Legrand OFR Series Overfloor Raceway Device Boxes Operating instructions

OFR Series

Overfloor Raceway Device Box

I N S T A L L A T I O N I N S T R U C T I O N S

Installation Instruction No.: 1 009 725 – February 2011

Legrand/Wiremold electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Legrand/Wiremold electrical

products may bear the mark of a Nationally Recognized Testing

Laboratory (NRTL) and should be installed in conformance with current

local and/or the National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

PRODUCTS COVERED: OFR48-2, OFR48-4, OFR48-4GX, OFR47-B, OFR47-D, OFR47-R, OFR47-2A,

OFR47-U, OFR47-V, OFR47-U2A

5. Mount the devices and device plates

to the device box.

• For device plates used with NEMA

standard devices (OFR47-D,

OFR47-R), mount as shown in 5A.

• For device plates, which mount

communications and AV devices

(OFR47-2A, OFR47-U, OFR47-V,

OFR47-U2A), remove break away

tabs as shown in 5B.

5A

5B

1. Insert device box connecting tabs into outer channels of

raceway base mounted to floor. Tighten (2) #8-32 screws

to secure.

2. Using #8 fasteners, install base of raceway directly on

top of existing floor covering. The screw type should be

appropriate for the type of floor, which the raceway is

being installed on.

3. Place wires in raceway base and attach raceway cover

to raceway base.

2-Gang Device Box (OFR48-2) and Device Plates (OFR47-B, OFR47-D, OFR47-R, OFR47-2A, OFR47-U,

OFR47-V, OFR47-U2A

4. Insert divider tabs in one of the three sets of mounting

bridges in the base. Select the set of bridges that is

appropriate for the layout of wires in the raceway.

2

6. Attach device box cover using (4)

#

8-32 round head screws.

If raceway is to extend beyond the device box, follow the following steps

for altering the device box to accept a second section of raceway.

7. Remove base extension from base.

This part is no longer needed.

8. Remove breakaway tab on end of divider.

9. Remove breakaway tab on end of cover. First

break corners as shown in 9A. Second twist the

center of the tab 9B until it breaks free.

10. Complete installation using steps 1 trough 6.

9A

9B

3

1. Insert device box connecting tabs into outer channels of

raceway base mounted to floor. Tighten (2) #8-32 screws

to secure.

2. Using #8 fasteners, install base of raceway directly on

top of existing floor covering. The screw type should be

appropriate for the type of floor, which the raceway is

being installed on.

3. Place wires in raceway base and attach raceway cover

to raceway base.

4-Gang Device Box (OFR48-4)

4. Insert divider tabs in one of the three sets of

mounting bridges in the base. Select the set of

bridges that is appropriate for the layout of wires in

the raceway.

4B. (CROSSOVER DIVIDER) (OFR48-4GX sold separately)

Attach crossover divider to base using (4) #8-32 round

head screws. End of tunnel must butt against raceway

base.

5. Mount the devices and device plates to the device box.

• For device plates used with NEMA standard devices (OFR47-D,

OFR47-R), mount as shown in 5A.

• For device plates, which mount communications and AV devices

(OFR47-2A, OFR47-U, OFR47-V, OFR47-U2A), remove break away

tabs as shown in 5B.

5A

5B

4

6. Attach device box cover using (4)

#8-32 round head screws.

If raceway is to extend beyond the device box, follow the following steps

for altering the device box to accept a second section of raceway.

7. Remove base extension from base.

This part is no longer needed.

8. Remove breakaway tab on end of divider.

9. Remove breakaway tab on end of cover. First

break corners as shown in 9A. Second twist the

center of the tab 9B until it breaks free.

10. Complete installation using steps 1 trough 6.

9A

9B

Page is loading ...

Legrand OFR Series Overfloor Raceway Device Boxes Operating instructions

Legrand OFR Series Overfloor Raceway Device Boxes Operating instructions

in other languages

Related papers

Other documents