11/16"
(17.5mm)
Drill 2-1/8" (54 mm) diameter
hole through door for HANDLESET.
Minimum
r
ecommended
d
istance
7/8"
(22mm)
Drill 2-1/8" (54 mm) diameter hole
t
hrough door for DEADBOLT.
1-3/4" (45 mm)
T
hick Door
C
ENTER MARK FOR:
1-3/8" (35 mm)
T
hick Door
1-3/4" (45 mm)
Thick Door
CENTER MARK FOR:
1-3/8" (35 mm)
Thick Door
Drill 1" (25.4 mm)
h
ole for
DEADBOLT latch.
C
heck door thickness
before drilling!
Drill 1" (25.4 mm) hole
f
or HANDLESET latch.
C
heck door thickness
before drilling!
5
-1/2"
(140 mm)
FOLD THIS LINE TO THE EDGE OF DOOR
FOLD THIS LINE TO THE EDGE OF DOOR
8-3/8"
(213 mm)
11"
(279 mm)
38" (965 mm)
From floor
(Suggested distance)
TEMPLATE FOR HANDLESET INSTALLATION
OUTSIDE SURFACE OF RIGHT HAND DOOR
Drill 5/16" (8 mm)
diameter hole
through door.
MEASURE YOUR HANDLESET
FOR THE CORRECT LENGTH.
2
3
/
8
2
3
/
4
2
3
/
8
2
3
/
4
Drill 5/16" (8 mm)
diameter hole
through door.
A
C
D
B
E
2-3/4” (70 mm) BACKSET
2-3/8” (60 mm) BACKSET
Drill 1/8" dia.
pilot holes for
xxx" long screws.
D
2-3/4” (70 mm) BACKSET
Hole Diameters:
A = 2-1/8”
(54 mm)
B = 1”
(25.4 mm)
C = 5/16”
(8 mm)
D = 2 1/8”
(54 mm)
E = 1”
(25.4 mm)
A
B
C
D
E
2-3/8” (60 mm) BACKSET
8-3/8" (213 mm)
Mark for SHOR
TER
HANDLESET
11" (279 mm) Mark for
LONG
ER HANDLESET
Hampton Products International Corp.
50 Icon
Foothill Ranch, CA 92610-3000
www.hamptonproducts.com
1-800-562-5625
Made in China
©
2007
Hampton Products International Corp.
999-00125 REVA 3/07
Template
C
enterline
38" (965 mm)
From floor
(Suggested distance)
Drill 1/8" dia.
pilot holes for
xxx" long screws.
D
Hole Diameters:
A
B
C
D
E
1-3/4" (45 mm)
Thick Door
C
ENTER MARK FOR:
1-3/8" (35 mm)
T
hick Door
1
-3/4" (45 mm)
T
hick Door
C
ENTER MARK FOR:
1-3/8" (35 mm)
Thick Door
D
rill 1" (25.4 mm)
h
ole for
DEADBOLT latch.
Check door thickness
before drilling!
D
2
3
/
8
2
3
/
4
2
3
/
8
2
3
/
4
2-3/8
2
-3/4
Drill 2-1/8" (54 mm)
diameter hole through
door for HANDLESET.
Minimum
r
ecommended
d
istance
Drill 2-1/8" (54 mm)
diameter hole through
door for DEADBOLT.
5-1/2"
(140 mm)
2-3/4” (70 mm) BACKSET
2-3/8” (60 mm) BACKSET
Drill 1" (25.4 mm)
hole for
H
ANDLESET latch.
Check door thickness
before drilling!
A
B
11/16"
(17.5mm)
7/8"
(22 mm)
FOLD THIS LINE TO THE EDGE OF DOOR FOLD THIS LINE TO THE EDGE OF DOOR
2-3/4” (70 mm) BACKSET
2-3/8” (60 mm) BACKSET
8-3/8"
(213 mm)
11"
(279 mm)
8-3/8" (213 mm) Mark for
SHOR
TER HANDLESET
11" (279 mm) Mark for
LONGER HANDLESET
Drill 5/16" (8 mm)
diameter hole through
door.
Drill 5/16" (8 mm) diameter
hole through door
.
MEASURE YOUR HANDLESET
FOR THE CORRECT LENGTH.
C
© 2007 HAMPTON PRODUCTS INTERNATIONAL
E
TEMPLATE FOR HANDLESET INSTALLATION
O
UTSIDE SURFACE OF LEFT HAND DOOR
A = 2-1/8”
(54 mm)
B = 1”
(25.4 mm)
C = 5/16”
(8 mm)
D = 2 1/8”
(54 mm)
E = 1”
(25.4 mm)
Template
C
enterline
/
