AE B44.3 Factory Team User manual

1

2

1

2

:: Introduction

:: KIT Features

:: Other Helpful Items

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and

maintaining your new RC10 B44.3. Please take a moment to read through this manual to help familiarize yourself with these

steps.

We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the

illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these

sheets before you start to build.

The RC10B44 has created a winning legacy with three I.F.M.A.R. World Championships, four R.O.A.R. National titles, and

countless regional wins to its credit! Since winning the 2013 I.F.M.A.R. World Championships, the designers behind the doors of

Area 51 set out to further improve the B44 and take it to an even higher level of performance.

Enter the RC10B44.3 Factory Team Kit, the latest evolution of Team Associated’s 1:10 4WD electric off road competition buggy.

The most significant changes are found on the new hard-anodized aluminum chassis, which helps lower the center of gravity to

improve handling and durability. The chassis has been designed to have symmetrical torsional flex to improve handling

consistency — the new floating motor mount, floating servo mount, and chassis machining help to provide the desired flex

symmetry.

Power and traction have continued to improve, so the B44.3’s drivetrain has been built up and refined to keep up with the

demand of today’s high-traction off-road tracks. A set of four precision CVA’s transfer the power from the gear differentials via

ball bearings throughout the car.

Now the B44.3 is even more adaptable to multiple racing conditions with the adjustable weight bias feature. Weight bias can be

significantly altered by using either the front motor configuration with a saddle pack or the rear motor configuration with a shorty

pack. The B44.3 is also backwards compatible with the previous generation VTS slipper clutch (not included) and ball differentials

(not included), making the B44.3 extremely versatile and adaptable to any track condition.

Factory Team V2 12mm big bore shocks have improved smoothness, improving suspension travel and increasing overall traction.

Lastly, the B44.3 comes with the latest JConcepts Finnisher X-Flow body and AE 6.5” high downforce wing.

The RC10B44.3 has been given all of the design advantages that only a winning pedigree like Team Associated can provide.

If you are ready to take your 1:10 4WD off-road program up to the next level, the B44.3 is ready to take you there!

Features in the B44.3 Factory Team:

• Hard anodized aluminum chassis and 7075-T6 floating motor mount allows for front or rear motor configurations

• New molded battery trays accommodate 2S saddle or shorty battery pack configurations and feature a quick-change strap with

• locking thumb knobs

• New front and rear carbon-fiber top decks and floating servo mount improves symmetrical chassis flex

• Front and rear gear differentials have machined steel ring, pinion, and planetary gears

• Center gear differential has independent fluid cap for quick and easy fluid or gear changes

• JConcepts Finnisher X-flow body

• Factory Team 0° 7075-T6 aluminum rear hubs with oversize outer bearing

• Factory Team V2 12mm “Big Bore” threaded aluminum shocks with 3mm shock shafts, molded caps with bleed screws, and

updated O-rings for improved smoothness

• Full CVAs and ball bearing drivetrain

• Factory Team 12mm blue aluminum rear clamping hexes and 12mm hex rear wheels

• Factory Team blue titanium turnbuckles, aluminum servo mounts, aluminum shock pivot balls and rear anti-roll bar included

• Silicone Shock Fluid (Refer to catalog for complete listings) • Silicone Diff Fluid (Refer to catalog for complete listings)

• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters • Hobby Knife

• FT Hex Wrenches (AE Part # 1655) • Needle Nose Pliers • Thread Lock (AE Part #1596)

• Soldering Iron • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)

3

:: Hardware - 1:1 Scale View

Notes:

E-clip 1/8 (6299)

Clips

Cap Head (shcs)

4-40x5/16 (6932)

(aluminum ,4145)

4-40x3/8 (6924)

(aluminum ,6860)

4-40x7/16 (7874)

(aluminum, 7873)

4-40x1/2 (6925)

4-40x7/8 (7738)

3x6mm (6515)

(motor mounting screws)

Ball Bearings

Steering Bearing (9746)

3/16x5/16 (6906)

3/16x3/8 (3977)

3/16x1/2 RS (7935)

(for optional

slipper assembly)

3/8x5/8” RS (3976)

4-40 Aluminum Locknut (4449)

4-40 Plastic Nut (6472)

5-40 Nylon Locknut (6222)

8-32 LP Steel Locknut (6953)

8-32 Steel Locknut (6952)

Nuts (lock/plain)

Top Hat Bushings

Small Top Hat Bushing (3874)

Large Top Hat Bushing (9647)

Ballstuds

Silver .20 Short (6276)

Silver .30 Long (6277)

Black .30 Short (3983)

2.5x10mm (31522)

3x6mm (31531)

2-56x1/8 (9645)

2-56x5/16 (4334)

4-40x1/4 (6288)

4-40x3/8 (6917)

4-40x7/16 (2221)

4-40x3/4 (7413)

Button Head (bhcs)

2.5x10mm (31350)

4-40x5/16 (7673)

4-40x3/8 (6292)

4-40x7/16 (9765)

4-40x5/8 (6915)

Flat Head (fhcs)

.030 Ballstud Washer (9630)

.030 Nylon Spacer (4187)

Servo Mount Washer (7337)

#4 Washer (6936)

Diff Shims (9957)

3/16 Axle Shim - Silver (7368)

HD Outdrive Shim (1733)

Shims and Washers

4

:: Table of Contents

:: Notes

1....................Cover

2....................Introduction

3....................1:1 Hardware “Fold Out”

4....................Table of Contents

5 - 6..............Front /Center/Rear

Differential Build (Bag A-AA)

7 - 8..............CVA Build (Bag B-BB)

8....................Front/Rear Gearbox Build

(Bag C)

9 - 10...........Steering and Center Battery

Brace Build / Install

(Bag D)

10 - 11.........Front End Build (Bag E)

11.................Rear End Build (Bag F)

12 - 13.........Center Bulhead Mounts Install

(Bag G-GG)

13.................Front Top Deck Build (Bag H)

14.................Rear Top Deck Build (Bag I)

15.................Turnbuckles Build (Bag J)

15 - 16........Front Suspension Build (Bag K)

16 - 18........Rear Suspension Build

(Bag L-LL)

18 - 19........Shock Build/Install (Bag M-MM)

20................Battery Cradle/Strap Build

(Bag N-NN)

21.................Servo Build (Bag O-OO)

22.................Servo Chart

22.................Electronics Install

23 - 24.......Body, Wheel, Tires Install

(Bag P)

24.................Notes

25 - 26........Tuning Tips

27 - 35.......Catalog

36.................Setup Sheet “Kit Setup”

37.................Setup Sheet “Blank”

38.................Back Cover

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

There is a 1:1 hardware foldout page in the

front of the manual. To check the size of a part,

line up your hardare with the correct drawing

until you find the exact size. Each part in the

foldout has a number assigned to it for ordering

replacement parts.

This symbol indicates a special

note or instruction in the manual.

This symbol indicates a Racers Tip.

!

5

:: Front and Rear Gear Differential Build - Bag A-AA - Step 1

:: Front and Rear Gear Differential Build - Bag A-AA - Step 2

:: Front and Rear Gear Differential Build - Bag A-AA - Step 3

1/15

9957

Shim

(0.17mm)

9937

O-ring

(3.6 x 0.7)

9937

O-ring

(4.7 x 1.42)

9937

B44.3 gear

diff outdrives

9957

Shim

(0.17mm)

9934

B44.3 ring

gear

9935

B44.3

diff case

(front/rear)

91463

Gear diff

sun gear

91463

Gear diff

sun gear

9937

Pin,

2x9mm

1733

Heavy

Duty Shim

9957

Shim

(0.17mm)

x2

x6

x2

Build x2

9935

B44.3

diff gasket

91463

Gear diff

gears, shims,

and pins

6903

3/8 x 5/8,

bearing

31350

2.5x10mm

fhcs

x2

x4

Tighten the

screws evenly in a

crossing order!

NOTE: Use one

drop of diff fluid

to hold gasket

in place.

Check for smooth diff action, adjust

shimming as needed.

• Moving shims #9957 from inside

to outside will loosen the diff.

• Moving shims #9957 from

outside to inside will tighten the diff.

• NOTE: not all shims may be

needed to get the desired feel.

!

#6588

black grease

#6588

black grease

5k diff

fluid #5453

9937

Pin,

2x9mm

NOTE: Use full

depth slot to

slide pin in!

!

5k diff

fluid #5453

Add diff fluid before

installing sun gear.

Fill diff half way full.

!

6

:: Center Gear Differential Build - Bag A-AA - Step 1

:: Center Gear Differential Build - Bag A-AA - Step 2

:: Center Gear Differential Build - Bag A-AA - Step 3

9938

B44.3 81T

spur, gear diff

9957

Shim

(0.17mm)

9937

O-ring

(3.6 x 0.7)

9937

O-ring

(4.7 x 1.42)

9937

B44.3 gear

diff outdrives

9957

Shim

(0.17mm)

9936

B44.3

center diff

case

9936

B44.3

center diff

case

91463

Gear diff

sun gear

9937

Pin,

2x9mm

9937

Pin,

2x9mm

9957

Shim

(0.17mm)

x2

Build x2

91463

Gear diff

gears, shims,

and pins

6919

4-40x5/16

bhcs

x4

Tighten the

screws evenly in a

crossing order!

!

#6588

black grease

#6588

black grease

9936

B44.3

diff gasket

31522

2.5x10mm

bhcs

x4

NOTE: Use one

drop of diff fluid

to hold gasket

in place.

!

Check for smooth diff action, adjust

shimming as needed.

• Moving shims #9957 from inside

to outside will loosen the diff.

• Moving shims #9957 from

outside to inside will tighten the diff.

• NOTE: not all shims may be

needed to get the desired feel.

2x9mm

91463

Gear diff

sun gear

Add diff fluid before

installing sun gear.

Fill to flat section.

Add diff fluid before

installing sun gear.

Fill diff half way full.

!

60k diff

fluid #5458

60k diff

fluid #5458

60k diff

fluid #5458

7

:: CVA Build - Bag B-BB - Step 1

:: CVA Build - Bag B-BB - Step 2

:: CVA Build - Bag B-BB - Step 3

Front and

Front Center

CVA Bone:

Front and Rear CVA Build:

Center CVA Build:

Rear Center

CVA Bone:

Rear

CVA Bone:

Align the gap in

the pin retainer

to be opposite of

the CVA pin.

NOTE: the front

and rear CVA

axles have threads

on the ends.

!

#1597

ca glue

#1597

ca glue

Racer’s Tip:

Try using only 1 drop of CA glue

to secure the pin retainer!

1 drop!

#6588

black grease

7996

CVA pin

retainer

9747

CVA bone

(front)

9748

CVA axle

(front)

9748

CVA axle

(front)

9942

B44.3 input

shaft

(gear diff)

9942

B44.3 input

shaft

(gear diff)

9755

CVA axle

(rear)

9755

CVA axle

(rear)

9747

CVA bone

(center, front)

9754

CVA bone

(rear)

9596

CVA bone

(center, rear)

7381

CVA pin

7381

CVA pin

9747

CVA bone

9596

CVA bone

9754

CVA bone

Build x4 (2 front, 2 rear)

Build x2 (1 front, 1 rear)

7996

CVA pin

retainer

NOTE: the front

and rear center

CVA axles have

flats on the ends.

!

#6588

black grease

CVA Bone:

x3

81.4mm

CVA Bone:

x1

92.2mm

CVA Bone:

x2

68.7mm

6906

3/16x3/8

bearing

9933

B44.3 input

pinion gear

3911

Drivetrain

shim

x2

6906

3/16x3/8

bearing

3911

Drivetrain

shim

x2

Align the gap in

the pin retainer

to be opposite of

the CVA pin.

!

CVA axle

(front)

9942

B44.3 input

8

:: CVA Build - Bag B-BB - Step 4 :: Front and Rear Gearbox Build - Bag C - Step 1

#6588

black grease

9733

Lower

transmission

case

1 drop!

6299

E-clip,

1/8

Center CVA Build:

Saddle Pack Configuration:

Shorty Pack Configuration:

-OR-

NOTE:

Optional ball diff

kits are available,

AE #9735.

NOTE:

Optional ball diff

kits are available,

AE #9735.

NOTE: The

orientation of

the gear diffs for

the shorty pack

configuration.

NOTE: The

orientation of

the gear diffs for

the saddle pack

configuration.

NOTE: Adjust diff

shimming side to side

until diff spins free

with minimal backlash.

NOTE: Adjust diff

shimming side to side

until diff spins free

with minimal backlash.

!

6924

4-40x3/8

shcs

#6588

black grease

x6

9733

Upper

transmission

case

1 drop!

6924

4-40x3/8

shcs

#6588

black grease

x6

9733

Upper

transmission

case

1 drop!

:: Front and Rear Gearbox Build - Bag C - Step 2

:: Front and Rear Gearbox Build - Bag C - Step 3

:: Front and Rear Gearbox Build - Bag C - Step 1

:: Steering and Center Battery Brace Build - Bag D - Step 1

1mm

9743

Spring

retainer

9743

Steering

v-spacer

9743

Servo

saver

upper

9744

5-40

locknut

9744

Servo saver

spring

9743

Servo saver

lower

6272

Dust cover

foam

6276

Ballstud, .20

silver, short

x2

9744

Steering

post

x2

9

:: Steering and Center Battery Brace Build - Bag D - Step 2

:: Steering and Center Battery Brace Build - Bag D - Step 3

6917

4-40x3/8

bhcs

3874

Black carrier

bushing

x2

9746

Steering

bearing

set

x2

9946

B44.3

aluminum

chassis

9743

Steering

retainer

column

6292

4-40x3/8

fhcs

x2

Use the small hole

bearings!

!

7673

4-40x5/16

fhcs

9905

Center

battery

cradle

x2

6272

Foam dust

cover

9630

.030

washer

6277

Ballstud, .30

silver, long

x2

9743

Steering

rack

10

:: Front End Build - Bag E - Step 1

:: Front End Build - Bag E - Step 2

6292

4-40x3/8

fhcs

x2

6292

4-40x3/8

fhcs

4449

4-40x3/16

aluminum

locknut

9713

Front

bulkhead

9765

4-40x7/16

fhcs

x2

9715

Front arm

x2

#1596

thread lock

9717

Front hinge

pin brace

9645

2-56x1/8

bhcs

9716

Front inner

hinge pin

x2

Front/Center CVA Gearbox Install:

:: Steering and Center Battery Brace Build - Bag D - Step 4

9746

Steering

bearing

set

x2

6292

4-40x3/8

fhcs

9743

Steering

retianer top

Use the large hole

bearings!

!

:: Front End Build - Bag E - Step 3

6917

4-40x3/8

bhcs

9718

Front

bumper

x2

#1596

thread lock

9903

Front shock

tower

7413

4-40x3/4

bhcs

9945

V2 aluminum

shock bushing

6917

4-40x3/8

bhcs

x2

11

:: Rear End Build - Bag F - Step 1

:: Rear End Build - Bag F - Step 2

6915

4-40x5/8

fhcs

9726

Rear arm

mount

9645

2-56x1/8

bhcs

6292

4-40x3/8

fhcs

9716

Rear inner

hinge pin

4449

4-40x3/16

aluminum

locknut

4449

4-40x3/16

aluminum

locknut

6936

#4 washer

9764

Rear

arm

9718

Rear

bumper

9726

Rear

chassis

plate

9765

4-40x7/16

fhcs

7673

4-40x5/16

fhcs

x2

x4

x2

x3

x2

Rear/Center CVA Gearbox Install:

Racers Tip:

Ensure arms can

move freely.

12

:: Center Bulkhead Mounts Install - Bag G-GG - Step 2

:: Center Bulkhead Mounts Install - Bag G-GG - Step 3

NOTE:

If using the optional slipper,

note the orientation for

installation (Slipper spring

towards rear of vehicle)!

Requires #9947 Center

CVA Kit.

!

Optional Slipper

(not included in kit)

6903

3/8x5/8

bearing

9940

B44.3 center

bearing insert

x2

Slipper

(For optional slipper

assembly, small hole)

Slipper Not Included!

Gear Diff

(Large hole)

:: Center Bulkhead Mounts Install - Bag G-GG - Step 1

9932

B44.3

motor mount

9932

B44.3

motor mount

9931

B44.3 center

bulkhead

9931

B44.3 center

bulkhead

6292

4-40x3/8

fhcs

6292

4-40x3/8

fhcs

x4

#1596

thread lock

#1596

thread lock

Key CVA bones in

the diff

outdrives!

Key CVA bones in

the diff

outdrives!

Note the gear diff

orientation when

installing

(BHCS facing front

of the vehicle)!

Note the gear diff

orientation when

installing

(BHCS facing rear

of the vehicle)!

! !

!

Saddle Pack Configuration:

Shorty Pack Configuration:

-OR-

:: Center Bulkhead Mounts Install - Bag G-GG - Step 4

:: Front Top Deck Build - Bag H - Step 1

9913

Antenna

mount

9714

Shock

tower

mount

9950

B44.3

Top deck,

front

9719

Body

mount

4334

2-56x5/16

bhcs

6917

4-40x3/8

bhcs

x2

6937

4-40 blue

aluminum

locknut

6936

Washers,

aluminum

#4

6277

Ballstud, .30

silver, long

x2

6288

4-40x1/4

bhcs

Motor not

included!

Pinion and

setscrew not

included!

31531

M3x6mm

bhcs

6924

4-40x3/8

shcs

9630

Ballstud

washer

9932

B44.3

motor mount

x2

Set gear mesh!

!

13

:: Front Top Deck Build - Bag H - Step 2

6917

4-40x3/8

bhcs

x2

6292

4-40x3/8

fhcs

x5

#1596

thread lock

14

:: Rear Top Deck Build - Bag I - Step 3

6917

4-40x3/8

bhcs

2221

4-40x7/16

bhcs

9913

Center

bulkhead

brace

x2

x4

#1596

thread lock

:: Rear Top Deck Build - Bag I - Step 2

7738

4-40x7/8

shcs

6925

4-40x1/2

shcs

9729

Wing mount

(right, left)

4449

4-40x3/16

aluminum

locknut

x3

x2

:: Rear Top Deck Build - Bag I - Step 1

7413

4-40x3/4

bhcs

6292

4-40x3/8

fhcs

9719

Body

mounts

x2

6917

4-40x3/8

bhcs

6924

4-40x3/8

shcs

9904

Shock tower,

rear

9714

Shock tower

mount

x2

#1596

thread lock

6277

Ballstud, .30

silver, long

6937

4-40 blue

aluminum

locknut

9951

B44.3 top

deck, rear

6936

Washers,

aluminum #4

x2

#1596

thread lock

9945

V2 aluminum

shock bushing

x2

:: Turnbuckles Build - Bag J - Step 1

Front Steering Link

Front Camber Link

Rear Camber Link

Steering

Build x2

Front Camber

Build x2

Rear Camber

Build x2

1406

FT titanium

turnbuckles

2.00

1406

FT titanium

turnbuckles

2.00

1404

FT titanium

turnbuckles

1.77

7499

Low friction

ball cup

7499

Low friction

ball cup

7499

Low friction

ball cup

x2

Build x2

32.5mm

Build x2

24.5mm

Build x2

29mm

:: Front Suspension Build - Bag K - Step 1

4449

4-40x3/16

aluminum

locknut

9722

Steering

block

(right, left)

6277

Ballstud, .30

silver, long

6272

Foam dust

cover

x2

3977

3/16x3/8

bearing

x4

9751

Crush tube

x2

Left Side

Right Side

15

:: Front Suspension Build - Bag K - Step 2

7369

1/16 axle

roll pin

6272

Dust cover

foam

9750

Axle drive

hex

4449

4-40x3/16

aluminum

locknut

9720

Caster block

(right, left)

3983

Ballstud, .30

black, short

x2

Right Side

Left Side

Right Side

Left Side

Racers Tip:

Use black grease

(#6588) on the

threads of the

turnbuckles for

easier ball cup

installation!

16

:: Rear Suspension Build - Bag L-LL - Step 1

3977

3/16x3/8

bearing

9872

FT aluminum

hub tower

(A)

9864

FT aluminum

hub ( 0˚)

6272

Dust cover

foam

7933

Crush tube

3983

Ballstud, .30

black, long

x2x2

x2

6932

4-40x5/16

shcs

7935

.187x.196

bearing

x4

x2

Left Side

Molded camber link

tower “A” has

standard holes, and

optional “B” tower

has “in-between” hole

options!

!

A

Build x2 (right and left side)

#1596

thread lock

:: Front Suspension Build - Bag K - Step 4

9645

2-56x1/8

bhcs

Build x2 (right and left side)

9716

Hinge pin

set

Front

camber

link

Front

steering

link

Install x2 (right and left side)

Orient the notch

to the left

throughout the

car. It indicates

which end has the

left hand threads!

!

:: Front Suspension Build - Bag K - Step 3

2221

4-40x7/16

bhcs

9647

Steering

block bushing

x4

Left Side

Right Side

:: Rear Suspension Build - Bag L-LL - Step 3

Install x2 (right and left side)

31286

Aluminum

ballstud

washer, 1mm

(blue)

9630

.030 ballstud

washer

9645

2-56x1/8

bhcs

9716

Hinge pin

set

Rear

camber

link

Orient the notch

to the left

throughout the

car. It indicates

which end has the

left hand threads!

!

17

:: Rear Suspension Build - Bag L-LL - Step 4

8830

Anti roll

bar pivots

9170

4-40x1/2

set screw

x2

Build x2

8828

Ball cup,

short

23mm

Install x2 (right and left side)

:: Rear Suspension Build - Bag L-LL - Step 2

7368

3/16

axle shims

7369

1/16

roll pins

9660

2-56 x 7/32

shcs

9890

12mm aluminum

clamping wheel

hex, buggy rear

x4

Build x2 (right and left side)

:: Shocks Build - Bag M-MM - Step 2

18

1777

FT shock

pivot ball

1777

Shock

eyelet

91480

12x23mm V2

shock bodies

(front)

91482

12x31mm V2

shock bodies

(rear)

91491

Shock hat

bushing

91491

Shock

spacer

5407

O-ring

31327

VCS3 shock

bottom cap

31327

VCS3 shock

bottom cap

o-ring

91491

12mm shock

cap o-ring

x2

#1105

green slime

Racers Tip:

Lightly rub shock oil on the

o-ring before installation!

NOTE: Use #4187

when building rear

shocks only!

!

:: Shocks Build - Bag M-MM - Step 1

91308

12mm shock

piston

(1.5 front)

(1.7 rear)

91488

3x21

shock shaft

(front)

91489

3x27.5

shock shaft

(rear)

6299

1/8 E-clip

6299

1/8 E-clip

4187

Nylon spacer,

(.030)

4187

Nylon spacer,

.030

Racers Tip:

Use a marker over the

numbers on the pistons to

make them easily visible!

Front:

1 spacers

Rear:

1 spacers

:: Rear Suspension Build - Bag L-LL - Step 5

6951

4-40x1/8

setscrew

x2

Optional silver

anti-roll bar also

included!

!

Adjust so that the

anti roll bar is level

and the end link is

90° to the anti roll

bar at ride height.

!

4334

2-56x5/16

bhcs

89278

Washer,

2.5mm

9780

0.47 black

anti-roll bar

x2

Make sure endlinks

pivot freely!

Racers Tip:

Coating the o-rings

with green slime

(#1105) helps seal

& reduce o-ring

swell! Green slime

not included in kit!

#1105

green slime

:: Shocks Build - Bag M-MM - Step 4

91304

12mm

threaded

collar

91304

12mm

threaded

collar

o-ring

x4

91310

12mm shock

spring cup

(5mm offset)

91332

12mm front

spring, Red

(3.90lb)

91336

12mm rear

spring, Green

(2.00lb)

Front:

4.5mm

Rear:

1.6mm

Build x2 front and x2 rear shocks

Racers Tip:

Use your finger to rub

shock oil on the o-ring for

smoother adjustment!

19

:: Shocks Build - Bag M-MM - Step 5

6472

Shock

mount nut

6925

4-40x1/2

shcs

6925

4-40x1/2

shcs

6472

Shock

mount nut

91447

Shock

bushing

ball

91447

Shock

bushing

ball

x2

9mm

Offset

5mm

Offset

0mm

Offset

:: Shocks Build - Bag M-MM - Step 3

x4

91449

12mm

shock cap

Step 9-10Step 8Step 6-7Step 4-5

Front Shock: 35 wt

Rear Shock: 35 wt

Step 2-3

Shock Bleeding Steps:

1. Before assembly, get each bleed

screw and thread it 1-2 turns into the

shock cap. This will make installation

easier when you are bleeding your

shocks.

2. Pull shock shaft down completely.

3. Fill shock body 3/4 full with silicone

shock fluid.

4. Slowly move the shock shaft up and

down to remove air from under the

piston.

5. Wait for bubbles to come to surface.

6. Fill shock body to top with silicone

shock fluid.

7. Place a drop of oil in the cap and on

cap threads.

8. Install cap (without bleed screw) and

tighten completely.

9. Slowly compress shaft all the way to

bleed excess silicone shock fluid out

the hole in the cap (use rag around-

shock to catch excess fluid).

10. Install M2x4mm button head screw

until snug while shaft is fully com-

pressed.

Shock oil

#5429

Shock oil

#5429

31510

M2x4mm

bhcs

x4

20

:: Battery Cradle / Strap Build - Bag N-NN - Step 2

:: Battery Cradle / Strap Build - Bag N-NN - Step 3

Unlocked!

!

Locked!

!

9952

B44.3 shorty

battery

cradle

9952

B44.3 shorty

battery side

rail

9952

B44.3 shorty

battery strap

6922

4-40x1/2

fhcs

6292

4-40x3/8

fhcs

x2

LiPo battery

not included!

9906

Battery

strap

locks

9906

Ball

joint

9906

4-40x5/8

set screw

:: Battery Cradle / Strap Build - Bag N-NN - Step 1

6922

4-40x1/2

fhcs

9905

Battery

cradle

9905

Battery

spacer

x4

x2

LiPo batteries

not included!

x2

9906

Battery

straps

9906

Battery

strap

locks

9906

Ball

joint

9906

4-40x5/8

set screw

Saddle Pack Configuration:

Shorty Pack Configuration:

-OR-

Page is loading ...

AE B44.3 Factory Team User manual

AE B44.3 Factory Team User manual

Related papers

Other documents