Lopi 32 DVS Gas Fireplace Insert Operating instructions

Lopi
Brand
Lopi
Model
32 DVS Gas Fireplace Insert
Category
Fireplaces
Type
Operating instructions
Arched Panels - DVS
Black Trim 98500605
© Travis Industries, Inc. 17601062 - 3/26/14 Page 1 of 2
COMPATIBILITY
• DVS Insert (31 DVI, DVS GSR)
PACKING LIST
• Top & Side Panels • Four 10-24 Self-Threading Screws • Double-Back Tape • Trim (w hardware)
Arched Faces with Screens (2014 or later) Require Use of the Extended Position Holes
This surround panel has 2 sets of holes. Hole position is
determined by the face being used (see below)
Standard Position – used for all faces except for the new
2014 arched faces with screens. All other faces use the
standard position hole. If you are uncertain, use the standa
r
position.
Extended Position – used only for new arched faces with
screens (2014 or later). The extended position allows room
the screen and eliminates the ½” gap to the panel. The
extended position hole positions the insert ½” farther into th
e
fireplace cavity.
Extended
Position
Standard
Position
DVS Side
Panel
DVL Side
Panel
PANEL SIZING
40-5/16”
27”
Radius = 40-7/8”
28-7/8”
23-1/2”
Arched Panel Coverage (with trim)
If the Fireplace
Opening Is:
The Panels Will
Cover Up to:
39-3/8” Wide
38-3/8” Wide
37-3/8” Wide
36-3/8” Wide
35-3/8” Wide
34-3/8” Wide
33-3/8” Wide
32-3/8” Wide
31-3/8” Wide
30-3/8” Wide (min.)
23-1/2” Tall
23-3/4” Tall
24” Tall
24-5/16” Tall
24-1/2” Tall
24-3/4” Tall
25” Tall
25-1/4” Tall
25-7/16” Tall
25-5/8” Tall
INSTALLATION INSTRUCTIONS
! Turn the gas source off
prior to installing.
1 With the gas line and
vent attached, install
the side panels (see the
illustration to the right).
Line up each side surround
panel and insert two screws from
the inside to secure in place.
5/16" Nutdriver
Pre-thread the holes on the brackets
screws included in the surround panel kit.
b
a
Run the power cord to
the side of the insert.
Arched Panels - DVS
Black Trim 98500605
© Travis Industries, Inc. 17601062 - 3/26/14 Page 2 of 2
2 Install the top panel and trim. Attach double-back tape to the bottom of the trim to keep it in place.
Double-Back Tape
Install the top panel so the
two tabs insert into the slots
on the side panels.
"L" Bracket
Right Side Trim
Construct the panel trim. Insert one leg of each "L"
bracket into the top and side trim piece as shown
below.
NOTE: The “L” bracket must be installed as
shown - make sure the set screw may be tightened
from behind (remove and re-install if necessary).
Align the trim to form a precise corner, then tighten
the two set screws with a small standard
screwdriver. Slide the trim over the panels.
Tighten the set
screws from the back
side with a small
standard screwdriver
b
Slot for on/off
switch and hole
for rheostat
a
Top Panel
Top Trim
"L" Bracket
Right Side
Trim
Top Trim
31 DVI – On/Off Switch and Rheostat Placement
c
a
Disconnect the red and brown wires leading to the on/off switch. Insert the
wires through the rectangular mounting hole (on the surround panel or
control panel) and attach to the on/off switch. The wires must attach to the
top and bottom posts on either side of the switch -it does not matter which
wire is on top. Press the switch into the rectangular hole until it locks into
place.
WARNING:
Make sure the heater is unplugged
before installing the rheostat.
Upper Right of Trim
Remove the knob and nut from the rheostat (the knob is
held in place with a set screw). Insert the shaft on the
rheostat through the circular hole (on the surround panel
or control panel). Secure with the nut. Replace the knob.
Make sure the wires do not contact the burner pan or
other hot surfaces (secure with lock ties if necessary).
Control Panel
(next to gas control valve)
b
Micro (1/16”)
Standard
Screwdriver
Micro (1/16”)
Standard
Screwdriver
OPTION A OPTION B
  • Page 1 1
  • Page 2 2

Lopi 32 DVS Gas Fireplace Insert Operating instructions

Lopi
Brand
Lopi
Model
32 DVS Gas Fireplace Insert
Category
Fireplaces
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents