCEED RECOMMENDED WATTAGE.
3. Turn off the unit and allow the bulb to cool before touching.
4. Light bulb should never touch the lamp shade.
CLEANING AND MAINTENANCE
1. Clean using a mild cleaning solution and a soft cloth.
2. Never use a rough cloth or chemical cleaners containing acids, abrasives or solvents.
1. This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric
shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully inserted. Do not alter the
plug.
2. Do not install non-factory wiring or any other electrical components. Altering or modifying the lamp in any way will render the
product unsafe.
3. Keep curtains, shades, wall hangings and all other fabrics and objects away from the lamp, lamp switch and light bulb.
Lamps are not designed to support additional weight.
4. This lamp is approved for indoor use only.
5. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment on and off, the user isencouraged to try to correct the interfer-
ence by one or more of the following:
- Reorient or relocate the receiving antenna.
- Increase the separation between the lighting unit and receiver.
- Connect the lighting unit into an outlet on a circuit other than the outlet which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
NOTE: Please note that changes and modifcations not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Tools required for assembly (not included)
Tape measure, pencil, drill, step ladder, hammer.
IMPORTANT SAFETY INSTRUCTIONS
For Customer Assistance:
www.evolutionlightingllc.com
Made In China
Installation
1
Assembling the lamp
2
Installing the mounting hardware
3
Installing the xture
4
Installing the shade and light bulb
Place the shade (C) over the socket on the xture assembly (A).
Install a 60 Watt Type A Bulb or CFL or LED equivalent (not included).
Carefully unpack and lay all parts on a clean, level surface.
Assemble all tubes (B) to the xture assembly (A).
2.75in/7cm
BB
AA
Determine the desired location of the xture making sure
you have access to an electrical outlet and there are no
electrical lines or plumbing where you intend to attach the
mounting hardware.
Mark the anchor (AA) locations on wall and drill each hole 6 mm
in diameter.
Insert the anchors (AA) and tap into the wall until secure.
Set two screws (BB) into the top anchors (AA) using a screwdriver,
leaving enough exposed to set into the keyhole slots on the xture
assembly.
Align the keyhole slots on the xture assembly (A) with the
screws (BB) on wall and then gently push the canopy toward the
wall and slide down until secure.
Attach the plastic clip (CC) to the appropriate location on the
bottom tube (B) and mark the outside edge of the plastic
clip (CC). Unthread the bottom tube (B) and move it away, drill a
hole 6 mm in diameter at the center of this marked location and
install the anchor (AA). Remove the pre-attached plastic clip (CC)
from the bottom tube (B) and secure it to the anchor (AA) with
the short screw (DD).
Slide the bottom tube (B) through the plastic clip (CC) and thread
it to the assembled tubes.
/
