Tesco 26W Soundbar with Bluetooth User guide

Tesco
Brand
Tesco
Model
26W Soundbar with Bluetooth
Category
Bluetooth music receivers
Type
User guide
’s
TSB17
26W Bluetooth soundbar
User Guide
1
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Do not install or operate near any heat sources such
as radiators, stoves, or other apparatus that produce
heat.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
IMPORTANT
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communication. However, this
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit dierent from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
ELECTRICAL INFORMATION
Use this appliance only with the supplied AC Adapter.
Using non-approved power supplies will void the
warranty.
Mains Supply: The mains operating voltage of this unit
is marked on a rating plate on the AC adapter.
The means of disconnecting this appliance from
the mains supply is the mains plug. This should be
unobstructed and readily operable at all times.
Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
Batteries (a battery pack or installed batteries) shall
not be subject to excessive heat such as sunshine, re
or the like.
Warning: To reduce the risk of re or electrical shock,
do not expose this product to rain or moisture. The
product must not be exposed to dripping and splashing
and no object lled with liquids such as a vase of
owers should be placed on the product.
No naked ame sources such as candles should be
placed on the product.
Caution: Changes or modications not expressly
approved by the manufacturer could void the user’s
authority to operate this device.
Caution: Usage of controls or adjustments or
performance of procedures other than those specied
herein may result in hazardous exposure.
This symbol indicates that there are important
operating and maintenance instructions in
the literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
IMPORTANT SAFETY INFORMATION
2
INDEX
PRELIMINARIES INTRODUCTION
UNPACKING
Carefully unpack the unit. If it is damaged, please
return it to your nearest Tesco store for replacement.
Remember to take your purchase receipt with you.
Retain the User Handbook. If you pass the unit on to a
third party make sure you pass on the handbook.
We suggest you retain the packaging. If you dispose of
it, do so having regard to any recycling regulations in
your area.
CONTENTS
The carton should contain:
The TSB17 26W Bluetooth Soundbar•
AC adapter•
Remote control with battery•
3.5mm jack/jack cable•
Operating Manual•
If any items are missing or damaged, contact your
nearest TESCO store for a replacement. Have your
receipt ready when you call. Retain the packaging. If
you dispose of it, do so having regard to any recycling
regulations in your area.
The TSB17 Mini Soundbar is a versatile speaker unit
with Bluetooth connectivity and both digital and
analogue audio inputs for audio-visual sources.
Recommended sound sources include -
Play music from your mobile phone, tablet or •
notebook computer via Bluetooth.
Connect digital sources such as TV, satellite receiver •
or DVD player via the OPTICAL digital input.
Connect an analogue audio source such as TV, •
DVD player, satellite receiver, computer or personal
audio player to the AUX Input.
The unit is operated by the supplied remote control or
via the touchpads on the control panel.
LOCATION
LOCATION
Place the unit on dry stable surface away from heat
and damp and where it is unlikely to fall or be knocked
over. Check that connecting cables are tucked away
and will not cause a risk of tripping etc.
If you are using your Soundbar for TV sound, place it
centrally under, or above the TV screen.
CAUTION: This Soundbar is not intended to be a TV
stand. Do Not stand a TV on it.
Contents
IMPORTANT SAFETY INFORMATION............................ 1
INDEX ........................................................................ 2
PRELIMINARIES ......................................................... 2
INTRODUCTION .......................................................... 2
LOCATION .................................................................. 2
CONTROLS AND DISPLAY ............................................ 3
CONNECTIONS ........................................................... 4
CONNECTING A DIGITAL AUDIO SOURCE .................... 5
CONNECTING TO A TV HEADPHONE JACK .................... 5
CONNECTING TO TV LINE OUT JACKS ........................... 6
CONNECTING A COMPUTER OR PORTABLE AUDIO PLAYER
....
6
REMOTE CONTROL ..................................................... 7
REMOTE CONTROL BATTERIES .................................... 7
CONNECTING POWER ................................................. 8
FRONT PANEL CONTROLS ........................................... 8
OPERATION ................................................................ 8
OPERATION ................................................................ 9
CARE AND MAINTENANCE ....................................... 10
TROUBLESHOOTING ................................................ 10
SPECIFICATIONS ...................................................... 10
WARRANTY ............................................................. 10
3
b
d f h 1) 1@
c
a
e
i
1!
1#
g
CONTROLS AND DISPLAY
Optical Source indicator1.
Source select2.
AUX Source indicator3.
EQ touchpad4.
Bluetooth source indicator5.
CONTROL PANEL VIEW
PAIR touchpad6.
Standby button7.
Mute touchpad8.
Game EQ indicator9.
Volume down touchpad10.
Music EQ indicator11.
Volume up touchpad12.
Movie EQ indicator13.
4
CONNECTIONS
Optical digital input port 1.
Aux input jack2.
DC In jack3.
TERMINAL PANEL VIEW
OPTICAL
AUX IN
DC IN 15V
2A
b
a
c
5
OPTICAL
AUX IN
DC IN 15V
2A
You will need a jack to jack connecting cable (supplied)
terminated with a 3.5mm plug at each end.
Connect the cable to the AUX IN input jack.•
Connect the jack plug at the other end of the cable •
to the headphone jack of your TV.
Set the TV to play and turn up the TV headphone •
volume to about 50%.
Volume level can now be set from the Soundbar.•
Stereo 3.5mm jack cable
CONNECTING TO A TV HEADPHONE JACK
OPTICAL
AUX IN
DC IN 15V
2A
CONNECTING A DIGITAL AUDIO SOURCE
Your Soundbar is compatible with optical digital
sources. Always use this connection where possible for
the best quality. Compatible sources may include
TVs,
satellite receivers and DVD players. Some computers also
have digital outputs.
Before connecting your source, check that it has the
correct Optical outlet.
NOTE: If the source features Home Cinema surround-
sound, you should set the digital output to two channel
stereo. This is usually an option in the setup menu.
To connect to the OPTICAL input you will need an
optical bre interconnect (not supplied).
Connect the optical interconnect to the OPTICAL •
input jack of your Soundbar.
Connect the other end of the interconnect to the •
Optical outlet of your source.
OPTICAL CONNECTION
Optical
interconnect
Connect to the
optical outlet
6
OPTICAL
AUX IN
DC IN 15V
2A
To connect a computer or portable audio player:
You will need a jack to jack connecting cable (supplied)
terminated with a 3.5mm plug at each end.
Connect the cable to the AUX IN input jack.•
Connect the jack plug at the other end of the cable •
to the headphone jack of your computer or portable
audio player.
Set the player to play and turn up the player •
volume.
Volume level can now be set from the Soundbar.•
Stereo 3.5mm jack cable
CONNECTING A COMPUTER OR PORTABLE AUDIO PLAYER
CONNECTING TO TV LINE OUT JACKS
Analogue line out sources may include -
Audio from a TV. •
Audio from a satellite receiver or DVD player.•
You will need to buy an audio cable terminated with
connections to match your source at one end and a
3.5mm stereo jack to match your soundbar at the other
end.
To connect a TV line out etc to the analogue input:
Connect the 3.5mm jack to the AUX IN socket.•
Connect the other end of the cable to the output •
jack(s) of your source. If they are dual colour coded
plugs, the white plug connects to the left channel,
the red plug connects to the right channel.
From the analogue
audio outputs of the TV etc
CONNECTING AN ANALOGUE SOURCE
3.5mm jack plug
7
REMOTE CONTROL
Standby1.
AUX source select2.
Equalisation3.
Mute4.
Bluetooth source select5.
Optical source select6.
Volume up7.
Previous track8.
Next track9.
Volume down10.
Play/Pause11.
REMOTE CONTROL BATTERIES
EQ
c
a
d
e
f
i
h
g
1)
b
1!
BEFORE FIRST USE
To prepare the remote control for
rst use, pull out the safety strip to
activate the battery.
REPLACING THE BATTERY
When replacing the battery in the remote
control, refer to the diagram below.
Press the catch across.1.
While holding the catch, open the 2.
battery door.
Dispose of used batteries with regard to the recycling regulations in your area. Do NOT
short circuit batteries or throw them into water, the general rubbish or in a re.
Weak batteries can leak and damage the remote control. Replace them in good time!
a
b
Fit the battery observing polarity 3.
as shown. When replacing the
battery, use only the same
CR2025 type specied.
8
OPERATION
POWER CONTROL
To switch the unit on
Press the •
button.
The unit will switch on and the last selected Source
indicator will light.
To switch the unit o
Press the •
button.
The unit will switch o.
If you plan to leave the Soundbar unattended for long
periods (for example, holidays), switch o the mains
power by disconnecting the AC adapter from the mains.
Auto Standby
The Soundbar will set to Standby automatically if
standing idle for 120 minutes with no signal. This is an
energy saving feature.
CONNECTING POWER
Before connecting the Soundbar to mains power, check
that the mains supply voltage in your area is within the
range specied on the rating label on the AC adapter.
Plug the DC cable from the AC adapter into the DC •
IN jack on the back panel.
Plug the AC adapter into the wall socket and switch •
the mains power on.
VOLUME CONTROL
NOTE: When playing a source connected to the AUX IN
jack it will be necessary to set the volume on the source
to around 50%. The volume level may then be set from
the Soundbar.
Press •
or to increase or reduce the volume
level from the Soundbar.
To mute the volume:
Press •
on the remote control (or touch on the
front panel) to mute the sound.
The sound will mute and the selected source indicator
will ash slowly.
Press again to restore the volume level to its •
original setting.
SELECTING A SOURCE
Selecting a source from the remote control
Press •
, AUX or OPT to select the Bluetooth, AUX
IN or Optical source.
The Source indicator will light to conrm the source
selected.
Set the source to play. If the source has a volume •
control (for example, a personal audio player), this
may need to be turned up.
Selecting a source from the control panel
Touch • SOURCE repeatedly to switch between
sources.
The Source indicator will light to conrm the source
selected.
FRONT PANEL CONTROLS
The instructions in this handbook always refer to
remote control button functions.
In addition, some controls are duplicated on the top
panel for convenient operation when close to the unit.
Where the top panel controls are named dierently
this will be indicated in the text of the handbook.
Touch controls
The top panel controls for volume, mute, source, mode
and pairing are touch pads. Touch the control name to
select a function.
9
OPERATION
PLAYING A BLUETOOTH SOURCE
Before playing from a Bluetooth source, it will be
necessary to pair the source to your Soundbar.
Pairing with a Bluetooth device
Switch on the Soundbar.•
Select the • Bluetooth source.
If no device has been paired to the Soundbar, the
Bluetooth source indicator will ash.
Activate • Bluetooth communication on the source.
If the source is a phone, Bluetooth communication will
normally be activated in the connectivity section of the
settings menu.
If the source is a computer, Bluetooth settings should be
found in the Control Panel.
In the • Bluetooth menu of the source, there should
be an option to search for Bluetooth devices. Select
this option.
The source will now scan for other Bluetooth devices
and should nd the unit, identied as ‘TSB17’.
Choose to pair with this.•
If the device features Bluetooth technology earlier than
V2.1, you will be asked for a password.
If so, enter 0000.•
Your Bluetooth source will now be connected to the
Soundbar.
EQUALISATION
Your Speaker Bar includes four sound equalisation
modes, optimised for dierent types of programme
content.
Changing the equalisation setting
Press • EQ repeatedly to step through the available
equalisation mode options.
These are -
Game mode (•
indicator).
Music (•
indicator).
Movie (•
indicator).
Normal, no equalisation (all indicators o).•
The Bluetooth source indicator will stop ashing when
paired.
After pairing for the rst time, the Soundbar will appear
in the connection menu of your Bluetooth device.
Re-connecting
Your device and the Soundbar should re-connect when
next used if no other device is connected.
Disconnecting a Bluetooth source
To disconnect the Bluetooth source that is currently
paired to your soundbar -
Touch and hold • PAIR.
The Bluetooth source will be disconnected.
The Bluetooth source indicator will ash.
You can now pair a dierent device to the Soundbar.
Playback control of a Bluetooth source
Some Bluetooth sources support remote control of
playback control functions. If this is the case, you will
be able to control the source from the Soundbar remote
control.
NOTE: Some sources may not support some or all of the
functions listed.
Press the • /, button to switch between play and
pause modes.
Press the • } or { button to select the next or
previous track.
10
AFTER USING THE SOUNDBAR
Set it to Standby.•
CARE AND CLEANING
All care and cleaning operations should be carried out
with the unit unplugged from the mains power.
The surface of the unit can be cleaned with a dry
cloth. Never use abrasives, abrasive cloths or chemical
solvents .
Loudspeaker grilles can be cleaned carefully with a soft
brush.
Supply Voltage ................... 15 V
, 2A
AC adapter input ................ 100 - 240 V ~, 50/60 Hz
AC adapter output ............... 15 V
, 2A
Power consumption ............ 30 W
Net Weight: ......................... 1.2 kg
Class II construction double insulated.
This product must not be connected to earth.
UK: Waste electrical products/batteries
should not be disposed of with household
waste. Separate disposal facilities exist, for
your nearest facilities see www.recycle-
more.co.uk or in-store for details.
ROI: Produced after 13th August 2005.
Waste electrical products/batteries should
not be disposed of with household waste.
Please recycle where facilities exist. Check
with your Local Authority or retailer for
recycling advice.
CARE AND MAINTENANCE
WARRANTY
SPECIFICATIONS
Your Tesco appliance is covered by a warranty for 12
months from the date of purchase. If a fault develops
during this period, please contact the TESCO electrical
help line. Please have your original purchase receipt
with you when you call. This warranty in no way aects
your consumer rights.
TROUBLESHOOTING
No sound
Check that the Soundbar is not set to Standby.•
Check that the correct input is selected.•
No sound/low volume (computer or personal audio
player connected to the AUX IN input)
If the source has a volume control, check that this •
is turned up.
No sound (digital audio source)
Check that the sample rate of the source is in the •
correct range for the Soundbar.
No remote control operation
The batteries may be at. Try replacing the •
batteries.
The Soundbar sets to Standby when idle
The Soundbar will set to Standby automatically if
standing idle for 120 minutes with no signal. This is
normal and an energy saving feature. Press the
button to switch on and continue using the Soundbar.
NOTE: the auto-standby function may be enabled if
the volume of audio sources is set too low. To prevent
the soundbar entering the standby mode during use,
ensure the input device volume is more than 50%.
Volume can be adjusted on the soundbar or the remote
control.
Tesco Stores Ltd, Welwyn Garden City AL7 1GA, U.K.
TSB17 EN V1.8
Tesco Helplines:
Landlines 0800 323 4060 (Freephone from a BT landline).
Mobiles 0330 123 4060 (Calls cost no more than calls to geographic numbers eg. 01 or 02 and are included in inclusive minutes and discount
schemes).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Tesco 26W Soundbar with Bluetooth User guide

Tesco
Brand
Tesco
Model
26W Soundbar with Bluetooth
Category
Bluetooth music receivers
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents