Sony XS-GTF1025B Operating instructions

XS-GTF1025B
Sony
Brand
Sony
Model
XS-GTF1025B
Category
Car speakers
Type
Operating instructions

Sony XS-GTF1025B is a powerful and versatile 10 cm coaxial 2-way speaker system that delivers high-quality audio in various mounting scenarios. With a peak power handling capacity of 130W and a rated power of 30W, it can produce loud, clear sound without distortion. The speaker's frequency response ranges from 45 Hz to 25,000 Hz, ensuring accurate reproduction of both low and high frequencies. Its impedance of 4 ohms allows for easy integration with various audio systems. The package includes parts for installation, making it a convenient choice for car audio enthusiasts.

Sony XS-GTF1025B is a powerful and versatile 10 cm coaxial 2-way speaker system that delivers high-quality audio in various mounting scenarios. With a peak power handling capacity of 130W and a rated power of 30W, it can produce loud, clear sound without distortion. The speaker's frequency response ranges from 45 Hz to 25,000 Hz, ensuring accurate reproduction of both low and high frequencies. Its impedance of 4 ohms allows for easy integration with various audio systems. The package includes parts for installation, making it a convenient choice for car audio enthusiasts.

Precautions
•Do not continuously use the speaker
system beyond the peak power handling
capacity.
• Keep recorded tapes, watches, and
personal credit cards using magnetic
coding away from the speaker system to
protect them from damage caused by the
magnets in the speakers.
If you cannot find an appropriate mounting
location, consult your car dealer or your
nearest Sony dealer before mounting.
Installation/Connections
2007 Sony Corporation Printed in China
XS-GTF1025B
3-213-895-21 (1)
Unit: mm
Dimensions
10cm Coaxial
2-way Speaker
24.5
ø 117
5
ø 91.5
ø 65
6 × 9
ø 102.5
43
Specifications
Speaker Coaxial 2-way:
Woofer 10 cm, HOP, cone
type
Tweeter 2.5 cm,
B.D. type
Peak power 130 W*
1
Rated power 30 W*
1
Impedance 4 Ω*
1
Sensitivity 88
±
2 dB (1 W, 1 m)*
2
Frequency response 45 Hz – 25,000 Hz*
1
Mass Approx. 400 g per speaker
Supplied accessory Parts for installation
Design and specifications are subject to change
without notice.
*
1
Testing Condition : IEC60268-5 (2003-05)
*
2
Testing Condition : EIAJ RC-8124A
× aa a a a
× aa a a a
a
×
a
×
ø 142
•
•
*
*
Ω*
±
*
*
*
1
*
2
Parts list/
Mounting/
Mounting from the car interior/
How to remove the grille net.
Before Mounting
A depth of at least 43 mm is required for flush
mounting. Measure the depth of the area where
you are to mount the speaker, and ensure that
the speaker is not obstructing any other
components of the car. Keep the following in
mind when choosing a mounting location:
•Make sure that nothing is obstructing around
the mounting location of the door (front or
rear) where you are to mount the speaker.
•A hole for mounting may already be cut out of
the inner panel of the door (front or rear). In
this case, you need to modify the board only.
•If you are to mount this speaker system in the
door (front or rear), make sure that the speaker
terminals, frame or magnet do not interfere
with any inner parts, such as the window
mechanism in the door (when you open or
close the window), etc.
Also make sure that the speaker grille does not
touch any inner fittings, such as the window
cranks, door handles, arm rests, door pockets,
lamps or seats etc.
•
•
•
Flat mounting (installed flush with the surface of the dash)/
This speaker can be made to fit in almost any type of car by removing
the mounting tabs.
Use clippers or pliers, etc. to cut or snap the mounting tabs off so
that it is even with the edge of the speaker frame as illustrated.
Note
After removing the mounting tabs, handle the speaker frame with
care, as the edges may be sharp.
ø 91 mm
× 2
2
5
× 2
× 8
3
ø 4 × 30
× 8
4
1
6
× 2
Press and insert the edges of the grille net.
5
6
5
65
3
2
*
Striped cord
* White cord — Left speaker
Grey cord — Right speaker
* —
—
To speaker cord of a car.
4
4
3
5
2
8 mm
13 mm
2
Remove the grille net.
6
5
1
Mark the 4 bolt holes and make them 3.3 mm* in diameter.
*
* When using 4 : ø 5 mm
* 4 ø
c
1
Door panel
ø 3.3 mm*
ø 92 mm
  • Page 1 1
  • Page 2 2

Sony XS-GTF1025B Operating instructions

XS-GTF1025B
Sony
Brand
Sony
Model
XS-GTF1025B
Category
Car speakers
Type
Operating instructions

Sony XS-GTF1025B is a powerful and versatile 10 cm coaxial 2-way speaker system that delivers high-quality audio in various mounting scenarios. With a peak power handling capacity of 130W and a rated power of 30W, it can produce loud, clear sound without distortion. The speaker's frequency response ranges from 45 Hz to 25,000 Hz, ensuring accurate reproduction of both low and high frequencies. Its impedance of 4 ohms allows for easy integration with various audio systems. The package includes parts for installation, making it a convenient choice for car audio enthusiasts.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents