Overland Storage 2196000 Quick start guide

Brand: Overland Storage

Model: 2196000

Category: Networking

Type: Quick start guide

This manual is also suitable for

Snap Server 600 Series

Overland Storage 2196000 is a rack-mountable server that provides fast, reliable storage for your business-critical data. With its high-performance SAS/SATA disk drives, the 2196000 can handle even the most demanding workloads. And with its built-in RAID controller, the 2196000 can protect your data from disk failures.

The 2196000 is also easy to manage, with a web-based administration tool that makes it simple to configure and monitor the server. And with its hot-swappable disk drives, the 2196000 can be serviced without taking it offline.

Here are some of the benefits of using the Overland Storage 2196000:

Page is loading ...

About This Guide

This guide shows you how to install your Snap Server 500 series or 600 series in a rack and connect the

server to your network. The instructions consist of 5 steps:

Step 1: Verify the contents of your shipping package.•

Step 2: Install the server in the rack.•

Step 3: Connect power and network cables.•

Step 4: Power on the Snap Server.•

Step 5: Connect to the Snap Server for the ﬁrst time.•

Step 1: Verify the Contents of the Shipping Package

Before you begin installation, check to make sure you have all the hardware components required for your

system.

Check the contents of your Ship Kit to make sure you have all the components described in the •

Hardware

Features

section.

Gather any optional components that you need to complete your system (described below in the •

Optional

Hardware Components

table).

Optional Hardware Components

Component Description

Tape Backup Device(s)

and Cables

To attach a tape device via a SCSI connection to the Snap Server, you need a

68-pin VHDCI cable. For a list of compatible backup solutions, see the Support

section of the Snap Server Web site. To attach a tape device via USB, you need a

USB 2.0 cable.

Power Supply Upgrade The Snap Server 520 and 620 can be upgraded to a second power supply. The

Snap Server 650 comes with dual power supplies.

APC-brand UPS devices Snap Servers are designed to work with a USB- or network-based APC-brand

UPS. Visit the APC Web site for a list of APC models to use with your Snap Server.

SAS HBA Upgrade The Snap Server 520 and 620 can be upgraded to include a SAS HBA to attach

to an expansion array. The Snap Server 650 comes equipped with a SAS HBA.

Dual-Gigabit Ethernet

PCI Adapter

The Snap Server 520, 620, and 650 can be upgraded to 4 Ethernet Ports with

the installation of a dual-gigabit Ethernet Adapter.

Memory Upgrades Memory upgrades are available for the Snap Server 520, 620, and 650. You

can add memory up to 4 GB. However, you cannot install DIMMs of different

capacity on the same server. When adding memory to the Snap Server 650, you

must mirror the upgrade across both DIMM banks (for example, if you add an

additional 1 GB DIMM to one DIMM bank, you must mirror that addition in the

second DIMM bank).

Hardware Features

1 Power button 9 Hot-swappable disk drives (4) 17 Ethernet cables (2)

2 Reset button 10 Power supply modules (2) * 18 Power cables (2 US, 2 UK, 2 EU)*

3 System status lights 11 Primary Ethernet port 19 Inner slide rails (2)

4 Disk drive status lights 12 Secondary Ethernet port 20 Outer slide rails (4)

5 Bezel release mechanisms 13 USB 2.0 ports (2) 21 Rack mount screws

6 Unit ID (UID) light and button 14 Service connector 22 Quick Start Guides and User CDs (3)

7 Not active (for future use) 15 Unit ID (UID) light and button

8 LCD (Liquid Crystal Display) 16 SCSI connector

* The Snap Server 520 and 620 have a single power supply and one power cable (1US, 1UK, 1EU).

Note: USB connectors cannot be used for administrative purposes. Snap Servers are managed via the browser-

based Administration tool.

Quick Start Guide

and User CD

Kurzanleitung und Benutzer-CD

Guía de iniciación

rápida

y CD del usuario

Guide de mise

oute rapide et CD de l’utili

teur

Guida

rapida all’uso e CD utente

Руководство

по быстрой

установке и

компакт�диск

User CD

Quick Start Guide

and User CD

Kurzanleitung

und

Benutze

-CD

Guía

iniciación rápida y

del usuario

Guide

de mise

route rapide et

CD de l’utilisateur

Guida rapida

all’uso e

utente

Руководство

по быстрой установке и

комп

акт�диск User CD

Quick Start Guide

and User CD

Kurzanleitung

und Benutzer-CD

Guía de iniciación rápida y

CD del usuario

Guide

mise

en r

oute rapide et CD de l’utilisa

teur

Guida rapida

all’uso e CD utente

Руководство по быстрой установке и

компакт�диск User CD

Step 2: Install the Server in a Rack

Note The Snap Server 500 Series and 600 Series models can only be mounted in a four-post, 32-inch depth,

EIA-compliant rack. A two-post telco-style rack or a rack less than 32-inches in depth will not support the server.

As shown in the Hardware Features illustration, the Snap Server ships with two slide rail assemblies consisting of

inner rails to attach to the chassis, outer rails to attach to the rack, and a packet of screws for mounting the rails

to the chassis and to the rack. The rails are not universal. They are stamped Left and Right and must be mounted

correctly (stamped designation refers to left and right as you are facing the front of the unit).

You will need a Phillips screwdriver to mount the rails and a second person to help position the Snap Server into

the rack.

Attach the Sliders to the Chassis

1 Take the left inner slider and position it on the left side toward the rear of

the chassis. The tongues on the chassis should ﬁt through the rectangular

holes on the rail, and the release mechanism should be facing out.

2 Slide the rail forward, and continue to slide until you can feel that it’s

attached securely (see illustration).

3 Fasten with the rail attachment Phillips screw.

4 Repeat Steps 1 through 3 for the right inner slider.

Attach the Slide Rail Assemblies to the Rack

1 Assemble the outer slide rail assemblies by ﬁtting the longer rail piece

on top of the shorter rail piece and pulling outward until the two pieces

lock.

2 Position one of the rail assemblies in the rack (making sure you place

the right-stamped rail on the right side of the rack).

3 Align the front holes with the front

holes in the rack and screw a rail screw into the bottom hole. Note that the

rack holes are not evenly spaced. Be sure to align the rail so that the rail

holes match up with the rack holes.

4 Align the rear holes with the rear holes in the rack and screw rail screws in

the top and bottom holes.

5 Repeat Steps 2, 3, and 4 for the second rail.

Mount the Chassis in the Rack

1 Align the inner sliders (attached to the chassis) with the front ends of

the slide rail assemblies (attached to the rack) and slide the server

into the rack.

2 Line up the holes on the inner sliders with the holes on the rack/

outer rails, and secure the chassis with the remaining screws.

Step 3: Connect Power and Network Cables

The server has Dual-Gigabit Ethernet ports that can connect to 10BaseT, 100BaseTx, or 1000BaseT networks. A

dual-port conﬁguration offers added advantages, such as load balancing and failover. You may connect one or

both of the ports.

If you connect only one port, you must use the primary port on the back of the server, as shown in the •

Hardware Features illustration.

To take advantage of network bonding (load balancing or failover), both ports must be physically connected •

to the network; and (a) for load balancing, connected to the same switch on the same subnet; or (b) for

failover, connected to different switches on the same subnet (in case one switch fails).

Caution The speed/duplex setting on Snap Servers defaults to autonegotiate. The networking switch or hub

to which the server is connected must also be conﬁgured to autonegotiate; otherwise, network throughput or

connectivity to the server may be seriously impacted.

Cabling the Server to the Network

Use the provided Ethernet cables to connect the server to the network. When you connect the network cables to

active ports, the network lights on the bezel (LAN 1 and LAN 2) are green.

Connecting the Power Cord

Note The Snap Server 650 (shown)

has dual power supplies. The Snap

Server 520 and 620 (not shown) have

a single power supply and will require

only one UPS and/or electrical outlet for

installation.

As a data integrity measure, Overland Storage strongly recommends you connect each power supply module to a

separate power source via a separate UPS. Use the provided power cords to plug the modules into the UPSs or

properly grounded electrical outlet(s).

Note Snap Servers are designed to work with APC-brand, USB- or network-based UPS devices to automatically

shut down cleanly in the event of a power failure. You must conﬁgure the APC unit both in the Snap Server’s

Administration Tool and in the APC user interface.

Step 4: Power on the Snap Server

To turn on the server, press the power button on the front of the

server. The server takes a few minutes to initialize. The LCD will

display the server’s name and IP address when the system has fully

initialized.

Note If you are connecting an expansion array, use the array’s

documentation to install and connect the array before powering on the Snap Server.

Power

Step 5: Connect to the Snap Server for the First Time

Snap Servers are preset to acquire an IP address from a DHCP server. If no DHCP server is found on the network,

the Snap Server defaults to an IP address of 10.10.10.10, and you may not be able to see the server on your

network. You can discover a Snap Server using either the default server name or the Snap Server Manager (SSM)

utility. Use the server name method if you are installing a Snap Server on a network with a DHCP server. Use SSM

if your network does not have a DHCP server or if your network does not have name resolution services.

To Connect to a Snap Server Using the Server Name

This procedure requires that name resolution services (via WINS or an equivalent service) be operational.

1 Find the server name. The default server name is SNAPnnnnnn, where nnnnnn is the server number.

For example, the name of a Snap Server with a server number of 610019 is SNAP610019. The server number

is a unique, numerics-only string that appears on a label afﬁxed to the top of the server in the left front corner.

2 In a Web browser, enter the following URL:

http://SNAPnnnnnn (where SNAPnnnnnn is the server name)

3 Press Enter. The Web View screen opens.

4 Log into the Administration Tool and complete the Initial Setup Wizard.

Click the administration link. In the login dialog box, enter admin as the user name and admin as the

password, then click OK. Complete the setup procedure using the Initial Setup Wizard.

To Connect to a Snap Server Using Snap Server Manager

Snap Server Manager (SSM) is a Java-based, multiserver administrative application that runs on all major

client platforms. Use SSM to discover, conﬁgure, and monitor all local and remote GuardianOS Snap Servers.

You can download and install SSM using the Install_SnapServerTools.html ﬁle on your Snap Server User CD. Be

sure to install SSM on a computer residing on the same network segment as your Snap Server(s).

1 Launch SSM.

SSM discovers all Snap Servers on its local network segment and displays their server names, IP addresses,

and other status information in the main console. If you do not have a DHCP server, there might be a delay

before the server appears on the network.

Note: To distinguish multiple Snap Servers, you may

need to ﬁnd their default server names as explained

in the previous procedure.

2 If using a DHCP server, proceed to Step 3.

Otherwise, assign an IP address to the server.

In SSM, right-click the server name and select Set

IP Address. Enter an IP address and a subnet mask,

then click OK.

3 Launch a server’s Administration Tool.

In SSM, right-click a server name and select Launch

Web Administration, as shown in the illustration.

4 Log into the Administration Tool and complete the Initial Setup Wizard.

Click the administration link. In the login dialog box, enter admin as the user name and admin as the

password, then click OK. Complete the setup procedure using the Initial Setup Wizard.

70990861-002 Rev B

User CD

Obtaining Service

To obtain service or technical support for your Snap

Server, please visit our Web site at http://www.snapserver.com,

or call 1-888-343-SNAP. For immediate response to a service inquiry, you can

submit a question to our technical support department using our Expert Knowledge Base

System http://www.snapserver.com/kb

Technischen Service

Sie finden den technischen Service oder Kundendienst für Ihren Snap Server auf unserer Website. Wenn Kunden

sofortige Antworten auf eine Serviceanfrage wünschen, können sie mit Hilfe unseres Expert Knowledge Base System

http://www.snapserver.com/kb

Obtención de servicio de asistencia

Para obtener servicio o asistencia técnica para su Snap Server, visite nuestro sitio Web. Para obtener respuesta inmediata a su

solicitud de asistencia, envíelas en la forma de preguntas a nuestro Sistema experto de base de conocimiento en

http://www.

snapserver.com/kb

Obtention d‘un entretien

Pour un entretien ou une assistance technique concernant votre Snap Server, vérifiez notre site web. Pour obtenir une réponse immédiate

à une demande de service, vous pouvez envoyer une question à notre service d‘assistance technique en utilisant notre système de base

de connaissances experte http://www.

snapserver.com/kb

Richiesta di assistenza tecnica

Per informazioni su come richiedere assistenza o supporto tecnici sulle unità Snap Server, visiti il nostro website. Per assistenza

immediata su un problema, è possibile inviare una richiesta al reparto di assistenza tecnica tramite il sistema Expert

Knowledge Base, disponibile all’indirizzo

http://www.snapserver.com/kb

Сервисное обслуживание

Сведения о сервисном обслуживании серверов Snap Server посетите наше веб-узле. Для

быстрого получения ответа на технические вопросы от службы поддержки их можно

размещать в базе знаний Expert Knowledge Base System по адресу

http://www.snapserver.com/kb

www.snapserver.com 888-288-4206

All other product names or company names are the property of their

respective owners.

vorbehalten. Alle anderen Produktnamen und Firmennamen sind Eigentum

der jeweiligen Unternehmen.

en el ámbito internacional. Todos los otros nombres de productos o de

compañías son propiedad de susrespectivos priopietarios.

monde entier. Tous les autres noms de produit ou de société appartiennent

à leurs détenteurs respectifs.

paesi del mondo. Tutti i nomi di prodotti e società sono di proprietà dei

rispettivi proprietari.

Прочие названия изделий и компаний являются собственностью

соответствующих владельцев.

Overland Storage 2196000 Quick start guide

Brand: Overland Storage

Model: 2196000

Category: Networking

Type: Quick start guide

This manual is also suitable for

Snap Server 600 Series

Here are some of the benefits of using the Overland Storage 2196000:

Download PDF

report

Overland Storage 2196000 Quick start guide

This manual is also suitable for

Overland Storage 2196000 Quick start guide

Related papers

Other documents