Legrand Mighty Mo 6E 2-Post Channel Racks, Mounting Installation guide

Type
Installation guide

This manual is also suitable for

NO. 3 PHILLIPS HEAD
DRIVER BIT
1/2" NUT DRIVER
CORDLESS DRILL
WITH ADJUSTABLE
TORQUE SETTING OR
SAE SOCKET SET
FOR THIS
INSTALLATION, THE
FOLLOWING TOOLS
ARE REQUIRED:
MANAGEMENT MM6E
QTY. 6
(7FT & 8FT KIT)
QTY. 12
(7FT & 8FT KIT)
QTY. 4
(7FT & 8FT KIT)
QTY. 2
(8FT KIT)
QTY. 2
(7FT KIT)
1/4"-20, 3/8" LONG
SCREW WITH
EXTERNAL TOOTH
LOCK WASHER
5/16"-12, 1/2"
LONG THREAD
FORMING SCREW
UNIVERSAL LOWER
BRACKET, "Q-SERIES"
VERTICAL MANAGEMENT
MM6E ATTACHMENT
UNIVERSAL TOP BRACKET,
8FT "Q-SERIES" VERTICAL
MANAGEMENT MM6E
ATTACHMENT
UNIVERSAL TOP BRACKET,
7FT "Q-SERIES" VERTICAL
ATTACHMENT
TITLE:
INSTRUCTION SHEET #: REV: ECN #: SHEET: DWN BY: DATE: CHK BY: DATE: APP. BY: DATE:
MOUNTING INSTRUCTIONS
Q-SERIES VERTICAL MANAGER
TO MM6E RACKING SYSTEM
OR-71601930 01 05111 1 of 6 JPS
1/27/2017
JQ 2/17/2017 CV 2/17/2017
WWW.LEGRAND.US
6.50
.13
2.50
PRIOR TO ASSEMBLY:
INSPECT ALL PACKAGING FOR DAMAGE.1.
REPORT ANY DAMAGE TO THE SHIPPER FOR POTENTIAL REIMBURSEMENT.2.
UNPACK MOUNTING KIT AND INSPECT CONTENTS FOR DAMAGE AND 3.
CORRECT QUANTITIES (USE THE FOLLOWING TABLE FOR REFERENCE).
PRIOR TO INSTALLATION OF THE MOUNTING KIT, ENSURE THAT THE VERTICAL CABLE MANAGER IS ASSEMBLED
AS SHOWN IN THE INSTRUCTION SHEET 71601933.
VERIFY THAT THE MM6 RACKS ARE SQUARE, PLUMB AND SPACED ACCORDING TO THE RACK INSTALLATION
INSTRUCTIONS. INSTRUCTIONS WILL ACCOMMODATE 4 INCH, 6 INCH, 10 INCH OR 12 INCH WIDE Q-SERIES
VERTICAL CABLE MANAGERS.
RACK TO RACK SPACING
8.50
STEP 1:
INSTALL THE UNIVERSAL TOP BRACKETS AT THE TOP OF THE RACKING SYSTEM USING TWO OF THE PROVIDED
THREAD FORMING SCREWS PER BRACKET. FOR A 7 FT RACKING SYSTEM, THE TOP OF THE BRACKET WILL ALIGN
WITH U-HEIGHT MARKING NUMBER 45. FOR AN 8 FT RACKING SYSTEM, THE TOP OF THE BRACKET WILL ALIGN WITH
U-HEIGHT MARKING NUMBER 51. REFER TO THE PICTURES BELOW FOR THE CORRECT ORIENTATION.
8 FOOT RACK
KIT# 60401477
7 FOOT RACK
KIT # 60401478
USE TOP TWO
BRACKET
HOLES IN (4)
HOLE PATTERN
TYPICAL (4)
HOLE MOUNTING
PATTERN
TITLE:
INSTRUCTION SHEET #: REV: ECN #: SHEET:
MOUNTING INSTRUCTIONS
Q-SERIES VERTICAL MANAGER
TO MM6E RACKING SYSTEM
OR-71601930 01 05111 2 of 6
WWW.LEGRAND.US
USE TOP TWO
BRACKET
HOLES IN (4)
HOLE PATTERN
TITLE:
INSTRUCTION SHEET #: REV: ECN #: SHEET:
MOUNTING INSTRUCTIONS
Q-SERIES VERTICAL MANAGER
TO MM6E RACKING SYSTEM
OR-71601930 01 05111 3 of 6
WWW.LEGRAND.US
USE BOTTOM
TWO BRACKET
HOLES IN (4)
HOLE PATTERN
FOR BOTH 7FT
AND 8FT RACKS
TYPICAL (4)
HOLE MOUNTING
PATTERN
STEP 2:
INSTALL THE UNIVERSAL LOWER BRACKETS ON THE MIDDLE OF THE RACKING SYSTEM USING TWO OF THE PROVIDED
THREAD FORMING SCREWS PER BRACKET. FOR BOTH 7FT AND 8FT RACKING SYSTEMS, THE TOP OF THE BRACKET WILL
ALIGN WITH U-HEIGHT MARKING NUMBER 26. REFER TO THE PICTURES BELOW FOR THE CORRECT ORIENTATION.
8 FOOT RACK
KIT# 60401477
7 FOOT RACK
KIT# 60401478
STEP 3:
INSTALL THE UNIVERSAL LOWER BRACKETS ON THE BOTTOM OF THE RACKING SYSTEM USING TWO OF THE
PROVIDED THREAD FORMING SCREWS PER BRACKET. FOR BOTH 7FT AND 8FT RACKING SYSTEMS, THE TOP OF THE
BRACKET WILL ALIGN WITH U-HEIGHT MARKING NUMBER 2. REFER TO THE PICTURES BELOW FOR THE CORRECT
ORIENTATION.
USE BOTTOM
TWO BRACKET
HOLES IN (4)
HOLE PATTERN
FOR BOTH 7FT
AND 8FT RACKS
STEP 4:
TO INSTALL THE VERTICAL MANAGER ONTO THE 7FT AND 8FT RACKING SYSTEMS, THREAD THE PROVIDED 1/4"-20
SCREW TWO FULL TURNS INTO THE SECOND THREADED INSERT DOWN FROM THE TOP OF THE FINGER SECTION.
REFER TO THE PICTURES BELOW FOR CORRECT SCREW SELECTION AND LOCATION. PERFORM THIS STEP ON BOTH
SIDES OF THE VERTICAL MANAGER.
REMINDER: Q-SERIES VERTICAL MANAGER SHOULD BE ASSEMBLED AS OUTLINED IN MM6E SECTION OF
INSTALLATION MANUAL 71601933
TWO FULL
ROTATIONS
TITLE:
INSTRUCTION SHEET #: REV: ECN #: SHEET:
MOUNTING INSTRUCTIONS
Q-SERIES VERTICAL MANAGER
TO MM6E RACKING SYSTEM
OR-71601930 01 05111 4 of 6
WWW.LEGRAND.US
TITLE:
INSTRUCTION SHEET #: REV: ECN #: SHEET:
MOUNTING INSTRUCTIONS
Q-SERIES VERTICAL MANAGER
TO MM6E RACKING SYSTEM
OR-71601930 01 05111 5 of 6
WWW.LEGRAND.US
STEP 5:
FOR BOTH THE 7FT AND 8FT RACKING SYSTEM, LIFT THE VERTICAL MANAGER INTO POSITION BY ALIGNING THE
SCREWS INSTALLED IN STEP 4 WITH THE OPENINGS IN THE TOP BRACKETS AND LOWER IT INTO THE SLOTS AS SHOWN
IN THE PICTURE BELOW. (WATERFALLS AND WATERFALL EXTENSION REMOVED FOR CLARITY)
BE SURE THAT THE LOCK
WASHER IS INSTALLED ON
THE OUTSIDE OF THE BRACKET
STEP 6:
USING THE SAME SCREW USED IN STEP 4, SCREW THE VERTICAL MANAGER TO THE BRACKETS AS SHOWN IN THE
PICTURES BELOW, STARTING WITH THE BOTTOM BRACKET. DO NOT FULLY TIGHTEN THE SCREWS UNTIL ALL BRACKETS
ARE ALIGNED. REPEAT THIS STEP FOR BOTH SIDES OF THE VERTICAL MANAGER.
STEP 7:
TIGHTEN MOUNTING HARDWARE TO A MAXIMUM OF 5 FT-LBS TO ENSURE STABILITY OF ASSEMBLY.
INSTALLATION IS NOW COMPLETE.
TITLE:
INSTRUCTION SHEET #: REV: ECN #: SHEET:
MOUNTING INSTRUCTIONS
Q-SERIES VERTICAL MANAGER
TO MM6E RACKING SYSTEM
OR-71601930 01 05111 6 of 6
WWW.LEGRAND.US
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Legrand Mighty Mo 6E 2-Post Channel Racks, Mounting Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI