Genie WNVRN216P5 User guide

Brand: Genie

Model: WNVRN216P5

Type: User guide

Quick Start Guide

Please read these instructions carefully before operating the unit

and keep for further reference.

PoE 16 Channel H.265 8MP NVR

with 2 HDD Bays

WNVRN216P5

Intro Section

Please read this instruction carefully before operating the product and keep it for further

reference. All examples and pictures used here are for reference only.

The contents of this manual are subject to change without notice.

This device should be operated only from the type of power source indicated on the

marking label. The voltage of the power must be veriﬁed before use.

CAUTION:

• Please check the device and the accessories after getting the device. If there are any

damages, shortages or defects, please contact your dealer immediately.

Contents

iii

1.0 Introduction .......................................................................................................... 4

1.1 Product Features ........................................................................................... 4

1.2 Product Dimensions .....................................................................................4

1.3 Speciﬁcation.................................................................................................5

2.0 HDD Installation ...................................................................................................6

3.0 Rear Panel Instruction .......................................................................................... 7

4.0 Start Up and Shut Down ......................................................................................8

5.0 Login ....................................................................................................................9

6.0 Conﬁgurations and Connections ........................................................................10

6.1 Network Conﬁguration & Adding IP Camera ............................................... 10

7.0 UPnP .....................................................................................................................12

8.0 NAT ....................................................................................................................... 13

9.0 Manual Recording and Playback .........................................................................14

9.1 Manual Recording .........................................................................................14

9.2 Playback .......................................................................................................14

1.0 Introduction

The Genie WNVRN216P5 is a 16 channel PoE H.265 8MP NVR with 2 HDD bays. The NVR

supports 16 channel 8MP, 6MP, 5MP, 4MP, 3MP, 1080p, 1280 × 1024, 960p, 720p, 960H, D1

and CIF IP video input as well as 16 channel simultaneous playback.

1.1 Product Features

• Supports 16CH 8MP / 6MP / 5MP / 4MP / 3MP / 1080p / 1280×1024 / 960p / 720p /

960H / DI / CIF IP video input H.265S/H.265+/H.265/H.264 coding

• Intuitive and user-friendly Graphic User Interface ( GUI ), Windows style operation by

mouse

• Playback : 16CH simultaneous playback

• Search : time slice, time, event, tag and smart search

• Supports multiple VCA (Video Content Analytics) events, such as object abandoned/

missing, region intrusion, tripwire, video exception, etc. Supports POS information

overlay on live view and playback

• Express and ﬂexible backup via USB, network and so on

• Pentaplex : preview, record, playback, backup and remote access

• DHCP, DDNS, PPPoE network protocol

• Remote control via Web Client or CMS : preview, playback, backup, PTZ and

conﬁguration

• 16 PoE network ports; PoE power supply supported

• Powerful mobile surveillance by smart phones with iOS and Android OS Dual stream

technology for local storage with high deﬁnition, remote network transmission and

remote surveillance with mobile device

• Multi-user online simultaneously

• Authorisation management, log view and device status view

• 4K ultra high deﬁnition output, true high resolution display

• Supports NAT function and QR Code scanning by mobile phones

• NDAA compliant

1.2 Product Dimensions

380mm

268mm

45mm

Quick Start Guide PoE 16 Channel H.265 8MP NVR with 2 HDD Bays

1.3 Speciﬁcation

Model WNVR416P5AI

System OS Embedded Linux

Mobile OS iOS, Android

Video

Input 16 CH IPC input

Network Input Resolution 8MP / 6MP / 5MP / 4MP / 3MP / 1080p / 1280×1024 / 960p / 720p / 960H / D1 / CIF

Output HDMI x 1: 3840×2160 / 1920×1080 / 1280×1024 / 1024×768

VGA: 1920×1080 / 1280×1024 / 1024×768

Compression H.265S / H.265+ /H.265 /H.264

Audio

Input 16 CH IPC audio input

Output RCA × 1

Two-Way Audio RCA × 1

Compression G.711(U/A)

Playback

Simultaneous Playback Max. 16 CH

Search Time slice / Time / Event / Tag search / Smart search

Smart Search Highlighted colour to display the camera record in a certain period of time, different

colours refers to different record events

Function Play, Pause, FF, FB, Digital zoom, etc.

Decoding Capability 1CH 8MP / 4CH 1080p (Live View/Playback)

Alarm

Mode Manual, Sensor, Motion, Exception, Smart events

Input Supports IPC alarm input

Output Supports IPC alarm output

Triggering Record, Snap, Preset, E-mail, etc.

Network

Interface RJ45 1000Mbps x 1

Protocol TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP, HTTP, HTTPs, 802.1x, RTSP, SNMP,

ONVIF, etc.

PoE Port RJ45 × 8 (IEEE802.3af, output

power: ≤80W)

Incoming/Outgoing

Bandwidth 96Mbps/96Mbps

Client Connection Max.10 users access

Record Resolution 8MP/6MP/5MP/4MP/3MP/1080p/1280×1024/960p/720P/960H/D1/CIF

Frame Rate N:30fps, P:25fps

Backup &

Storage

Local Backup USB stick, USB mobile HDD

Network Backup Yes

Storage SATA3.0 × 2, max 10T per HDD

Remote

Monitoring

Immix Compatible with Immix via RTSP only (2-way audio not supported)

Sentinel Yes, Firmware 1.1.0 or later

Port

USB USB 2.0 × 2

Remote Controller Optional

PoE Ports RJ 45 100 Mbps × 16

Others

PoE Standards: IEEE802.3AF/AT, Output Power: ≤ 150W

Video Structure Analysis Human/Vehicle Classiﬁcation : Yes

Plate Recognition Yes

Power Supply DC 48V/3.75A

Consumption ≤ 10W (without HDD)

Dimensions 380 × 268 × 45 mm

Working Environment -10°C~50°C, 10%~90% humidity

Certiﬁcate CE, FCC

Environmental Protection Complies with Directive EU RoHS, REACH and WEEE

This series of the product supports 2 SATA hard drives. Please make sure that the device is

powered off before the installation. The pictures of the installation are for reference only.

1. Loosen the screws to open the cover.

2.0 HDD Installation

2. Place the HDD onto the bottom

of the machine.

3. Put the HDDs onto the bottom of the

device.

4. Connect the power and data

cables.

5. Turn over the machine and secure

the HDD with the screws.

6. Install back the cover and secure

it with the screws.

Note: Please check the inside structure of the device and make sure that the cables are

connected well before installing the cover back. Please format the HDD before using.

The interfaces of the rear panel are for reference only.

3.0 Rear Panel Instruction

Internet

DC48VUSB

LAN

PoE Ports IN

OUT

AUDIO

VGA

Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

Shutdown

Click “Start” and then select “Shutdown” icon. This will bring up a shutdown window. The

device will shut down by clicking “OK” button. Then disconnect the power.

4.0 Start Up and Shut Down

The default username is admin and the default password is 123456. You must conﬁgure the

wizard if you start the NVR for the ﬁrst time and you may change the password when you

conﬁgure the wizard for the ﬁrst time. You can skip the settings wizard next time.

Click “Start” and select “Login”. This will take you to see a login box. Enter the default

username and password you set. Then you will see the live image.

5.0 Login

6.0 Conﬁgurations and Connections

6.1 Network Conﬁguration & Adding IP Camera

After you ﬁnish adding IP cameras, you can see the live images through the monitor of the

NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.

LAN

1. Set the network of the NVR. Go to Start → Settings → Network → TCP/IP. Enter IP

address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the

NVR and the router.

2. Go to Start → Settings → Network → Port. Enter HTTP port (the default value is 80),

server port (the default port is 6036).

3. The internal ethernet port is the port which connects all the PoE ports with the NVR

system. The PoE ports are available if the internal ethernet port is online. If it is ofﬂine,

all the PoE ports will be unavailable. The IP address and subnet mask of the internal

ethernet port can be changed to make the port in the same network segment with the

IP cameras which directly connect to the PoE ports of the NVR.

4. Go to Start → Settings → Camera → Add Camera. The NVR will automatically refresh the

cameras searched. The IPC which supports the Onvif protocol may be added manually.

If the IPC searched is not in the same local network as the NVR, you should select the

device and click to modify the IP address.

Quick Start Guide PoE 16 Channel H.265 8MP NVR with 2 HDD Bays

5. Checkmark the device you want to add and then click “Add” button. The NVR will

automatically refresh the cameras and return to “Edit Camera” interface. “Online” status

means connecting the device successfully and you will see the live image. You may

select the added device and click button to modify channel, IP address, etc.

WAN

1. Set the network of the NVR. Go to Start → Settings → Network → PPPoE. Enable PPPoE

and then input the user name and password received from your ISP.

2. Go to Start → Settings → Camera. Click “Add Camera” or behind the column of the

search camera and select “Manually Add” to add the IP cameras. Enter IP address,

server port, username and password of the IP camera. The IP camera must be

connected over WAN. And here the IP address of the IP camera must be a WAN IP

address.

You can use the UPnP function to enable the fast connection of the device to WAN via a

router without port mapping.

1. Go to Start → Settings → Network → UPnP, and enable UPnP and then click “Apply”

button to save.

2. Enable the UPnP function in the router.

3. Click “Refresh” button to refresh the UPnP status. If the UPnP status were still “Invalid

UPnP” after refreshing it for several times, the port would be wrong. Please change the

mapping type to “Manual” and then click to modify the port until the UPnP status

turns to “valid UPnP”.

7.0 UPnP

8.0 NAT

NAT Settings

1. The NVR shall be powered on and connected to the network.

2. Go to Start → Settings → Network → TCP/IP. You can obtain the IP address, subnet mask

and gateway automatically. You can also manually enter them according to the actual

network situation. Please make sure the network segment is the same as that of the

network which is used.

3. Set the preferred or alternative DNS Server. Click “Apply” to save the parameters.

4. Go to Start → Settings → Network → NAT tab. Enable NAT and select the NAT Server

Address (The default NAT Server Address is nat.autonat.com). Click “Apply” to save the

parameters.

NAT Access

After ﬁnishing the NAT settings, you can enter www.autonat.com in the address bar of

your browser and then press enter to go to the following interface. If you are the ﬁrst time

to access the NAT, you shall download and install the plug-in according to the tips. After

installing the plug-in successfully, it will pop up the login box.

Device Serial Number:

Click on the menu bar at the bottom of the live interface to check the serial number or

go to Start → Settings → Network → Network Status to check the serial number of the NVR).

Username:

The username of the NVR. The default username is admin.

Password:

The password of the NVR. The password is set by yourself when you conﬁgure the wizard

for the ﬁrst time.

9.1 Manual Recording

Before recording, please install and format a HDD. In the live interface you can see the

menu toolbar. Click button to start recording. Click it again to stop recording. You can

also click to check the status of the recording.

9.2 Playback

Instant Playback

Click “Instant Playback” in the right-click menu of the camera’s preview window to

select or drag the playback progress bar to change the playback time to play back

the record.

General Playback

Click on the tool bar at the bottom of the live preview interface or click

Start → Playback to go to the playback interface as shown below. You can also

add the playback cameras manually. Click in the playback window to pop up the

“Add Camera” window. Check the cameras in the window and then click “Add” to

add playback camera. The record ﬁles of the added playback camera

will be played in the playback interface.

9.0 Manual Recording and Playback

Sales +44(0)1707 330541

Enquiries [email protected]o.uk

Website www.genieproducts.co.uk

Genie WNVRN216P5 User guide

Genie WNVRN216P5 User guide

Genie WNVRN216P5 User guide

Related papers

Other documents