Lopi 33 DVI Gas Fireplace Insert User manual

Lopi
Brand
Lopi
Model
33 DVI Gas Fireplace Insert
Type
User manual

This manual is also suitable for

Lopi 33 DVI Gas Fireplace Insert is a versatile heating solution that offers both ambiance and warmth. It features variable flame height adjustment for customized heat output and a realistic log set that enhances its visual appeal. The included remote control allows for convenient operation, and the optional blower helps circulate warm air throughout your space. Moreover, the face design includes a convenient on/off switch and a rheostat for precise flame adjustment. For safety, the insert includes an ODS (Oxygen Depletion Sensor) system and a flame-sensing thermocouple.

Lopi 33 DVI Gas Fireplace Insert is a versatile heating solution that offers both ambiance and warmth. It features variable flame height adjustment for customized heat output and a realistic log set that enhances its visual appeal. The included remote control allows for convenient operation, and the optional blower helps circulate warm air throughout your space. Moreover, the face design includes a convenient on/off switch and a rheostat for precise flame adjustment. For safety, the insert includes an ODS (Oxygen Depletion Sensor) system and a flame-sensing thermocouple.

DVL Universal No Panel Face With Screen (2014)
Small 95100057 Large 95100058
Page 1 of 2 17601849 - 5/24/18 © Travis Industries, Inc.
Compatibility:
• DVL Insert
• 33 DVI Insert
Packing List:
• Face
• (4) 8-32 Nuts
• Left & Right Mounting Brackets
Sizing:
Width Height
Small (95100057) 40” 27”
Large (95100058) 44” 33-1/2”
NOTE: Surround Panels are Not Required - If Using Panels Use Standard Position
The new 2014 surround panels (1 or 3-piece) have two sets of holes/slots to accommodate the new faces that include
screens. The extended position is not used for this face – make sure to use the standard position (see the illustrations
below). Older, pre-2014 panels work for this face as well (those panels were standard position only).
3-Piece Panels
1-Piece Panel
Installation of the Rheostat and On/Off Switch (33 DVI Only)
When using this face you may install the on/off switch on the face (see instructions below) or on the control
panel (see manual). The rheostat must be installed on the control panel. See the directions below for details.
WARNING: Make sure to unplug the heater before installing the rheostat.
Make sure the wires leading to the on/off switch are firmly attached (they attach to the top and bottom posts
on either side of the switch -it does not matter which wire is on top). Route the on/off switch to the slot on the
upper right of the face (you will need to remove the lock-tie on the wiring harness). Remove the knock-out
and slide the switch into the rectangular slot until it locks into place.
Remove the knob and nut from the rheostat. Insert the shaft on the rheostat through the circular hole on the
control panel and secure with the nut. Replace the knob.
Extended
Position
Standard
Position
Standard
Position
Extended
Position
Upper Right of Face
Control Panel
(next to gas control valve)
DVL Universal No Panel Face With Screen (2014)
Small 95100057 Large 95100058
Page 2 of 2 17601849 - 5/24/18 © Travis Industries, Inc.
Installation
WARNING: Turn off gas to the appliance and make sure it is fully cool prior to service.
HINT: The insert should be in place with the gas line, vent, and electrical line attached.
You may pull the insert out slightly for better access.
NOTE: If using surround panels, install them before
attaching the face.
1 Attach the face brackets to the face with the included
nuts (see illustration to the right).
2 The face mounts to the insert as shown in the
illustration below.
Tilt the face back and insert the bottom brackets
into the lower slots until they lock in place.
Lift and rotate the face forward until the
top brackets lock into the upper slots.
b
a
Optional Knock-Out
for Power Cord
(both sides)
  • Page 1 1
  • Page 2 2

Lopi 33 DVI Gas Fireplace Insert User manual

Lopi
Brand
Lopi
Model
33 DVI Gas Fireplace Insert
Type
User manual
This manual is also suitable for

Lopi 33 DVI Gas Fireplace Insert is a versatile heating solution that offers both ambiance and warmth. It features variable flame height adjustment for customized heat output and a realistic log set that enhances its visual appeal. The included remote control allows for convenient operation, and the optional blower helps circulate warm air throughout your space. Moreover, the face design includes a convenient on/off switch and a rheostat for precise flame adjustment. For safety, the insert includes an ODS (Oxygen Depletion Sensor) system and a flame-sensing thermocouple.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents