WAGO 4-channel, 0 - 20 mA User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Fr ontseite 2015 - mit DocVariab len (Standard) @ 9\mod_1285 229289866_0.doc x @ 64941 @ @ 1

WAGO-I/O-SYSTEM 750

Manual

753-553

4AO 0-

20mA

4-Channel Analog Output Module 0-

20 mA

Version 1.1.0

Pos: 3 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Impressum für Standar dhandbücher - allg. Angaben, Anschrif ten, Telefonnummern und E-Mai l-Adress en @ 3\mod_1219151118203_21. docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Liste für Textmarke Einband_vorne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhalts verzeichnis - Überschri ft oG und Verzeichnis @ 3\mod_1219 151230875_21.doc x @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 15

3.2 Connectors ............................................................................................... 16

3.2.1 Data Contacts/Internal Bus ................................................................. 16

3.2.2 Power Jumper Contacts/Field Supply ................................................ 17

3.2.3 CAGE CLAMP

®

Connectors ............................................................. 19

3.3 Display Elements .................................................................................... 20

3.4 Operating Elements ................................................................................. 20

3.5 Schematic Diagram ................................................................................. 21

3.6 Technical Data ........................................................................................ 22

3.6.1 Device Data ........................................................................................ 22

3.6.2 Power Supply...................................................................................... 22

3.6.3 Communication .................................................................................. 22

3.6.4 Outputs ............................................................................................... 22

3.6.5 Connection .......................................................................................... 23

3.6.6 Climatic Environmental Conditions ................................................... 23

3.7 Approvals ................................................................................................ 24

3.8 Standards and Guidelines ........................................................................ 26

4 Process Image ............................................................................................. 27

5 Mounting ..................................................................................................... 28

5.1 Mounting Sequence ................................................................................. 28

5.2 Inserting and Removing Devices ............................................................ 29

5.2.1 Inserting the I/O Module .................................................................... 29

5.2.2 Removing the I/O Module .................................................................. 30

5.3 I/O Modules with Pluggable Wiring Level (Series 753) ........................ 31

5.3.1 Coding ................................................................................................ 32

5.3.2 Connector Removal ............................................................................ 34

6 Connect Devices ......................................................................................... 35

6.1 Connecting a Conductor to the CAGE CLAMP

®

................................... 35

6.2 Connection Example ............................................................................... 37

4 Table of Contents WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

7 Use in Hazardous Environments .............................................................. 38

7.1 Marking Configuration Examples ........................................................... 39

7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 39

7.1.2 Marking for America According to NEC 500 .................................... 44

7.2 Installation Regulations ........................................................................... 45

7.2.1 Special Conditions for Safe Use (ATEX Certificate

TÜV 07 ATEX 554086 X) ................................................................. 46

7.2.2 Special Conditions for Safe Use (ATEX Certificate

TÜV 12 ATEX 106032 X) ................................................................. 47

7.2.3 Special Conditions for Safe Use (IEC-Ex Certificate

TUN 09.0001 X) ................................................................................. 48

7.2.4 Special Conditions for Safe Use (IEC-Ex Certificate

IECEx TUN 12.0039 X) ..................................................................... 49

7.2.5 Special Conditions for Safe Use According to

ANSI/ISA 12.12.01 ............................................................................ 50

List of Figures ...................................................................................................... 51

List of Tables ........................................................................................................ 52

=== Ende der Liste für Textmarke Verzeichnis_ vorne ===

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften für alle Seri en/Hinweise zur Dokume ntation/Hinweise zu di eser Dokumentati on - Über schr ift 1 @ 4\mod_1237987661750_21. docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Hinweise/Hinwei s: Dokumentation aufbe wahren @ 4\mod_1237987 339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /Alle Serien (Al lgemeine Module)/Über schriften für alle Seri en/Hinweise zur Dokume ntation/Gültigkei tsbereich - Übersc hrift 2 @ 12\mod_1338912448776_ 21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /Serie 750 ( WAGO-I/O-SYSTEM)/Hin weise zur Dokumentati on/Gültigkeitsber eich/Gültigkeit sbereich Dokumentati on Busklemme 750-xxxx, ohn e Variantenangabe @ 14\ mod_1358944037947_2 1.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 753-553

(4AO 0-20mA).

Pos: 11 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumenta tion/Hinweise/Acht ung: Hinweis zur Dokume ntation Busklemmen 750- xxxx @ 4\mod_1237986979 656_21.docx @ 29023 @ @ 1

The I/O module 753-553 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /Alle Serien ( Allgemeine Module)/ Hinweise zur Dokumentati on/Urheberschut z ausführlich @ 4\mod_123 5565145234_21.doc x @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 12.3 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Serien/Hinweise zur Dok umentation/Symbo le - Überschrift 2 @ 13\ mod_1351068042408_21.doc x @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12.4.1 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden a llgemein_ - Erläuterung @ 13\ mod_1343309450020_ 21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.2 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden dur ch elektrischen Stro m_ - Erläuterung @ 13\mod_134 3309694914_21.doc x @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.3 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweis e/Warnung/War nung: _Warnung vor Personenschäd en allgemein_ - Erläut erung @ 13\mod_134330987704 1_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12.4.4 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweis e/Vorsicht/Vorsi cht: _Warnung vor Personen schäden allgemein _ - Erläuterung @ 13\mod_1343310 028762_21.doc x @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12.4.5 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden al lgemein_ - Erläuteru ng @ 13\mod_1343310134623_21. docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.6 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden dur ch elektrostatische A ufladung_ - Erläuter ung @ 13\mod_13433102277 02_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.7 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: _W ichtiger Hinweis al lgemein_ - Erläuterung @ 13\ mod_1343310326906_21. docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12.4.8 /Alle Serien ( Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Information/I nformation: _Wei tere Information allgemein _ - Erläuterung @ 13\mod_1343310 439814_21.doc x @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

753-553 4AO 0-20mA

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.doc x @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 12.6 /Alle Serien ( Allgemeine Module)/ Hinweise zur Dokumentati on/Darstellung der Zahlensysteme - Übersc hrift 2 und Inhalt @ 3\mod_122 1059454015_21.doc x @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12.7 /Alle Serien ( Allgemeine Module)/ Hinweise zur Dokumentati on/Schrif tkonventionen - Übersc hrift 2 und Inhalt @ 3\mod_1221 059521437_21.doc x @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 14 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Wichtige Erläu terungen/Wichti ge Erläuterungen - Übersc hrift 1 @ 4\mod_1241428899156_ 21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /Alle Serien ( Allgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Wichtige Er läuterungen - Einleitun g @ 3\mod_1221059818031_21. docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Serien/Wichtige Er läuterungenRechtlic he Grundlagen - Übersc hrift 2 @ 3\mod_12210606263 43_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /Alle Serien ( Allgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Änderungsvorb ehalt - Überschrif t 3 und Inhalt @ 3\mod_12210600364 84_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Personalqua lifikationPerson alqualifikation 750- xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240612080 46_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterungen/ Bestimmungsgemäße Ver wendungBestimmu ngsgemäße Verwendung 750- xxxx - Überschrif t 3 und Inhalt @ 3\mod_12240641512 34_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /Alle Serien ( Allgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuter ungen/Technischer Zustand der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_12210 60446109_21.docx @ 217 23 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 15.8 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Serien/Wichtige Er läuterungenSicher heitshinweise - Überschr ift 2 @ 6\mod_1260180299987 _21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /Alle Serien ( Allgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheitshi nweise/Einleitung Si cherheitshin weise Hardware @ 6\mod_1260 180170493_21.doc x @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.10.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Gefahr /Gefahr: Nicht an Gerä ten unter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Gefahr/Gefahr: Einbau 0750-xxxx nur i n Gehäusen, Schränken oder ele ktrischen Betriebsr äumen! @ 6\mod_1260180556 692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.10.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Gefahr /Gefahr: Unfall verhütungsvorschr iften beachten! @ 6\mod_1260 180657000_21.doc x @ 46735 @ @ 1

Pos: 15.10.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Gefahr /Gefahr: Auf normgerec hten Anschluss achten! @ 6\mod_1260180753479_ 21.docx @ 46739 @ @ 1

Pos: 15.11.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Defekte od er beschädigte Geräte au stauschen! @ 6\mod_126018 0857358_21.doc x @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.11.2 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Geräte vor kriechenden und isolier enden Stoffen schütze n! @ 6\mod_126018103621 6_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.11.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Reini gung nur mit zulässigen Mater ialien! @ 6\mod_12601812 03293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.11.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Kein Kontak tspray verwenden! @ 6\mod_1260181290808_21. docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.11.5 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Verpolun g vermeiden! @ 6\mod_1260184 045744_21.doc x @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.11.6 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Elektrosta tische Entladung ver meiden! @ 6\mod_12601813647 29_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Ser ien/Gerätebeschrei bung/Gerätebesc hreibung - Überschr ift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Anwendung/AO/Anwendu ng 750-05xx AO (0.. .20mA) @ 5\mod_1247047470432 _21.docx @ 36845 @ @ 1

The analog output module 753-553 (4AO 0-20mA) generates a standardized

signal of 0 … 20 mA for the field area.

Pos: 18.1.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ I/O-Beschreibung/ AO/I/O-Beschrei bung 750-05xx 4 AO 2-Leiter ( AO1...AO4 und Masse) @ 5\mod_1247 053300854_21.doc x @ 36880 @ @ 1

The I/O module has 4 output channels, making direct wiring of four 2-wire

actuators possible.

The actuators are connected to CAGE CLAMP

®

connectors AO 1 and common

(ground) or AO 2, AO 3, AO 4 and respective common (ground).

Pos: 18.1.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ I/O-Beschreibung/ AO/I/O-Beschrei bung 750-05xx AO Gemeinsa mes Massepotential @ 5\mod_12 47050255026_21.doc x @ 36870 @ @ 1

The channels have a common ground potential.

Pos: 18.1.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ I/O-Beschreibung/ Allgemein/Verwei s auf Kapitel "Anschlüsse" @ 8\mod_12 76775378035_21.doc x @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.1.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ I/O-Beschreibung/ Allgemein/Verwei s auf Kapitel "Geräte ans chließen" > "Anschlus sbeispiel(e)" @ 5\mod_1246 015203281_21.doc x @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

Pos: 18.1.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei tshinweise/Hin weisHinweis: AI Unzuläs sige Kombination der Bürdenwerte @ 5\mod_1247123924 611_21.docx @ 36962 @ @ 1

ΩΩ

Avoid any unacceptable combination of load impedance values!

The output load impedance values for an I/O module must always be situated

within a range of 0 ... 300 Ω or 300 ... 600 Ω.

The load impedance values are checked by the I/O module; any unacceptable

combination will result in an error message.

Pos: 18.1.7 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ LED-Anzeige/LED Zus tand Betrieb und Klemmen bus-Kommunikation 1 x LED @ 20\mod_1406807126779_21. docx @ 160703 @ @ 1

A green status LED indicates the operating status and error-free I/O module

communication.

Pos: 18.1.8 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ LED-Anzeige/LED Feh ler Drahtbruch/unzu lässige Bürdenkombina tion @ 5\mod_124705517516 6_21.docx @ 36896 @ @ 1

A red error LED indicates a wire break or an unacceptable combination of load

impedance values.

Pos: 18.1.9 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ LED-Anzeige/Ver weis auf Kapitel "Anzeig eelemente" @ 5\mod_124601 0525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.1.10 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Versorgung/Span nungsversorgung au s Feldversorgungspa nnung @ 5\mod_124711687735 3_21.docx @ 36927 @ @ 1

The voltage supply is done via the field supply.

Pos: 18.1.11 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Versorgung/Versor gung 24 V, 0 V über Leistungsko ntakte Standard @ 3\mod_1226 498974531_21.doc x @ 25020 @ @ 1

The I/O module 753-553 (4AO 0-20mA) receives the 24 V voltage supply for the

field level from an upstream I/O module or from the fieldbus coupler/controller

via blade-formed power jumper contacts. It then provides these potentials to

subsequent I/O modules via spring-formed power jumper contacts.

Pos: 18.1.12 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Achtung/Achtu ng: Maximaler Strom Lei stungskontakte 10 A @ 3\mod_1 226499143500_21.doc x @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.1.13 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Funktion/Galvani sche Trennung Ausgang ssignal/Systemeb ene (12 Bit) @ 5\mod_124705064 1729_21.docx @ 36877 @ @ 1

The Output signal is electrically isolated and will be transmitted with a resolution

of 12 bits.

Pos: 18.1.14 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Versorgung/Anordnu ng unter Berücksic htigung der Leistungskon takte beliebig @ 3\mod_123 3756233468_21.doc x @ 27099 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 18.1.15 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/ Einleitung/Einsa tzbereich/Ei nsatzbereich 750-xxxx a lle Koppler/Control ler ohne Economy-Koppler @ 3\mod_1232541867468_21.d ocx @ 26525 @ @ 1

The I/O module 753-553 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -323, -324

and -327).

Pos: 18.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 18.3 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Serien/Gerätebeschr eibung/Ansicht - Überschrift 2 @ 4\mod_12409 84217343_21.doc x @ 31958 @ 2 @ 1

3.1 View

Pos: 18.4 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Ansicht/Anal ogausgangsklemmen/A nsicht 753-0553 @ 24\mod_14449 26845132_21.doc x @ 193662 @ @ 1

Figure 1: View

Pos: 18.5 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Ansicht/Ansi cht – Legende mit Leistung skontakten_mit Kodier ung, Kabelbefestig ung und Prüföffnungen @ 20\ mod_1411031302199_21. docx @ 163871 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with Mini-

WSB

---

2

Status-LEDs

“Device Description” > “Display

Elements”

3

Data contacts

“Device Description” > “Connectors”

4

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

5

Release tab

“Mounting” > “Inserting and Removing

Devices” and “I/O Modules with

Pluggable Wiring Level (Series 753)”

6

Coding possibility with coding

fingers

“Mounting” > “Coding”

7

Power jumper contacts

“Device Description” > “Connectors”

8

Test port

---

9

Fixing lug for cable ties

“Mounting” > “I/O Modules with

Pluggable Wiring Level (Series 753)”

Pos: 18.6 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 18.7 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Serien/Gerätebeschr eibung/Anschlüsse - Überschrift 2 @ 4\ mod_1240984262656_21.doc x @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 18.8 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Dat enkontakte/Kle mmenbus - Überschri ft 3 @ 6\mod_1256294684083_21. docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 18.9.1 /Ser ie 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüs se/Datenkontakte - Feldbuskoppler/- controller, Abbildun g und Beschreibung @ 3\mod_123 1771259187_21.doc x @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 18.9.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Achtung/Achtun g: Busklemmen nicht auf Goldfederkontakte legen! @ 7\mod_1266318463636_ 21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 18.9.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Achtung/Achtun g: ESD - Auf gute Erdung der Umgebun g achten! @ 7\mod_1266318538 667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 18.10 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 18.11 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte/ Feldversorgun g - Überschrift 3 @ 6\mod_1256 294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 18.12.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Vorsicht/Vorsi cht: Verletzungsg efahr durch sc harfkantige Messerkontakte! @ 6\mod_1256193279401_21. docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 18.12.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüsse/ Leistungskontak te 2 LK (Messer/Leistungsko ntakte 2 LK (Messer/F eder) - Einleitung @ 15\ mod_1371721641099_21. docx @ 123714 @ @ 1

The I/O module 753-553 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 18.12.3 /Seri e 753 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüsse/ Leistungskontak te 2 LK (Messer/Leistungsko ntakte/Feldver sorgung 2 LK (Messer/Feder) - Abbildung @ 17\mod_1381924 880242_21.doc x @ 134239 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 18.12.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüsse/Lei stungskontakte 2 LK ( Messer/Leistungsko ntakte 2 LK (Messer/Feder ) - Legende @ 15\mod_13717 21352500_21.docx @ 123710 @ @ 1

Table 4: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

1

Spring contact

Potential transmission (U

v

) for field supply

2

Spring contact

Potential transmission (0 V) for field supply

3

Blade contact

Potential feed-in (0 V) for field supply

4

Blade contact

Potential feed-in (U

v

) for field supply

Pos: 18.12.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Achtung/Achtu ng: Maximaler Strom Lei stungskontakte 10 A @ 3\mod_1 226499143500_21.doc x @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.12.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Hinweis/Hinweis: Potentialeins peiseklemme für Erde ei nsetzen! (keine LK für Erde) @ 3\mod_1226499037468_21. docx @ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 18.13 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 18.14 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/CA GE CLAMP-Anschlüsse - Üb erschrift 3 @ 6\ mod_1256296337770_21.doc x @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

®

Connectors

Pos: 18.15 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Ana logausgangsklem men/Anschlüsse 753-0553, -0555 4 AO 2-Leiter @ 24\mod_14449 27138831_21.doc x @ 193670 @ @ 1

Figure 4: CAGE CLAMP

®

Connectors

Table 5: Legend for Figure “CAGE CLAMP

®

Connectors”

Channel

Designation

Connector

Function

1

AO 1

1

Output AO 1: Signal voltage

0 V

2

Output AO 1: Actor supply 0 V

2

AO 2

5

Output AO 2: Signal voltage

0 V

6

Output AO 2: Actor supply 0 V

3

AO 3

3

Output AO 3: Signal voltage

0 V

4

Output AO 3: Actor supply 0 V

4

AO 4

7

Output AO 4: Signal voltage

0 V

8

Output AO 4: Actor supply 0 V

Pos: 18.16 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

753-553 4AO 0-20mA

Manual

Version 1.1.0

Pos: 18.17 /Alle Seri en (Allgemeine Module)/ Überschriften für alle Serien/Gerätebe schreibung/Anzeigee lemente - Überschr ift 2 @ 4\mod_1240984390875_21.doc x @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 18.18 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anzeigeelement e/Analogausgang sklemmen/Anzeigeele mente 750-0555 4AO (Agn, Br t) @ 20\mod_1406807365639_2 1.docx @ 160777 @ @ 1

Figure 5: Display Elements

Table 6: Legend for Figure “Display Elements”

Designation

LED

State

Function

Function A

Off

No operational readiness or the internal data bus

communication is interrupted

Green

Operational readiness and trouble free internal

data bus communication

Error B

Off

No error

Red

Overload or short circuit to ground in one of the

output channels

Pos: 18.19 /Alle Seri en (Allgemeine Module)/ Überschriften für alle Serien/Gerätebesc hreibung/Bedienel emente - Überschrif t 2 @ 4\mod_1239191655456_21.doc x @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 18.20 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Bedienelemente/ Bedienelemente Bu sklemme 750-xxxx nicht vor handen @ 4\mod_1236322031 125_21.docx @ 28063 @ @ 1

The I/O module 753-553 has no operating elements.

Pos: 18.21 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

Page is loading ...

WAGO 4-channel, 0 - 20 mA User manual

WAGO 4-channel, 0 - 20 mA User manual

Related papers

Other documents