AUNE S2 User manual

HEADPHONE AMP

s

2

INTRODUCTION 2

UNPACK

HIGHLIGHTS

NOTES 3

CAUTION.....................................3

ICONS.......................................3

DEVICE LAYOUT 4

FRONT PANEL.................................4

REAR PANEL..................................4

OPERATING INSTRUCTION 5

HEADPHONE AMP ..............................5

USE WITH OTHER DEVICE......................5

AFTER-SALE SERVICE 6

GENERAL............................ ........2

......................................2

..................................2

CONTENT

1

2

3

4

5

1

Copyright

Aune does not assume any responsibility for errors or omissions in this document or make

any commitment to update the information contained herein.

3

2

Situations that temperature is too high 40℃ or

too low (- 5℃) or humidity.

Avoid impact or place heavy objects on it.

Avoid any foreign matter inside the devic e.

( )

Avoid any chemicals like Benzene or Diluents.

Avoid direct sunlight or any heat sources.

Avoid magnetic dusty,do not disassemble or

modify.

ICONS

CAUTION

Please avoid the following situations that could cause damage to

your device:

NOTEINTRODUCTION

Thank you for your choosing the S2 Headphone AMP. Please read this guide

at first to know information about aune S2 Headphone AMP.

S2 Headphone AMP is a high-quality advanced headphone amplifier. With a

high voltage drive technology, S2 is designed to drive headphone with

impedance from 32-600ohm, and provide a perfect listening experience.

For more upgrade information please visit: www.auneaudio.com

UNPACK

Your S2 Headphone AMP has been packed safely in a special designed

container. Please keep the container for emergency usage (in case

send back for repair) .

Check your product box for the following items:

S2 Headphone AMP*1

Power supplier*1

5-pin DC power cable*1

AC power cord*1

User’s guide*1

Warranty card*1

HIGHLIGHTS

Separated main body and power supplier design, provide a lower power

supply interference

Light touch switchers, switch signal source easily

Ecellence integrate circuit design for superior audio parameter and

sound quality

S2 Headphone AMP has time-delay and protection circuit, the LED on

front panel will blink a few seconds and S2 will get ready to work after

power connected.

S2 can be set mute just long press input selection switch till LED

extinguished. To cancel the mute, long presses the input selection switch

again, till the LED lightens.When out of service for long term, turn the

volume to minimum, and unplug the headphone.

Plug-in headphone only when S2 was turn on and the volume was set

minimum.

Please use the S2 headphone as the following instructions:

5

4

Input source selection switch

Input source selection LED

1/4＂ stereo jack for headphone

Volume controller

RCA jacks for audio signal input

POWER IN--5-pin DC power cable jack

DEVICE LAYOUT

FRONT PANEL

REAR PANEL

DEVICE LAYOUT

Headphone AMP

Connect the supplied AC power cord to the power supply module, then

connect main body and Power supplier with supplied 5-pin DC power

cable

Audio signal output of device such as CD player IPOD and audio DAC

can connect to LINE 1 or LINE 2 RCA jacks on the rear panel of

S2

Touch the input source selection switch on front panel to select right input

source. When input signal was connected to LINE 1 the LED

indicated LINE 1 should lighten

Rotate the volume controller to adjust output volume

，，

" " " "

" "，

" "

Used as a headphone amp:

Use with other device

We recommend you to use S2 HEADPHONE AMP with high quality audio

signal output device and headphone, for instance, use with aune S1 music

player and Sennheiser HD650 will be a good choice

6

AUNE S2 User manual

AUNE S2 User manual

Related papers

Other documents