Samsung HG28EC690AB Installation guide

Brand: Samsung

Model: HG28EC690AB

Category: LED TVs

Type: Installation guide

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please

www.samsung.com/register

Model Serial No.

LED TV

Installation manual

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product

appearance. Product design and specifications may be changed without notice.

Instruction

This TV is provided with interactive functionality through a set-back box (SBB/STB) connected to the TV, and with other TVs in a

computer-controlled system for hotels and other hospitality businesses.

Interactive: When the TV is powered-up initially, it sends a command to identify the SBB/STB; if identified, theTV switches to

ONLINE mode and full control is through the SBB/STB.

If the TV is in ONLINE mode, it stops receiving IR(Samsung remote) commands and acts according to interface protocol.

Stand-Alone: If SBB/STB is not identified, the TV should be switched to STAND-ALONE mode with restricted operation.

Operational Modes

When this TV (in Hotel mode) is operated with a SBB/STB, it is in one of two states :

• ONLINE or STAND-ALONE. In the STAND-ALONE state, the TV will act as a Hotel TV, but without active communication.

This is to prevent guests from trying to cheat the system by disconnecting the SBB/STB.

Power

Hotel TV

Online Mode

Poll Rate 20/sec

Stand-alone

Mode

Hotel Mode On

SBB/STB Online if

one success within

10 attempts

SBB/STB

Online-10

consecutive

fails

SBB/STB

Status-

Attempt

every 2secs

To set the details for Stand-alone or interactive mode, refer to pages 22-25(Setting the hotel option data : Stand-alone

mode and Interactive mode)

• Some operations may be restricted to prevents guests from "cheating" the TV system.

• No main menu(Interactive mode) or Channel Menu, Plug & Play in Main Menu (Stand-Alone mode)

• Limited Volume and Panel key lock or unlock

Still image warning

Avoid displaying still images (like jpeg picture files) or still image element (like TV Program logo, panorama or 4:3 image format,

stock or news bar at screen bottom etc.) on the screen. Constant displaying of still picture can cause uneven wear of screen

phosphor, which will affect image quality. To reduce risk of this effect, please follow below recommendations:

• Avoid displaying the same TV channel for long periods.

• Always try do display any image on full screen, use TV set picture format menu for best possible match.

• Reduce brightness and contrast values to minimum required to achieve desired picture quality, exceeded values may speed

up the burnout process.

• Frequently use all TV features designed to reduce image retention and screen burnout. Refer to the relevant user manual

section for details.

Securing the Installation Space

Keep required distances between the product and other objects (e.g. walls) to ensure proper ventilation.

Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature.

✎

When using a stand or wall-mount, use parts provided by Samsung Electronics only.

• Using parts provided by another manufacturer may result in a problem with the product or injuries due to the product falling.

✎

The appearance may differ, depending on the product.

Installation with a stand. Installation with a wall-mount.

10 cm10 cm

10 cm

10 cm10 cm

10 cm

Contents

ENGLISH

English

y Instruction ............................................................................................................................................................ 2

y Operational Modes ............................................................................................................................................... 2

y Still image warning ............................................................................................................................................... 2

y Securing the Installation Space............................................................................................................................. 2

y Accessories.......................................................................................................................................................... 4

y Installing the LED TV Stand .................................................................................................................................. 5

y Assembling the swivel (32 inch TVs or larger) ....................................................................................................... 7

y Viewing the Connection Panel .............................................................................................................................. 9

y TV Controller ...................................................................................................................................................... 12

y Viewing the Remote Control ............................................................................................................................... 13

y Connecting the TV with SBB .............................................................................................................................. 14

y Connecting the Bathroom Speakers ................................................................................................................... 16

y Connecting the MediaHub HD ............................................................................................................................ 18

y Connecting the RJP (Remote Jack Pack) ........................................................................................................... 19

y Connecting to a COMMON INTERFACE slot (Your TV viewing Card Slot) ........................................................... 21

y Setting the Hotel Option Data ............................................................................................................................. 22

y Installing the Wall Mount ..................................................................................................................................... 60

y Securing the TV to the Wall ................................................................................................................................ 61

y Anti-theft Kensington Lock ................................................................................................................................. 61

y Speciﬁcations ..................................................................................................................................................... 62

y Dimensions ........................................................................................................................................................ 63

English

Accessories

✎ Please make sure the following items are included with your LED TV. If any items are missing, contact your dealer.

✎ The items’ colour and shapes may vary depending on the model.

• Remote Control & Batteries (AAA x 2)

• Quick Set up Guide

• CI Card Adapter

• Hotel Mount Kit

• Power Cord / Data Cable

• Owner’s Instructions

Safety Guide (Not available in all locations)

• Cable Holder

✎ The stand and stand screw may not be included, depending on the model.

✎ The Data Cable may not be included, depending on the SI Vendor.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic

accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste

at the end of their working life. To prevent possible harm to the environment or human health from

uncontrolled waste disposal, please separate these items from other types of waste and recycle them

responsibly to promote the sustainable reuse of material resources. Household users should contact either

the retailer where they purchased this product, or their local government office, for details of where and

how they can take these items for environmentally safe recycling. Business users should contact their

supplier and check the terms and conditions of the purchase contract. This product and its electronic

accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return

systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not

be disposed of with other household waste at the end of their working life. Where marked, the chemical

symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference

levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm

to human health or the environment. To protect natural resources and to promote material reuse, please

separate batteries from other types of waste and recycle them through your local, free battery return

system.

English

Installing the LED TV Stand

The 32” and larger LED TVs have swivel stands. You can set these stands so that the TVs swivel 20 degrees left and

right or 90 degrees left and right.

Stand Components

When installing the stand, use the provided components and parts.

28"

32" ~ 55"

1 EA

28"

32"

40" ~ 55"

28" ~ 32"

40" ~ 55"

x7 (M4 X L12)

x8 (M4 X L12)

• Stand • Guide Stand • Screws

HG28EC690

Tight the bottom of the screw ﬁrst, and stow the upper side

of screw last.

When the declination happened, try reassemble it

category.

(M4 X L12)

✎ Place a soft cloth over the table to protect the TV, and then place the TV

on the cloth screen-side down.

✎ Insert the Stand Guide into the slot on the bottom of the TV.

✎ Slide and assemble it to the end line in the direction of arrow.

3-1 3-2

✎ Progress the assembly of screw in the manual’s order.

✎ Make sure to assembling stand guide attached on the TV.

2-32-1 2-2

1-1

1-3

(M4 X L12)

1-2

English

HG32EC690 / HG40EC690 / HG48EC690 / HG55EC690

Tight the bottom of the screw ﬁrst, and stow the upper side of screw last.

When the declination happened, try reassemble it

category.

✎ Place a soft cloth over the table to protect the TV, and then place

the TV on the cloth screen-side down.

✎ Insert the Stand Guide into the slot on the bottom of the TV.

✎ Slide and assemble it to the end line in the direction of arrow.

3-1

3-2

✎ Progress the assembly of screw in

the manual’s order.

✎ Make sure to assembling stand guide attached on the TV.

2-32-1 2-2

(M4 X L12)

1-1

1-3

1-2

32"

x3 (M4 X L12)

40" ~ 55"

x4 (M4 X L12)

✎

NOTE

y Make sure to distinguish between the front and back of each component when assembling them.

y Make sure that at least two persons lift and move the TV.

English

Assembling the swivel (32 inch TVs or larger)

] WARNING: If you conﬁgure the TV to swivel, you must attach it securely to the ﬂoor, a desk, a dresser top, etc. as

described in the installation instructions.

The 32” and larger LED TVs have swivel stands. You can conﬁgure these stands so that the TVs swivel 20 degrees left and

right, 60 degrees left and right, or 90 degrees left and right using the BRACKET HOLDER SWIVEL.

¦ 20° Swivel

To conﬁgure the TV so that it swivels 20° left and right, insert the prong on the bottom of the stand through the curved hole

in the Bracket Holder Swivel marked 20°. Then, ﬁx the Bracket Holder Swivel to the stand using the three supplied screws as

shown below.

¦ 60° Swivel

To conﬁgure the TV so that it swivels 60° left and right, insert the prong on the bottom of the stand through the curved hole

in the Bracket Holder Swivel marked 60°. Then, ﬁx the Bracket Holder Swivel to the stand using the three supplied screws as

shown below.

¦ 90° Swivel

To conﬁgure the TV so that it swivels 90° left and right, remove the Bracket Holder Swivel, and then screw the three supplied

screws into the stand as shown below.

English

¦ Hotel Mount Kit

Afﬁx the stand to a ﬂat surface such as a

dresser top, desk top, or entertainment center as

shown.

[

WARNING: To prevent injury, you must attach this TV securely to the ﬂoor, a table, a dresser top, etc. with

the Hotel Mount Kit as described in these instructions.

Short Bolt (2EA) Long Bolt (2EA) Nut (2EA) Washer (2EA)

Bolt + Nut

Top

Bottom

English

Viewing the Connection Panel

✎ Whenever you connect an external device to your TV, make sure that power on the unit is turned off.

✎ When connecting an external device, match the colour of the connection terminal to the cable.

HG32EC690**

HG40EC690**

HG48EC690**

HG55EC690**

HG28EC690**

2 3

$ #

2 3

$ #

English

1 AV IN

– Connect audio cables to "R-AUDIO-L" on your TV and the other ends to corresponding audio out jacks on an

A/V device.

– Connect RCA audio cables (optional) to "R - AUDIO - L" on the rear of the TV set and the other ends to

corresponding audio out jacks on the external device.

– When connecting to AV IN, the color of the AV IN [Y/VIDEO] jack (Green) does not match the color of the video

cable (Yellow).

2 USB (5V 0.5A)

USB (HDD/1.0A) / CLONING

– Connector for software upgrades and Media Play, etc.

– Service connection.

3 HDMI IN 1, 2(DVI), 3(ARC): Connects to the HDMI jack of a device with an HDMI output.

✎ No sound connection is needed for an HDMI-HDMI connection. HDMI connections carry both audio and video.

✎ Use the HDMI IN 2(DVI) jack for a DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI

adapter (DVI to HDMI) for the video connection and the PC/DVI AUDIO IN jacks for audio.

4 ANT IN (SATELLITE), (AIR/CABLE)

– To view television channels correctly, the TV must receive a signal from one of the following sources:

– An outdoor antenna / A cable television system

5 HEADPHONE JACK: Headphones may be connected to the headphone jack on your TV. While the headphones are

connected, the sound from the built-in speakers is disabled.

6 HP-ID: Connect the cable to HP-ID and Headphone Jack simultaneously and connect it to separated Headphone

Box. See page 17. When connecting Headphone to Headphone Box, it works same as Headphone function.

Display Modes

You can also select one of the standard resolutions listed in the Resolution column. The TV will automatically adjust to

the resolution you choose.

After connecting a computer to the TV, set the screen resolution for the TV on the computer. The optimal resolution is

1920 x 1080 @ 60 Hz. If it is set to any other than in the table below, the TV may display nothing. Set the resolution

properly, referring to the user guide of the computer or its graphic card.

The resolutions in the table are recommended.

✎ Optimal resolution is 1366 X 768 @ 60 Hz.

Mode Resolution

Horizontal Frequency

(KHz)

Vertical Frequency

(Hz)

Pixel Clock Frequency

(MHz)

Sync Polarity

(H / V)

IBM

640 x 350

720 x 400

31.469

70.086

70.087

25.175

28.322

+/-

-/+

MAC

640 x 480

832 x 624

35.000

49.726

66.667

74.551

30.240

57.284

-/-

VESA CVT

720 x 576

1280 x 720

35.910

56.456

59.950

74.777

32.750

95.750

-/+

VESA DMT

640 x 480

800 x 600

1024 x 768

1280 x 720

1366 x 768

31.469

37.500

37.861

37.879

46.875

48.077

48.363

56.476

60.023

45.000

47.712

59.940

75.000

72.809

60.317

75.000

72.188

60.004

70.069

75.029

60.000

60.015

25.175

31.500

40.000

49.500

50.000

65.000

75.000

78.750

74.250

85.500

-/-

+/+

-/-

+/+

VESA GTF 1280 x 720 52.500 70.000 89.040 -/+

English

✎ Optimal resolution is 1920 X 1080 @ 60 Hz.

Mode Resolution

Horizontal Frequency

(KHz)

Vertical Frequency

(Hz)

Pixel Clock Frequency

(MHz)

Sync Polarity

(H / V)

IBM 720 x 400 31.469 70.087 28.322 -/+

MAC

640 x 480

832 x 624

1152 x 870

35.000

49.726

68.681

66.667

74.551

75.062

30.240

57.284

100.000

-/-

VESA DMT

640 x 480

800 x 600

1024 x 768

1152 x 864

1280 x 1024

1280 x 720

1280 x 800

1280 x 960

1366 x 768

1440 x 900

1600 x 900RB

1680 x 1050

1920 x 1080

31.469

37.861

37.500

37.879

48.077

46.875

48.363

56.476

60.023

67.500

63.981

79.976

45.000

49.702

60.000

47.712

55.935

60.000

65.290

67.500

59.940

72.809

75.000

60.317

72.188

75.000

60.004

70.069

75.029

75.000

60.020

75.025

60.000

59.810

60.000

60.015

59.887

60.000

59.954

60.000

25.175

31.500

40.000

50.000

49.500

65.000

75.000

78.750

108.000

135.000

74.250

83.500

108.000

85.500

106.500

108.000

146.250

148.500

-/-

+/+

-/-

+/+

-/+

+/+

-/+

+/+

-/+

+/+

✎ When using an HDMI/DVI cable connection, you must use the HDMI IN 2 (DVI) jack.

✎ The interlace mode is not supported.

✎ The set might operate abnormally if a non-standard video format is selected.

✎ Separate and Composite modes are supported. SOG is not supported.

7 RJP: This port is an RJP (Remote Jack Pack) communication port that enables connecting different devices to

additional modules to improve device use and convenience.

8 PC/ DVI AUDIO IN: Connects to the audio input jacks on an Ampliﬁer/Home Theater.

9 VOL-CTRL: Used to control the volume of the Bathroom speaker. Connect the Bathroom Wall Box and the

VOLCTRL port.

0 VARIABLE AUDIO OUT: Used for the audio output to the Bathroom speaker. Connect the Bathroom Wall Box and

the Variable port (RCA).

! CLOCK: Set the time after connecting the cable of the External Clock to Clock jack. You can use the External Clock

Display function.

@ DATA

– Used to support data communication between the TV and the SBB.

– Connects using RJ-12 TV type plugs.

PC IN: Connect to the video output jack on your computer.

LAN: Connect to a wired LAN using CAT 7 cable.

English

TV Controller

TV Controller is a multi directional button that helps navigate without using the remote control.

✎ Some functions which require a PIN code may not be available.

✎ The product colour and shape may vary, depending on the model.

✎ Exits the menu when pressing the controller for more than 1 second.

✎ When selecting the function by moving the controller to the up/down/left/right directions, do not press the controller.

If the controller is used ﬁrst, you cannot operate it to move the up/down/left/right directions.

Power on Turn the TV on by pressing the controller in standby mode.

Adjusting the volume Adjust the volume by moving the controller from side to side when the power is

on.

Selecting a channel Select a channel by moving the controller up and down when the power is on.

Using the function menu Press the controller when the power is on and the function menu appears. If you

press it again, the function menu screen disappears.

Using the Menu

Selects the MENU(m) by moving the controller in the function menu screen. The

OSD(On Screen Display) of your TV’s feature appears.

Selecting the Source

Selects the Source(s) by moving the controller in the function menu screen.

The Source list screen appears.

Selecting the SMART

HUB ( ™ )

With the Function menu visible, select SMART HUB (™) by moving the Controller

upwards. The SMART HUB main screen appears. Select an application by

moving the Controller, and then pressing the Controller.

Power Off

Selects the Power Off(P) to turn the TV off by moving the controller in the

function menu screen.

✎ To close the Menu, SMART HUB, or Source, press the Controller for more than 1 second.

Standby mode

Do not leave your TV in standby mode for long periods of time a small amount of electric power is still consumed even

when the power button is such as when on holiday. off. It is best to unplug the power cord.

TV Controller

Function menu

Remote control sensor

The image is drawn by facing

the front side of the TV.

English

Viewing the Remote Control

✎ This remote control has Braille points on the

Power

Channel

, and Volume buttons and can be used by visually

impaired persons.

GUIDE

CONTENT

CLOCK

ALARM

AB CD

ALARM

SUBT.

CLOCK

GUIDE

CONTENT

HOME

CH LIST

TTX/MIX

Turns the TV on and off.

Have direct access to channels

Alternately selects Teletext, Double or Mix.

Adjust the volume.

Display channel list on the screen.

Display the main on-screen menu.

Quickly select frequently used functions.

Select on-screen menu items and

change menu values.

Return to the previous menu.

Buttons in the Channel list, Contents

Home menu, etc.

Use these buttons in the Contents

Home.

Display and select available video sources.

Electronic Programme Guide (EPG) display.

Cut off the sound temporarily.

Change channels.

Switch to the HOME Screen.

View the Contents Home.

Press to display information on the TV

screen.

CLOCK: When you press INFO key

in standby mode, TV screen displays

the time.

Exit the menu.

ALARM: Enter the hour you want the TV

to turn on.

W: Turns the 3D image on or off. ( Not

available )

SUBT.: Displays digital subtitles.

' : Stop.

English

Connecting the TV with SBB

1. Connect the D ATA jack of the TV to the [ETH MODEM] jack of the STB (SBB) with the Data cable.

✎ Use data communication.

ETH MODEM

TV Rear Panel

Data Cable

Installing batteries (Battery size: AAA)

✎ NOTE

• Use the remote control within 7m of the TV.

• Bright light may affect the performance of the remote control. Avoid using nearby special ﬂuorescent light or neon

signs.

• The colour and shape may vary depending on the model.

• Remote control button 'HOME' & '3D' are not supported. When pressing these buttons, the TV unit does not

respond.

English

¦ List of Vendors and Compatible Data Cables Supplied with the TV

• Conﬁrm that you are using the correct data cable for your vendor. Refer to the code label on the data cables.

English

Connecting the Bathroom Speakers

You can connect the Bathroom Speakers using the following method.

¦ Connecting through the Variable Output (available without an external ampliﬁer)

1. Connect the VARIABLE AUDIO OUT port of the TV to the Bathroom Wall Speakers of the hotel.

Speaker +

Speaker -

N/C

2. Connect the VOL-CTRL jack of the TV to the Volume Control Box Switch port on the Bathroom Wall of the hotel.

✎ The maximum speaker output is 4W, 8Ω.

✎ The VARIABLE AUDIO OUT port supports MONO sound out only.

• Installing the Volume Control

– If you conﬁgure the Volume Control Box as shown in the ﬁgure, you can control the volume of the bathroom

speakers.

– The jack that connects the Volume Control Box to the TV is a 3.5mm normal Phone jack.

– Volume Control Box switch is a Tact switch.

✎ Setting the Sub AMP Mode

– 0: Turns the Sub AMP function off (PWM off).

– 1: Determines the Sub volume according to the main volume control. the sub volume is determined according to

the Power On Volume, the Min Volume, and the Max Volume values of Hotel Mode.

– 2: Determines the volume according to the bathroom control panel setting.

• Variable Output Port Speciﬁcations

– Speaker Wire: Use speaker cable no more than 82 feet (25m) in length.

Volume Control Box

VOL - DOWN

( White 1 )

VOL - UP

( Black /Red 2 )

GND

( Shield Wire 3 )

VOL +

VOL

VOL+

VOL

TV Rear Panel

Volume Control Box

Speaker

VOL+

VOL

English

¦ Audio Loop In

An additional Headphone Box can be installed on a bed or business desk for added convenience. The installation

procedures are given below.

• Detailed Drawing of the Headphone Box.

TV Headphones jack

Whitewire (Audio-L)

Shield Wire

TV HP-ID jack

Red wire + White wire

Red Wire (Audio-R)

Shield wire

HEADPHON BOX

TV Rear Panel

Headphone Box

English

Connecting the MediaHub HD

Output to any external source connected to MediaHub HD on the hotel desk.

1. Connect the RJP port of the TV and the RS/232 port of the MediaHub HD.

2. Connect the HDMI IN 1, 2(DVI) or 3 (ARC) port of the TV and the HDMI port of the MediaHub HD.

• MediaHub HD

– The MediaHub HD is a hardware module that has different Audio Video inputs (A/V, Audio, PC, HDMI and USB)

and corresponding outputs. The corresponding output sources connect from MediaHub to the TV. MediaHub

communicates with the TV via RS232. Hot Plug & Play is a function that allows hotel guests to connect an

external source to the MediaHub. MediaHub communicates with the TV by sending messages regarding Active/

Inactive sources. The TV switches to the Active external source.

– You have to connect the HDMI of the MediaHub to the HDMI IN 2(DVI) port of the TV.

– When the TV is on, connect the TV and the RJP within 10 seconds.

• Special features

– PIP

– Auto Detection

HDMI

USB RS/232

TV Rear Panel

MediaHub HD Rear

HDMI cable

RS-232 Data Cable

English

Connecting the RJP (Remote Jack Pack)

Output to any external source connected to RJP on the hotel desk.

1. Connect the PC IN / PC/DVI AUDIO IN port of the TV to the PC/AUDIO port of the RJP.

2. Connect the AV IN [VIDEO]/[L-AUDIO-R] port of the TV to the VIDEO port of the RJP.

3. Connect the AV IN [VIDEO] port of the TV to the VIDEO port of the RJP.

4. Connect the HDMI IN 1, 2(DVI) or 3 (ARC) port of the TV and the HDMI port of the RJP.

5. Connect the RJP port of the TV and the RS/232 port of the RJP.

✎ The RJP (Remote Jack Pack) compatible with this Samsung TV is TeleAdapt TA-7610, TA-7650 (HD) and TA-

7660 (HD Plus).

• R

JP (Remote Jack Pack): RJP stands for Remote Jack Pack. The RJP is a hardware module that has different Audio

Video inputs (A/V, Audio, PC and HDMI) and corresponding outputs. The corresponding output sources are con-

nected from RJP to TV. The RJP communicates with the TV via RS232. Hot Plug & Play is a function that allows hotel

guests to connect an external source to the RJP. The RJP communicates with the TV by sending messages regarding

Active/Inactive sources. The TV will switch to the Active external source according to the priority set by the User.

✎ You can select HDMI IN 1, 2(DVI) or 3(ARC) and AV IN for connecting RJP.

✎ When the TV is on, connect the TV and the RJP within 10 seconds.

USB HDMI VIDEO

AUDIO AUDIO/PC

RS/232

TV Rear Panel

RJP Rear

D-sub / PC Audio cable

2 Audio Cable

3 Video Cable

4 HDMI cable

English

• The RJP can be returned to the factory default settings by pressing the A/V and HDMI buttons simultaneously for 10

seconds. All LEDs blink 5 times to acknowledge that this has been ﬁnished.

• The RJP will automatically turn off any LEDs after 5 minutes to avoid unnecessary light pollution in the hotel room.

The LEDs that were turned off will turn on again if the guest touches any of the buttons and the 5 minute timer will

restart. If the guest then touches another source button, the TV will change to the selected source and the corre-

sponding LED will be lit.

• After an RJP Reset or a TV Power OFF/ON, it takes approx. 10 seconds to establish communications between the

TV and the RJP.

• The following table shows the approximate time in seconds to switch from the TV to the input source, based on the

priority.

✎ Scenario 1: When no inputs are connected.

Source To Connect

AV 2 Sec

PC 0.7 Sec

HDMI 3.9 Sec

✎ Scenario 2: When two or more inputs are connected and an Input source is disconnected and then reconnected.

Source Disconnect To Connect Total

AV 4.5 Sec 2 Sec 6.5 Sec

PC 0.7 Sec 0.7 Sec 1.4 Sec

HDMI 3.9 Sec 3.9 Sec 7.8 Sec

✎ E.g. If the RJP has all its live sources AV, PC and HDMI connected, AV is viewed as the highest priority. If the RJP

is in HDMI mode, and a guest removes and reconnects the AV, the minimum time required to switch to the AV is

6.5 seconds.

• To connect audio (Ipod or Mp3), Music mode should be ON and Jack Ident detect should be OFF.

• A/V, PC and HDMI input sources are supported.

Page is loading ...

Samsung HG28EC690AB Installation guide

Brand: Samsung

Model: HG28EC690AB

Category: LED TVs

Type: Installation guide

Download PDF

report

Samsung HG28EC690AB Installation guide

Samsung HG28EC690AB Installation guide

Related papers

Other documents