Lopi 32 DVS Gas Fireplace Insert User manual

Lopi
Brand
Lopi
Model
32 DVS Gas Fireplace Insert
Type
User manual
DVS Universal No Panel Face With Screen (2014)
Small 95100052 Large 95100053
Page 1 of 3 17601851 - 8/19/14 © Travis Industries, Inc.
Compatibility:
• DVS Insert
• 31 DVI Insert
Packing List:
• Face
• (2) Insert Brackets
• (2) Face Brackets
• (4) 10-24 x ½” Screws
• (4) 8-32 Nuts
Sizing:
Width Height
Small (95100052) 37” 23”
Large (95100053) 40” 29”
NOTE: Surround Panels are Not Required - If Using Panels Use Standard Position
The new 2014 surround panels (1 or 3-piece) have two sets of holes/slots to accommodate the new faces that include
screens. The extended position is not used for this face – make sure to use the standard position (see the illustrations
below). Older, pre-2014 panels work for this face as well (those panels were standard position only).
3-Piece Panels
1-Piece Panel
Installation of the Rheostat and On/Off Switch (31 DVI Only)
When using this face you may install the on/off switch on the face (see instructions below) or on the control
panel (see manual). The rheostat must be installed on the control panel. See the directions below for details.
WARNING: Make sure to unplug the heater before installing the rheostat.
Make sure the wires leading to the on/off switch are firmly attached (they attach to the top and bottom posts
on either side of the switch -it does not matter which wire is on top). Route the on/off switch to the slot on the
upper right of the face (you will need to remove the lock-tie on the wiring harness). Remove the knock-out
and slide the switch into the rectangular slot until it locks into place.
Remove the knob and nut from the rheostat. Insert the shaft on the rheostat through the circular hole on the
control panel and secure with the nut. Replace the knob.
Extended
Position
Standard
Position
Standard
Position
Extended
Position
Upper Right of Face
Control Panel
(next to gas control valve)
DVS Universal No Panel Face With Screen (2014)
Small 95100052 Large 95100053
Page 2 of 3 17601851 - 8/19/14 © Travis Industries, Inc.
Installation
WARNING: Turn off gas to the appliance and make sure it is fully cool prior to service.
HINT: The insert should be in place with the gas line, vent, and electrical line attached. You may pull the
insert out slightly for better access.
1 Remove the glass (see the owner’s manual).
2 If using surround panels, install them at this time.
3 Install the insert brackets following the directions below.
4 Replace the glass (see owner’s manual).
5 Attach the face brackets to the face with the included nuts (see illustration below).
Attach the insert brackets to the
insert with the included screws.
HINT: pre-thread the holes on the
insert before installing the
brackets.
DVS Universal No Panel Face With Screen (2014)
Small 95100052 Large 95100053
Page 3 of 3 17601851 - 8/19/14 © Travis Industries, Inc.
6 The face mounts to the brackets as shown in the illustration below.
Tilt the face back and insert the bottom brackets
into the lower slots until they lock in place.
Lift and rotate the face forward until the
top brackets lock into the upper slots.
b
a
Optional Knock-Out
for Power Cord
(both sides)
  • Page 1 1
  • Page 2 2
  • Page 3 3

Lopi 32 DVS Gas Fireplace Insert User manual

Lopi
Brand
Lopi
Model
32 DVS Gas Fireplace Insert
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents