TP-LINK TE7WA730RE User manual

TL-WA730RE

150Mbps Wireless Range Extender

Rev: 1.0.0

1910010310

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized

modifications to this equipment. Such modifications could void the user’s authority to operate the

equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This device and its antenna must not be co-located or operating in conjunction with

any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only

Mobile Configurations. The antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

National restrictions

This device is intended for home and office use in all EU countries (and other countries following

the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country Restriction Reason/remark

Bulgaria None

General authorization required for outdoor use and

public service

France

Outdoor use limited to 10

mW e.i.r.p. within the band

2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz

band has been ongoing in recent years to allow current

relaxed regulation. Full implementation planned 2012

Italy None

If used outside of own premises, general authorization is

required

Luxembourg None

General authorization required for network and service

supply(not for spectrum)

Norway Implemented

This subsection does not apply for the geographical area

within a radius of 20 km from the centre of Ny-Ålesund

Russian Federation None Only for indoor applications

Note: Please don’t use the product outdoors in France.

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 150Mbps Wireless Range Extender

Model No.: TL-WA730RE

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical

regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC

The above product is in conformity with the following standards or other normative documents

ETSI EN 300 328 V1.7.1: 2006

ETSI EN 301 489-1 V1.8.1:2008& ETSI EN 301 489-17 V2.1.1:2009

EN60950-1:2006

Recommendation 1999/519/EC

EN62311:2008

Directives 2004/108/EC

The above product is in conformity with the following standards or other normative documents

EN 55022:2006 +A1:2007

EN 55024:1998+A1:2001+A2:2003

EN 61000-3-2:2006

EN 61000-3-3:1995+A1:2001+A2:2005

Directives 2006/95/EC

The above product is in conformity with the following standards or other normative documents

EN60950-1:2006

Directive（ErP） 2009/125/EC

Audio/Video, information and communication technology equipment- Environmentally conscious

design

EN62075:2008

Person is responsible for marking this declaration:

Yang Hongliang

Product Manager of International Business

TP-LINK TECHNOLOGIES CO., LTD.

South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan,

Shenzhen, P. R. China

CONTENTS

Package Contents....................................................................................................1

Conventions .............................................................................................................1

Overview of This Guide ...........................................................................................2

Chapter 1 Introduction...........................................................................................4

1.1 Product Overview.............................................................................................. 4

1.2 Main Features ................................................................................................... 4

1.3 Appearance....................................................................................................... 5

1.3.1 The Front Panel.................................................................................................5

1.3.2 The Rear Panel..................................................................................................6

Chapter 2 Hardware Installation ...........................................................................7

2.1 Before You Begin.............................................................................................. 7

2.2 Basic Requirements.......................................................................................... 7

2.3 Connecting the Device...................................................................................... 7

Chapter 3 Quick Installation Guide.......................................................................9

3.1 Configure the PC .............................................................................................. 9

3.2 Quick Setup .................................................................................................... 12

Chapter 4 Configure the Device..........................................................................17

4.1 Status.............................................................................................................. 17

4.2 Quick Setup .................................................................................................... 18

4.3 QSS ................................................................................................................ 18

4.4 Network........................................................................................................... 23

4.5 Wireless .......................................................................................................... 24

4.5.1 Wireless Settings.............................................................................................24

4.5.2 Wireless Security.............................................................................................27

4.5.3 Wireless MAC Filtering ....................................................................................32

4.5.4 Wireless Advanced..........................................................................................34

4.5.5 Throughput Monitor .........................................................................................35

4.5.6 Wireless Statistics............................................................................................36

4.6 DHCP.............................................................................................................. 37

4.6.1 DHCP Settings.................................................................................................38

4.6.2 DHCP Clients List............................................................................................39

4.6.3 Address Reservation .......................................................................................39

4.7 System Tools .................................................................................................. 40

4.7.1 SNMP ..............................................................................................................41

4.7.2 Diagnostic........................................................................................................42

4.7.3 Ping Watch Dog...............................................................................................44

Be sure to click the Save button to make your settings in operation. ..........................45

4.7.4 Firmware Upgrade...........................................................................................45

4.7.5 Factory Defaults...............................................................................................46

4.7.6 Backup & Restore............................................................................................46

4.7.7 Reboot .............................................................................................................47

4.7.8 Password.........................................................................................................48

4.7.9 System Log......................................................................................................48

Appendix A: Application Example........................................................................50

Appendix B: Factory Defaults...............................................................................53

Appendix C: Troubleshooting...............................................................................54

Appendix D: Specifications...................................................................................55

Appendix E: Glossary............................................................................................56

Package Contents

TL-WA730RE 150Mbps Wireless Range

Extender

Resource CD, including:

z This User Guide

z Other Helpful Information

Power Adapter for TL-WA730RE 150Mbps

Wireless Range Extender

Ethernet Cables

Quick Installation Guide

)

Note:

Make sure that the package contains the above items. If any of the listed items are damaged or

missing, please contact with your distributor.

Conventions

The AP or TL-WA730RE, or device mentioned in this User guide stands for 150Mbps Wireless

Range Extender without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may differ

from the actual situation. You can set the parameters according to your demand.

1

Overview of This Guide

Package Contents: Tells what are contained in the box.

Chapter 1 Introduction:

Gives an introduction for the TL-WA730RE 150Mbps

Wireless Range Extender.

1.1 Product Overview:

Introduces advantages of using this AP.

1.2 Main Feature:

Introduces main features and their benefits.

1.3 Appearance:

Gives descriptions of LEDs, ports and buttons on the

front and rear panel.

Chapter 2 Hardware Installation:

Tells how to connect the AP and the requirements.

2.1 Before You Begin:

Gives suggestions for better performance of the wireless

network.

2.2 Basic Requirement:

Introduces some basic requirements for successful

installation and long-term use

2.3 Connecting the Device:

Introduces steps to connect the AP.

Chapter3 Quick Installation Guide:

3.1 C

Tells how to configure the IP address of your PC and

manage the device easily with a Web-based utility.

onfigure the PC:

3.2 Q

Gives information about how to configure your PC to

communicate with the AP

uick Setup: Gives information about how to log on to the web-based

management page and configure the TL-WA730RE

150Mbps Wireless Range Extender easily with a

Web-based utility.

Chapter 4 Configure the Device:

Tells how to configure the AP via the web-based

management page.

4.1 Status:

Gives information about the AP’s current configuration.

4.2 Quick Setup:

Refer to section 3.2 Quick Setup to configure the

TL-WA730RE easily with a Web-based utility.

4.3 QSS:

Guides how to add a new wireless device to an existing

network quickly.

4.4 Network:

Tells how to configure the IP parameters of AP.

4.5 Wireless: Guides to establish the wireless network in different

wireless modes and deploy the security features

appropriate to your needs.

2

4.6 DHCP: Introduces how to set your AP to be a DHCP server so

that the AP will automatically assign an IP address for

your PC.

4.7 System Tools: Provides some useful tools.

3

TL-WA730RE 150Mbps Wireless Range Extender User Guide

4

Chapter 1 Introduction

Thank you for choosing the TL-WA730RE 150Mbps Wireless Range Extender.

1.1 Product Overview

The TL-WA730RE 150Mbps Wireless Range Extender is dedicated to Small Office/Home Office

(SOHO) wireless network solutions. It can relay signal between its stations and the root AP for

greater wireless range easily and quickly. Increased mobility and the absence of cabling will be

beneficial for your network.

With using IEEE 802.11n wireless technology, your device can transmit wireless data at the rate of

up to 150Mbps. With multiple protection measures, including SSID broadcast control and wireless

LAN 64/128/152-bit WEP encryption, WiFi protected Access (WPA2-PSK, WPA-PSK), as well as

advanced Firewall protections, the TL-WA730RE 150Mbps Wireless Range Extender delivers

complete data privacy.

The TL-WA730RE 150Mbps Wireless Range Extender is easy to configure and manage with the

Utility provided. Besides, the Auto-repeater function can be used to connect the device with a

Router around without any cable. For more information, please look through this User Guide.

1.2 Main Features

Features Benefits

Make use of IEEE 802.11n wireless technology Allows your device to transmit wireless data at

the rate of up to 150Mbps

Provides multiple encryption security Types

including: 64/128/152-bit WEP WPA/WPA2

WPA-PSK/WPA2-PSK

Secures your data while the data packets are

being transmitted

Supports Built-in DHCP server Supports dynamic IP address distributing

Supports MAC address filtering Allows you to control the access rights of the

wireless stations, depending on the stations'

MAC addresses

Supports multiple operating modes including:

z Range Extender

Makes the AP an ideal solution for your wireless

local area network

Relays signal between its stations and the root

AP for greater wireless range

z Access Point Allows wireless stations to access and you can

create a wireless local area network.

Supports Firmware Upgrade You can easily upgrade the firmware to the

latest version through the web-based

management page

TL-WA730RE 150Mbps Wireless Range Extender User Guide

1.3 Appearance

1.3.1 The Front Panel

Figure 1-1

The front panel of the TL-WA730RE consists of several LED indicators, which is designed to

indicate connections. View from left to right, Table 1-1 describes the LEDs on the front panel of the

device.

LED Explanation

Name Status Indication

Off No Power

Power

On Power on

Off The device has a system error

On

The device is initialising

System

Flashing

The device is working properly

Off

There is no device linked to the corresponding port

On

There is a device linked to the corresponding port but no activity

LAN

Flashing

There is an active device linked to the corresponding port

Off

The Wireless function is disabled

WLAN

Flashing

The Wireless function is enabled

On

The Range Extender has connected the Router successfully

Flashing

The Range Extender is connecting the Router

RANGE

EXTENDER

Off

The Range Extender has not connected any Router yet

Table 1-1

5

TL-WA730RE 150Mbps Wireless Range Extender User Guide

1.3.2 The Rear Panel

Figure 1-2

Viewed from left to right, the following parts are located on the rear panel of TL-WA730RE.

POWER: The power port connects to the power adapter provided with the TL-WA730RE 150Mbps

Wireless Range Extender.

LAN: One LAN 10/100Mbps RJ45 port connects to a network device, such as a switch or a router.

RESET: The Reset button is used to restore the AP’s factory default settings. There are two ways

to reset the Access Point’s factory defaults:

z Method one: With the AP powered on, use a pin to press and hold the Reset button (about 5

seconds) until the System LED becomes quick-flash from slow-flash. And then release the

button and wait the router to reboot to its factory default settings.

z Method two: Restore the default settings from “System Tools > Factory Defaults” of the

Modem's Web-based management page.

Wireless antenna: The external antenna is used to transmit and receive wireless data.

)

Note:

Ensure the Range Extender is powered on before it restarts completely.

6

TL-WA730RE 150Mbps Wireless Range Extender User Guide

Chapter 2 Hardware Installation

2.1 Before You Begin

Please read this User Guide carefully before installing and using the equipment. The operating

distance range of your wireless connection can vary significantly depending on the physical

position of the wireless devices. Factors that can weaken signals by getting in the way of your

network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary base

on the types of materials and background RF (radio frequency) noise in your home or office.

For best performance of your wireless network, you are suggested to:

1) Avoid redundant obstacles and interference between the wireless devices.

2) Keep your AP away from appliances with a strong electric field or magnetic field, such as a

microwave oven or refrigerator.

Place the AP near the center of the area in which your computers operates.

2.2 Basic Requirements

z Use only the power adapter provided with your AP

z The electrical outlet shall be installed near the device and shall be easily accessible

z Place your AP in a well ventilated place far from direct sunlight, any heater or heating vent

z Leave at least 2 inches (5cm) space around the device for heat dissipation

z Turn off your AP and unplug the power adapter in a lighting storm to avoid damage

z Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or

above

z Operating temperature: 0℃~40℃ (32℉~104℉)

z Operating Humidity: 10%~90%RH, Non-condensing

2.3 Connecting the Device

Figure 2-1 is an example of the typical application of TL-WA730RE in the infrastructure network.

An Infrastructure network contains an access point or a wireless router.

7

TL-WA730RE 150Mbps Wireless Range Extender User Guide

Figure 2-1 The Example of Infrastructure Network Incorporating the TL-WA730RE

To establish a typical connection of the AP, please take the following steps:

1. Connect the Cable or DSL modem to a Router.

2. Locate an optimum location for the AP. The best place is usually near the center of the area in

which your PC(s) will wirelessly connect.

3. Adjust the direction of the antenna. Normally, upright is a good direction.

4. Connect the Ethernet Broadband Router to the TL-WA730RE Access Point. Power on the AP.

5. Then you can connect a desktop PC or laptop to your network. (Make sure your computer or

laptop is equipped with a Wireless Adapter.)

)

Note:

If you are not so clear about how to connect your devices to the network, please refer to Appendix

A Application Example.

8

TL-WA730RE 150Mbps Wireless Range Extender User Guide

Chapter 3 Quick Installation Guide

This chapter will guide you to configure your PC to communicate with the AP and to configure and

manage the TL-WA730RE 150Mbps Wireless Range Extender easily with a Web-based utility.

3.1 Configure the PC

The wireless adapter-equipped computers in your network must be in the same IP Address range

without overlap with each other. Manually configure the IP address as 192.168.1.* (* is any

integer between 1 to 253), and the Subnet mask as 255.255.255.0 for your PC by following the

instructions below.

Connect the local PCs to the LAN ports on the AP and configure the IP address manually for your

PCs.

1. Click Start (in the lower left corner of the screen), right-click My Network Connections and

choose Properties.

Figure 3-1

2. On the My Network Connections window shown as Figure 3-2 below, right-click LAN (Local

Area Connection) and choose Properties.

9

TL-WA730RE 150Mbps Wireless Range Extender User Guide

Figure 3-2

3. In the General tab of Internet Protocol (TCP/IP) Properties window, highlight Internet

Protocol (TCP/IP) and click Properties.

Figure 3-3

10

TL-WA730RE 150Mbps Wireless Range Extender User Guide

4. Configure the IP address manually.

1) Select Use the following IP address.

2) Enter 192.168.1.* (* is any integer between 1 to 253) into the IP address filed,

255.255.255.0 into the Subnet mask filed.

3) Click OK to keep your settings.

Figure 3-4

5. Verify the network connection between your PC and the AP via the Ping command. The

following example is in Windows XP Operating System.

1) Click Start > Run tab. Enter cmd in the filed and click OK.

2) Type ping 192.168.1.254 on the screen that displays and then press Enter.

If the result displayed is similar to that shown in Figure 3-5 below, the connection

between your PC and the AP has been successfully established.

Figure 3-5

11

TL-WA730RE 150Mbps Wireless Range Extender User Guide

If the result displayed is similar to that shown in Figure 3-6 below, it means that your PC

has not connected to the AP.

Figure 3-6

Please check following these steps:

a) Check to see if your PC and the AP are right connected. The LED of LAN port which

you link to on the device and the LED on your PC’s adapter should be lit up.

b) Make sure the TCP/IP for your PC is right configured. If the AP’s IP address is

192.168.1.254, your PC’s IP address must be within the range of 192.168.1.1 ~

192.168.1.253.

3.2 Quick Setup

With a Web-based utility, it is easy to configure and manage the TL-WA730RE 150Mbps Wireless

Range Extender. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with

a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.

1. To access the configuration utility, open a web-browser and type in the default address

http://192.168.1.254 in the address field of the browser.

Figure 3-7 Login to the AP

After a moment, a login window will appear, similar to the Figure 3-8. Enter admin for the

User Name and Password (both in lower case letters). Then click OK or press Enter.

Figure 3-8 Login Windows

12

TL-WA730RE 150Mbps Wireless Range Extender User Guide

)

Note:

If the above screen does not prompt, it means that your web-browser has been set to a proxy.

Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that

appears, cancel the Using Proxy checkbox, and click OK to finish it.

2. After successfully logging in, click the Quick Setup menu to quickly configure your AP and

the following figure will display. Click Next to continue.

Figure 3-9 Quick Setup

3. And then Wireless page will appear shown in Figure 3-10. There are two Operation Modes,

including Range Extender and Access Point. The available setting options are different in

different operation modes, and they are explained below.

Figure 3-10 Quick Setup - Wireless

A. When you choose Range Extender, take the following steps:

1） Click Search on the Wireless page shown as Figure 3-10 , and then AP List page will appear,

shown in Figure 3-11.

13

Page is loading ...

TP-LINK TE7WA730RE User manual

This manual is also suitable for

TP-LINK TE7WA730RE User manual

Related papers

Other documents