Snooper syrius s600 plus User manual

Brand: Snooper

Model: syrius s600 plus

Category: Car navigation systems

Type: User manual

Developed by

Mapping by

Introduction

Congratulations on buying the Syrius Plus Portable Navigator and Fixed Speed Camera location system.

This user manual aims to provide you with installation and operating instructions for the Syrius Plus.

The Syrius Plus utilises the very latest Global Positioning Satellite (GPS) technology to provide you with accurate street level

navigation via clear and precise voice prompts as well as alerting you to potentially hazardous stretches of road, accident

black spots and xed speed safety cameras.

The most accurate digital mapping available is provided by

whilst the geographical coordinates of all ‘xed’

speed monitoring systems and many ofcially designated accident ‘hotspots’ have been stored on a database provided by

Enigma™. The Enigma™ Database is the most comprehensive available, providing cover, not only in the UK and Ireland,

but throughout Western Europe as well. The database is constantly monitored and updated by the Enigma™ data collection

team, ensuring that you are alerted to every potentially hazardous stretch of road and all xed speed safety cameras.

The Syrius Plus comes with an SD Card that contains the UK & Ireland navigation software. The SD Card can be activated

in seconds by inserting the card into the SD slot on the top of the unit. When necessary, upgrades to this mapping data will

be made available for you once every twelve months.

As the Enigma™ camera database changes daily, regular updates to your Syrius Plus are required. The Syrius Plus

connects quickly and easily to your PC so that you can download the database in a matter of minutes (internet connection

required). Please note: In order for the software to be installed successfully, there are certain minimum hardware and

software requirements needed; see the section ‘System Requirements & Downloading’ later in this manual.

Once the database has been downloaded your Syrius Plus compares your position using its built-in GPS antenna, with the

position of every known ‘xed’ speed monitoring system and accident ‘hotspot’ alerting you both audibly and visually with

voice alerts and full colour graphics on the units LCD screen ensuring your highest concentration at all times.

Please note that Enigma™ updates are subject to a subscription charge. Please refer to the subscription and download

section of this manual for further details or visit www.snooperneo.co.uk.

Drive Safely with Snooper!

The Syrius Plus’s camera location technology has been designed and manufactured to help enhance road safety and is in

no way a licence to speed nor has it been designed as a substitute for concentration. Driving within the speed limit, whilst

carefully observing current road conditions is essential.

Contents

Page

4 Components

5 Features

6 Registering your Syrius Plus

7 Quick Start Guide to Navigation

9 Start Up – Installing the SD Card

System Requirements and Downloading

10 Downloading the Enigma™ Camera Database

11 Installing your Syrius Plus

12 Power Connection & Charging

14 Operating Instructions

Starting Up

Easy Set Up

Screen Settings

15 Brightness

16 Volume

Planning a Route

By Full Postcode

17 Find by City

18 Home

19 Ofce

Recent Route or Clear Route

20 Multi-route

22 Find by Favourites

23 Recent Destinations

Find by Points of Interest (POI)

24 Find by Nearest POI

26 Find by Map

27 Re-Route

Avoid by Road Name

28 Avoid by Range

Clear Avoided Road

29 Route Description

My Favourite Menu

Favourites

31 Recent Destination

User Points

33 Home

34 Ofce

35 CongureMenu

36 Brightness

Day - Night

Volume

37 Change Language

Setup

38 2D/3D/North

Speed/Time

MPH/KMH

Arrival Time/Remaining Time

Page

38 Show POI

39 Auto Scale

Camera Alert

40 Display Cameras

Alert Sound

Mute

Auto Mute

41 School

Alert

42 Touch Tone

Route Alert

GPS Status

43 Change Map Colour

Qwerty Keyboard

44 Bluetooth

45 Version (Hardware & Software)

Route Option

Shortest Time

Shortest Distance

46 Avoid Tollway

Avoid Motorway

Navigate Avoiding Road

Avoid by Road Name

47 Avoid by Range

Clear Avoided Road

48 Navigate via Location

Change Start Position

Summary Screen

49 Quick Access Menu

Volume

50 Scroll Map

Day or Night Settings

Camera Alerts

Magnify or Reduce Function

51 Understanding the Mapping Screen

52 Speed Camera Alert Patterns

Fixed Safety Cameras

Risk Zones

SPECs Safety Camera Systems

Saving User Points

53 Troubleshooting - Saving User Points

Deleting Stored User Points

Fixed Camera Pre-Alert Settings

54 Troubleshooting Syrius Downloads

57 Specication

59 Accessories

Service Under Warranty

Return to contents

Components Included

The following components come as standard with your Syrius Plus:-

1 x Syrius Plus Navigation system

1 x SD Card with UK & Ireland mapping

1 x Windscreen suction cup bracket

1 x 12v DC to 5v DC Coiled power lead with cigarette lighter socket adaptor

1 x USB Data Cable

1 x 240V AC to 5V DC mains power adaptor

1 x Download Software Disc (also includes electronic versions of the User Manual and Printable Registration Forms)

PLEASE NOTE

Due to our desire to continually improve our products, the specication may change without notice.

Return to contents

Features

LCD Screen

Power LED

Battery Status LED

On/Off Button

Manual Store

Microphone

(for use with

Bluetooth function)

USB Cable Socket Audio Out Socket Mic In Socket (for use with

Bluetooth function)

Battery ON/OFF switch

Battery Charger

Socket

SD Card Slot

Return to contents

Registering your Syrius Plus

IMPORTANT!

PLEASE READ BEFORE USING YOUR SYRIUS PLUS.

To enable your Syrius Plus to locate Fixed Speed Cameras and Accident Black spots you will have to register and download

the Enigma™ Camera Database.

There are four ways to register your unit:

Go to the ofcial website www.snooperneo.co.uk and register your unit online. Your unit should normally be activated within

30 minutes of registration.

By Telephone

You can contact us by telephone on 0870 787 0700 and select Option 1 between the hours of 9:00am and 5.30pm Monday

to Friday. Your unit should normally be activated within one hour of registration.

By Fax

Print and complete the registration form, which can be located on the CD ROM and fax it to 0870 787 1700 between the

hours of 9:00am and 5:30pm Monday to Friday. Your unit should normally be activated within one hour.

By Post

If you would like to register by post, send the completed registration form to us at the following address.

Performance Products Limited,

Cleaver House, Sarus Court,

Manor Park, Cheshire WA7 1UL.

If you register by post, your unit should normally be activated within 24 hours upon our receipt of your completed registration

form.

Please Note: To register your Syrius Plus you will need the serial number of your unit and you are required to

select from one of two payment options:

One-Off Lifetime Subscription

One up-front payment of £99.95 and receive camera updates via download for the life of the unit. This subscription payment

is none transferable and is available to the original owner only.

Pay Monthly by Direct Debit

Six months FREE, and then pay only £4.95 a month! Payment details (Bank Sort Code and Account Number) must be

provided at the time of registration. Minimum subscription period is for twelve months.

PLEASE NOTE

Due to our desire to continually improve our products, the specication may change without notice.

Return to contents

Quick Start Guide to Navigation

1. Take your Syrius Plus outside so that the GPS receiver

can locate your position. This may take between 15 - 50

minutes the rst time. When satellite lock is achieved,

the screen will display your current position on its map

in a ‘3D’ navigation view. Your position (and direction) is

indicated by the icon.

Tip: To reduce the ‘cold start’ GPS time remain

stationary

2. Bring up the main navigation menu by touching the

centre of the display.

Select

Tip: The icon always means that there are more

options to see on the next screen

3. You will see a standard browser screen, used for

entering postcodes. Enter the full UK postcode using the

keyboard and press

IMPORTANT: Use the key to

separate the two segments of the postcode.

Tip: For a more accurate navigation, you

can enter a House number by pressing the

key.

Return to contents

Tip: The default route options are set to Quickest

Route. To change the route options refer to section

6 in this user manual.

4. Press

and the Syrius Plus will

calculate the fastest route from your current position to

your destination.

This should only take a few seconds and a progress bar

is shown on the screen.

5. A journey summary screen will then be

displayed

Please note: The summary screen is

only displayed for approximately 10

seconds before the unit automatically

begins to provide you with turn-by-turn

instructions.

6. Press

The navigation view will now be displayed, but with

the route now highlighted for you. As you approach a

specic turn in the calculated route, the Syrius Plus will

advise you what to do. For example, “After 200 yards,

turn left”, followed by “Now turn left”. As you proceed

along your journey, following the voice instructions, you

will notice that the navigation view is updated constantly,

always showing approaching roads and junctions and

presenting the best route to you.

Tip: If you miss a turn or drive down a wrong road,

a new fastest route will be calculated automatically,

based on your new position and direction of travel,

a tone will be heard to conrm re-routing. The

Syrius Plus will always give you clear instructions

that will take you to your chosen destination.

Final Destination Estimated arrival Time

Your current

location

Distance to

destination

Estimated

journey time

Return to contents

Start Up – Installing the SD Card

Before using your Syrius Plus, you will need to install the SD Card included

with the device. The SD Card comes complete with a digital map of the UK

and Ireland or Western Europe depending on the model purchased and is also

where the Enigma™ camera database is stored if you choose to subscribe and

download it.

Start by moving the ‘Batt. ON/OFF’ switch located on the underside of the unit

to the ‘ON’ position, then remove the SD card from its packaging and insert it

into the SD Card slot as indicated. Finally switch on the device by pressing and

holding the standby power button located on the left hand side of the unit for 2

seconds. As soon as the device is switched on, the Syrius Plus will automatically

synchronise with the SD Card. Once the synchronisation is completed, the SD

Card will not function with any other device. Your Syrius Plus is now ready to

navigate and the camera database can be downloaded if necessary.

Please note that if the unit does not activate when you press and hold the standby power button for 2 seconds it

may require charging. Refer to the section ‘Charging the internal battery’ later in this manual.

System Requirements and Downloading

Before you can begin to download the database onto your Syrius Plus, you will need to install the Syrius Updater software

provided on the CD ROM.

In order for the software to be installed successfully, there are certain minimum hardware and software requirements

needed.

Hardware Requirements

The computer must have an Intel Pentium Class processor or equivalent, a minimum of 32MB of RAM, a monitor with 256

(8-bit) colours or greater, a CD ROM drive, 20MB of free disc space and a spare USB connection.

Software Requirements

The software will only operate on the following Windows based operating systems:

Windows 2000

Windows XP

Windows Vista

and, in addition, will only work with Internet Explorer 6 or Netscape Navigator 6 or above.

NOTE: The Syrius Plus Updater software does not support Windows 95, 98, Millennium or Apple Macintosh

operating systems.

Software Installation Instructions

Place the Software CD into a CD ROM or DVD drive. Your PC should automatically open a window displaying the

instructions for installing the software. Follow the instructions onscreen to install the download software.

To launch the CD manually: Click on ‘Start’ and then ‘Run’. In the dialogue box that opens click on ‘Browse’ – another

dialogue box will open. Locate your CD ROM or DVD drive (drive letter is normally D) using the ‘Look in’ option and select

‘Menu’ from the lower portion of the dialogue box. Once you have selected ‘Menu’ click on ‘Open’ on the explorer box and

then ‘OK’ on the Run dialogue box.

Please make sure that the operating system installs the new hardware (Win 2K, XP and Vista) before installing the Syrius

Plus Updater software. Once the ‘Syrius Plus Updater’ software has been installed click ‘Finish’ and then close the CD auto

run window. After installing the software, please re-boot your PC.

Any later download software updates can be obtained from www.snooperneo.co.uk. If you have any problems using this

software please call 0870 787 0700 during ofce hours and select Option 3.

Once the software is installed, you are ready to download the database onto your Syrius Plus. The Syrius Plus

download software runs automatically in the background*. This is indicated by the symbol

, which can be

located in the system tray in the bottom right hand corner of your desktop near the system clock.

*When the Syrius Plus Updater is run for the rst time you will be asked to select your language and then to select the camera

data that you wish to download. Select the data you would like and then click ‘OK’. The software is now ready for use.

Return to contents

Downloading the Enigma™ Camera Database

Please Note: You must register your Syrius Plus before you can perform a download.

Performing a download is simple.

1. Connect the AC Power adapter provided to a mains plug socket

and attach the other end to the Syrius Plus in the socket marked

DC 5V.

2. Power up the Syrius Plus by pressing and holding the power

button for 2 seconds and then connect the computer to the

Internet.

3*. Right click on the symbol located in the bottom right hand corner

of your desktop in the system tray and left click ‘Download

Settings’.

4*. Select the les you wish to download (UK Cameras is selected

by default). Once you have selected the les you wish to

download left click the ‘OK’ button.

5. Connect the USB lead to your computer and plug the other end

of the lead into the Syrius Plus in the socket marked USB on the

underside of the unit.

6. The Syrius Plus software will then start to run automatically and

download the database les that you have selected onto your

unit. The download process is as follows:

l The software will display the serial number of your Syrius Plus

and a green progress bar will start to progress across the

screen.

l The software will then connect to our database server and

then download** the database.

l The Syrius Plus will then save the data received.

l The software will indicate that the download is complete and

will instruct you to disconnect the Syrius Plus from your PC.

Note: The software will shut down automatically after 5

seconds if you do not disconnect your unit as instructed.

*You only need to do these steps if you wish to change the data that is downloaded onto the Syrius Plus. If you want the

download settings to be the same as the previous download ignore these two steps.

**If you have a Firewall on your computer, the Firewall software may inform you that the Syrius Plus Updater software is

trying to access the internet. Please make sure that you grant/allow/permit access to the Syrius Plus Updater program

through the Firewall.

Please read the messages supplied by your Firewall software carefully before choosing your option. If you do not allow

the program to access the internet through the Firewall, the download process will fail. Please note: Windows XP SP2 and

Windows Vista come with a built-in rewall as standard.

Plug the charger into a

240V AC mains socket

Connect the USB lead

to your Syrius Plus

Plug the charger cable

into the socket on the

back of the Syrius Plus

Return to contents

Installing your Syrius

The Syrius Plus comes with a windscreen bracket so that the unit can be mounted onto your vehicles windscreen.

When installing your Syrius Plus please ensure that:

l The unit, with its built in GPS antenna has a clear view of the sky*

l It is located in a position where you can easily view the LCD display without having to take your eyes too far from the road

ahead and that you can reach the controls safely.

l Does not interfere with the vehicles controls

l Does not jeopardise the drivers or passengers safety

l You will be able to remove the device to perform downloads.

*Please Note: Some vehicles including Renault, Citroen and Peugeot may come with a ‘Heat Reective’, ‘Metal Oxide’,

‘Athermic’ or ‘Comfort’ windscreen which may affect the performance of the built in GPS antenna. If you are unsure what

type of windscreen is tted to your vehicle then contact your local vehicle dealer or manufacturer for further information. In

these situations you will need to purchase an extension GPS antenna, which can be positioned either on the rear parcel

shelf or outside the cabin of the vehicle. Call 0870 787 0700 and select Option 2 for further details.

PLEASE NOTE: Be careful to choose a location that does not block the drivers view or where it might endanger

the driver or passengers should your vehicle suddenly come to a stop or be involved in an accident.

Installing your Syrius using the Windscreen Suction Cup bracket

You can mount your Syrius Plus to the inside of your vehicles

windscreen using the windscreen bracket provided.

l Clean the area where you wish to position the bracket thoroughly with

a good quality glass cleaner. This allows a more secure seal on the

windscreen.

l Place the suction cup and bracket on the windscreen and push the

locking lever towards the windscreen to secure the bracket.

l Adjust the angle of the bracket so that when the unit is attached to it

you can view the display and operate the controls safely.

l Position the Syrius Plus onto the bracket, by sliding it onto it as

indicated. Remove the Syrius Plus by sliding the unit upwards and off

the bracket.

l The Syrius Plus can be powered directly either from the internal

battery if it is fully charged or powered from the cigarette lighter

socket. To use the cigarette lighter socket, plug the smaller plug on

one end of the power cable into the socket marked DC 5V on the

back of the Syrius Plus and plug the larger plug into the cigarette

lighter socket of your vehicle.

Please Note: Only use the cigarette lighter power cable provided with the Syrius Plus. The Syrius Plus operates

on 5V not 12V and using any other cigarette lighter power cable will damage your device and void the warranty.

Locking

lever

Bracket

adjusters

Return to contents

Power Connection & Charging

Powering and charging your Syrius Plus from the cigarette lighter socket

The Syrius Plus comes with a power cable designed to plug into your vehicles cigarette lighter socket. This lead will power

the device but will also charge the Syrius Plus’s internal battery.

1. Push the ‘Batt. ON/OFF’ switch on the underside of the unit to the ‘ON’ position

2. Then plug the smaller end of the lead into the DC 5V input socket on the back of the Syrius Plus

3. Plug the other end of the cigarette lighter adaptor into your vehicles cigarette lighter socket.

If the Syrius Plus is powered using the cigarette lighter socket a Red LED will illuminate below a Blue LED on the

left hand side of the unit. When the battery is fully charged, the Red LED will turn Blue.

4. Press and hold the standby power button on the left hand side of the unit for two seconds to activate the device.

Please Note: Do not leave your Syrius plugged into the cigarette lighter socket when you start your vehicle. The

cigarette lighter socket is prone to power surges as the vehicle is started and this may cause damage to your unit.

If the Syrius Plus does not power up please check that the cigarette lighter socket is clean of any debris, remembering not to

insert metal objects into the socket. Check that the cigarette lighter adaptor is inserted all the way into the socket and check

that the fuse in the cigarette lighter adaptor is operational. If your Syrius Plus will still not power up, please check that the

cigarette lighter in your vehicle is functioning correctly.

Replacing the Fuse

If the Syrius stops operating, the fuse in the cigarette lighter plug may have blown – the Green LED on the cigarette lighter

plug will not be illuminated. If it has blown, follow these steps and replace it with a 3 amp, 6 x 30mm fast acting fuse.

Caution: Using a fuse that does not meet these ratings or defeating fuse protection can damage your unit, the

power cable, or the vehicles electrical system.

1. Grasp the ring near the tip of the cigarette lighter plug, and then carefully unscrew the ring by turning it counter clockwise.

Caution: If you must use pliers to loosen the ring, be careful not to crush the tip. Never use pliers or other tools

to retighten the ring on the cigarette lighter plug.

2. Pull the ring straight out, then remove the metal tip and old fuse.

3. Check the fuse to see if it has blown. If it has, replace it.

4. Replace the metal tip inside the ring, then place the fuse inside the cigarette lighter plug and screw the ring back onto the

plug. Make sure the metal tip is visible when you reassemble the cigarette lighter plug.

Return to contents

Charging the internal battery

Although the Syrius Plus can be charged using the cigarette lighter

in your vehicle, a complete charge is more easily achieved by using

the 240V AC mains charger included. When new, the battery in your

Syrius Plus is approximately 20% charged.

To charge the unit fully, move the ‘Batt. ON/OFF’ switch to the ‘OFF’

position and connect the 240V AC mains charger as indicated in the

picture on the right. The battery light on the Syrius Plus will illuminate

and will take approximately 3 hours to charge. When the internal

battery is fully charged, the red LED will turn blue. Once fully charged

the battery will last approximately 3 hrs during normal use.

Note: The new battery’s full performance is only achieved after two or

three complete charges and discharges.

Powering the Syrius Plus using the built-in battery

Once Syrius Plus is fully charged, it is ready for use. Move the ‘Batt. ON/OFF’ switch to the

‘ON’ position and press and hold the standby/power switch on the left hand side of the unit

for 2 seconds to switch on the device.

Low Battery Warning

If the Syrius Plus is powered from the internal battery and

the ‘Battery Low – Please Recharge’ warning is displayed

on the screen, the unit has approximately 20 to 30 minutes

of battery power remaining. You should either connect the

cigarette lighter adaptor lead to the unit whilst in the vehicle

or recharge the battery from the mains adapter supplied.

WARNING: PLEASE DO NOT USE OR LEAVE THE SYRIUS PLUS IN EITHER WET OR HUMID CONDITIONS, OR IN

EXTREME TEMPERATURES, AS THIS COULD PERMANENTLY DAMAGE THE UNIT AND THE BATTERY. WHEN

NOT IN USE DO NOT LEAVE THE UNIT ATTACHED TO THE WINDSCREEN, ESPECIALLY WHEN THE WEATHER

IS WARM, TO AVOID DAMAGE TO THE UNIT AND ALSO REDUCE THE RISK OF THEFT.

CAUTION: THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED WITH AN UNAPPROVED TYPE.

USING THE WRONG TYPE OF BATTERY MAY DAMAGE YOUR UNIT AND INVALIDATE YOUR WARRANTY.

ONLY SNOOPER AUTHORISED PERSONNEL SHOULD REPLACE THE BATTERY. PLEASE DISPOSE OF

USED BATTERIES ACCORDING TO LOCAL WASTE MANAGEMENT RULES AND REGULATIONS. FURTHER

INFORMATION CAN BE FOUND LATER IN THIS USER MANUAL.

Plug the charger into a

240V AC mains socket

Plug the charger cable

into the socket on the

back of the Syrius Plus

Return to contents

3D 2D North

Operating Instructions

1. Starting Up

Once you have synchronised the SD Card and

performed a download as necessary it is time to

perform the rst Start Up. First make sure your vehicle

is parked in as open a space as possible, clear of tall

trees and buildings so that the built in GPS antenna has

a clear view of the sky above. Next power the unit up by

moving the ‘Batt. ON/OFF’ switch to the ‘ON’ position

and then press and hold the standby power switch on

the left hand side of the unit for 2 seconds.

The unit will then start up and the following warning will

be displayed.

Please read the warning and press

to continue.

Whilst the Syrius Plus software is loading a start-up display will be shown for just a few seconds and then the screen

will show a section of a map. The Syrius Plus needs to acquire a minimum of four satellites in order to work. Once this

has been achieved the Syrius Plus will ascertain your position and this will be indicated by a green arrow icon on the on-

screen map and the GPS signal strength will be shown in the bottom right hand corner of the display. The Syrius Plus is

now ready to navigate.

As the GPS engine and antenna have never been used before, the rst ‘Cold’ start can take anywhere from 15

– 50 minutes to establish a satellite connection. Once initialised, subsequent start ups will take less time and

eventually should take only a matter of minutes.

2. Easy Set Up

2.1 Screen settings

There are a number of map views or different types of information that can be displayed on the screen at any one time:-

or Current time or vehicle speed - press to switch between the two.

or Estimated journey time or Estimated time of arrival

- press to switch between the two.

GPS Signal strength Battery status

Return to contents

To modify the information shown:

l Access the Menu by simply touching the Syrius Plus in the centre of the screen.

l Press the ‘Congure’ button.

l Press the

icon where you will see the list of options below.

l Select the option you wish to change on the left.

l To change a setting, simply press on the tick box to indicate which option you would like to choose.

l Continue to select each option and select your preference.

l Press ‘OK’ at the bottom of the screen to save your preferences.

Your chosen settings will now be saved and will appear on the screen each time you use your Syrius. If you want to switch

between your Current Speed and the Atomic Clock or the Estimated Time of Arrival and Time to Destination during your

journey simply touch the screen where either piece of information is displayed and the unit will display the alternate setting

and vice versa. However each time you power the device up the original setting will be displayed.

2.2

The Syrius Plus enables you to adjust the brightness of the display

and save two brightness settings: one for driving during the day

and one for driving at night. To adjust the brightness setting:

l Press the centre of the display to enter the ‘Menu’.

l Press the ‘Congure’ button.

l Press the ‘Brightness Control’ icon.

To set the daytime brightness select ‘DAY’ by checking the tick

box with your nger and then using the

and buttons to

adjust the setting.

To set the ‘NIGHT’ setting, simply check the tick box with your nger for ‘NIGHT’ and follow the same procedure. Once

you have selected the desired brightness press the ‘OK’ button at the bottom of the screen.

Note: The arrow icon in the bottom right hand corner of the display will return you to the ‘Congure’ menu if pressed

but will not store any changes you have made. You need to select the ‘OK’ button in order to save your changes.

Return to contents

2.3

The Syrius Plus volume can be adjusted using this function within

the ‘Congure’menu. To adjust the volume:

l Press the centre of the screen to access the ‘Menu’.

l Press ‘Congure’.

l Press the ‘Volume Control’ icon.

l To increase the volume press the

icon.

l To decrease the volume press the icon.

l To test the volume before saving, press the ‘Test’ icon.

l To reset the volume to the factory default press the ‘Reset’ icon.

l Press ‘OK’ at the bottom of the screen to save your setting.

Note: The arrow icon in the bottom right hand corner of the display will return you to the ‘Congure’ menu if pressed

but will not store any changes you have made. You need to select the ‘OK’ button in order to save your changes.

3. Planning a route

There are several ways to plan a route on the Syrius Plus.

3.1

l Press the centre of the screen to access the ‘Navigate to’

menu.

l Press the ‘Find by Post Code’ icon.

l If you have the European version of the Syrius Plus, you

will need to select the ‘Country’ rst BEFORE typing the

postcode. (If the correct country is already displayed, go to the next step). Use the arrow keys on the right of the display

to scroll up and down the country options. Select the country with your nger.

l Press ‘Post code’ and enter the full postcode using the onscreen keyboard.

l Press the ‘OK’ button on the keyboard.

Please Note: The button on the keyboard with no character on it is the ‘Space’ key. A space between the two

parts of the postcode MUST be entered in order for the postcode to be recognised.

If the following message is displayed ‘Please, input correct

postcode’, the postcode has been entered incorrectly. Press

OK and retype the postcode.

Return to contents

l The Syrius will display a screen showing the postcode and the street name.

l If you know the house/property number of your destination, press the ‘House No.’ button to enter it.

Once you have entered the house number press the ‘Ok’ button.

l Alternatively, if you do not have a house or building number, you can navigate to a point where two

roads meet instead. Press the ‘Intersection’ button and select the road.

l Press the ‘Calculate’ button.

Once the calculation is complete you can either press ‘Go’ to start navigation, ‘Simulation’ to see the actual route that

will be taken, ‘Route Option’ to change the parameters of the route or ‘Guide’ which will list the turn by turn instructions

of the journey. The ‘Summary Screen’ will tell you the distance to your destination, estimated time of arrival and the

estimated time it will take to complete your journey.

Please note: The summary screen is only displayed for approximately 10 seconds before the unit automatically

begins to provide you with turn-by-turn instructions.

User advice

By subscribing to and downloading the Enigma™ Speed Camera database you will

automatically be alerted to all ‘Fixed’ Speed Cameras and other Accident Hotspots

during your journey ensuring that you are always aware of the correct speed limit

whilst travelling along any particularly hazardous stretches of road.

3.2

If you do not know the postcode but have the street name and the town or city that

you would like to navigate to, then select this option.

l Press the centre of the screen to enter the ‘Navigate to’ menu.

l Press the ‘Find by City’ icon.

l If you have the European version of the Syrius Plus, you will need to select

the ‘Country’ rst BEFORE typing the city. (If the correct country is already

displayed, go to the next step). Use the arrow keys on the right of the display

to scroll up and down the country options. Select the country with your nger.

l Next press ‘City’ and enter the city name using the keyboard displayed.

As you begin to input the city name, the Syrius Plus will automatically prompt you

with a list of possible matches. If you can see the name of the destination you are

searching for in the lower window, you can select it easily by pressing that name

with your nger. If you wish to view the list of possible destinations in full press the

down arrow to the top right hand corner of the display and a list of cities will be

displayed then select your destination by touching on it. Use the arrow keys on the

right hand side of the display to scroll through the list.

l Press ‘Street’ and use the keyboard displayed to type in the street name.

As you begin to input the road or street name, the Syrius Plus will automatically

prompt you with a list of possible matches similar to when searching for ‘City’

described above. When you see the road you require select it by pressing it with

your nger.

l If you wish, you can enter the property number by pressing ‘House No.’ and

then typing the house number on the keyboard. Once the house number has

been selected, press the ‘OK’ button.

Return to contents

l Press the ‘Calculate’ button.

Once the calculation is complete you can either press ‘Go’ to start navigation,

‘Simulation’ to see the actual route that will be taken, ‘Route Option’ to change

the parameters of the route or ‘Guide’ which will list the turn by turn instructions of

the journey. The ‘Summary Screen’ will tell you the distance to your destination,

estimated time of arrival and the estimated time it will take to complete your journey

Please note: The summary screen is only displayed for approximately 10 seconds before the unit automatically

begins to provide you with turn-by-turn instructions.

3.3

You can navigate easily and quickly from a previous journey or destination to your home, by personalising your Syrius

Plus so that a route can be calculated by pressing just a few buttons.

3.3.1 Setting the ‘Home’ Destination

l Press the centre of the display to enter the ‘Navigate to’

menu.

l Press the ‘Home’ icon.

The rst time the ‘Home’ function is used an information

screen is displayed saying ‘Set Home? Press ‘OK’ in the

information window to continue, press cancel to exit. If

‘Home’ has already been set it can be edited in My

Favourites – refer to section 4 on page 25.

l You can search for your address by using one of the following options:

‘Find Address by City’ or ‘Find by Post Code’. Please refer to 3.1 and 3.2 above on how to use these functions.

Once you have entered the ‘Home’ destination, a new eld is available for you to ‘Name’ the destination.

l Press ‘Name’ and a keyboard will be displayed with the road name you selected.

l Press the ‘Arrow’ key to erase this data then input the new name using the keyboard.

Please note: You can enter a new name for the home destination using up to a maximum of sixteen characters.

l Press ‘Save’ once you have entered the name.

Once your home address has been saved, your Syrius Plus will be able to calculate a route to this address.

3.3.2 Using the ‘Home’ Function

To calculate a route:

l Press the centre of the display to enter the ‘Navigate to’ menu.

l Press the ‘Home’ icon.

The Syrius Plus will display details of the destination and offer a ‘Go’ button and a ‘Route Option’ button. Press ‘Go’ to

begin your journey.

Return to contents

3.4

You can navigate easily and quickly from a previous journey or destination to your ofce or place of work, by personalising

your Syrius Plus so that a route can be calculated by pressing just a few buttons.

3.4.1Settingthe‘Ofce’Destination

l Press the centre of the display to enter the ‘Navigate to’

menu.

l Press the ‘Ofce’ icon.

The rst time the ‘Ofce’ function is used an information

screen is displayed saying ‘Set Ofce? Press ‘OK’ in the

information window to continue, press cancel to exit.

If ‘Ofce’ has already been set it can be edited in My

Favourites – refer to section 4 on page 25.

l You can search for your address by using one of the following options:

‘Find Address by City’ or ‘Find by Post Code’. Please refer to 3.1 and 3.2 above on how to use these functions.

Once you have entered the ‘Ofce’ destination, a new eld is available for you to ‘Name’ the destination.

l Press ‘Name’ and a keyboard will be displayed with the road name you selected.

l Press the ‘Arrow’ key to erase this data then input the new name using the keyboard.

Please note: You can enter a new name for the ofce destination using up to a maximum of sixteen characters.

l Press ‘Save’ once you have entered the name.

Once your ofce address has been saved, your Syrius Plus will be able to calculate a route to this address.

3.4.2 Using the ‘Ofce’ Function

To calculate a route:

l Press the centre of the display to enter the ‘Navigate to’ menu.

l Press the ‘Ofce’ icon.

The Syrius Plus will display details of the destination and offer a ‘Go’ button and a ‘Route Option’ button. Press ‘Go’ to

begin your journey.

3.5

The Syrius Plus automatically stores the last route that has been calculated, so that if you wish to return to that address

you do not have to re-input all the details again.

To use this function:

l Press the centre of the screen to enter the ‘Navigate to’ menu.

l Press the ‘Recent Route’ icon.

The Syrius Plus will now calculate the route to your selected location.

Return to contents

Once a route has been calculated, the ‘Recent Route’ icon is replaced with a ‘Clear Route’ icon. To cancel a route that you

ha ve calculated:

l Press the centre of the screen to enter the ‘Navigate to’ menu.

l Press the ‘Clear Route’ icon.

The route will then automatically be deleted.

Please Note: For the ‘Clear Route’ feature to operate you will need to have entered and calculated a route. If the

‘Recent Route’ icon is displayed a route has NOT been entered.

3.6

With the Syrius Plus you have the facility to enter more than one destination at a time (for instance if you wish to visit other

locations before reaching your ultimate destination). You can store up to ten individual destinations. The unit will process

and calculate the destinations in the following order: A to B, B to C, and C to D etc. When entering the destinations you

are able to review the routes and change the order of the routes before pressing ‘Go’.

3.6.1 Create a Multi-route

l Press the centre of the display to enter the ‘Navigate to’

menu.

l Press the ‘Multi-route’ icon.

You will then see the ‘Multi-route screen’ that allows you to:

l Create a multi-route

l Use or edit a previously stored multi-route

l Delete a multi-route.

l Press ‘Create multi-route’.

The following screen is displayed where you can:

 > ‘Edit’ the name of the multi-route

 > Change the start point of the multi-route

 > ‘Add’ your destinations.

 > ‘Save’ your destinations

 > ‘Calculate’ your multi-route

l Press ‘Edit Name’ to create a name for your new multi-

route.

Please note: You can enter a new name for the multi-route

using up to a maximum of sixteen characters.

l Press the ‘Arrow’ key to delete the current name for your

multi-route.

l Type the new name of your multi-route using the keyboard.

l Press the ‘Save’ button in the top right hand corner.

If you wish to change the start position of the multi-route,

press ‘Change Start’ to change it. You are provided with

several options to select your start position. To nd out

how to use these options please refer to the applicable

sections earlier in this user manual.

Page is loading ...

Snooper syrius s600 plus User manual

Brand: Snooper

Model: syrius s600 plus

Category: Car navigation systems

Type: User manual

Download PDF

report

Snooper syrius s600 plus User manual

Snooper syrius s600 plus User manual

Related papers

Other documents